mirror of
https://github.com/openwrt/openwrt.git
synced 2024-12-30 18:47:06 +00:00
0b20490207
* QCA IPQ4019
* 256 MB of RAM
* 32 MB of SPI NOR flash (s25fl256s1)
- 2x 15 MB available; but one of the 15 MB regions is the recovery image
* 2T2R 2.4 GHz
- QCA4019 hw1.0 (SoC)
- requires special BDF in QCA4019/hw1.0/board-2.bin with
bus=ahb,bmi-chip-id=0,bmi-board-id=20,variant=OM-A62
* 2T2R 5 GHz (channel 36-64)
- QCA9888 hw2.0 (PCI)
- requires special BDF in QCA9888/hw2.0/board-2.bin
bus=pci,bmi-chip-id=0,bmi-board-id=16,variant=OM-A62
* 2T2R 5 GHz (channel 100-165)
- QCA4019 hw1.0 (SoC)
- requires special BDF in QCA4019/hw1.0/board-2.bin with
bus=ahb,bmi-chip-id=0,bmi-board-id=21,variant=OM-A62
* multi-color LED (controlled via red/green/blue GPIOs)
* 1x button (reset; kmod-input-gpio-keys compatible)
* external watchdog
- triggered GPIO
* 1x USB (xHCI)
* TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX)
* 2x gigabit ethernet
- phy@mdio3:
+ Label: Ethernet 1
+ gmac0 (ethaddr) in original firmware
+ 802.3at POE+
- phy@mdio4:
+ Label: Ethernet 2
+ gmac1 (eth1addr) in original firmware
+ 18-24V passive POE (mode B)
* powered only via POE
The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
used to transfer the factory image to the u-boot when the device boots up.
The initramfs image can be started using
setenv bootargs 'loglevel=8 earlycon=msm_serial_dm,0x78af000 console=ttyMSM0,115200 mtdparts=spi0.0:256k(0:SBL1),128k(0:MIBIB),384k(0:QSEE),64k(0:CDT),64k(0:DDRPARAMS),64k(0:APPSBLENV),512k(0:APPSBL),64k(0:ART),64k(0:custom),64k(0:KEYS),15552k(inactive),15552k(inactive2)'
tftpboot 0x84000000 openwrt-ipq40xx-openmesh_a62-initramfs-fit-uImage.itb
set fdt_high 0x85000000
bootm 0x84000000
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
32 lines
955 B
Diff
32 lines
955 B
Diff
From 8f68331e14dff9a101f2d0e1d6bec84a031f27ee Mon Sep 17 00:00:00 2001
|
|
From: John Crispin <john@phrozen.org>
|
|
Date: Thu, 9 Mar 2017 11:03:18 +0100
|
|
Subject: [PATCH 69/69] arm: boot: add dts files
|
|
|
|
Signed-off-by: John Crispin <john@phrozen.org>
|
|
---
|
|
arch/arm/boot/dts/Makefile | 8 ++++++++
|
|
1 file changed, 8 insertions(+)
|
|
|
|
--- a/arch/arm/boot/dts/Makefile
|
|
+++ b/arch/arm/boot/dts/Makefile
|
|
@@ -697,7 +697,18 @@ dtb-$(CONFIG_ARCH_QCOM) += \
|
|
qcom-apq8074-dragonboard.dtb \
|
|
qcom-apq8084-ifc6540.dtb \
|
|
qcom-apq8084-mtp.dtb \
|
|
+ qcom-ipq4018-a42.dtb \
|
|
+ qcom-ipq4018-ex6100v2.dtb \
|
|
+ qcom-ipq4018-ex6150v2.dtb \
|
|
+ qcom-ipq4018-fritz4040.dtb \
|
|
+ qcom-ipq4018-jalapeno.dtb \
|
|
+ qcom-ipq4018-rt-ac58u.dtb \
|
|
qcom-ipq4019-ap.dk01.1-c1.dtb \
|
|
+ qcom-ipq4019-a62.dtb \
|
|
+ qcom-ipq4019-ap.dk04.1-c1.dtb \
|
|
+ qcom-ipq4028-wpj428.dtb \
|
|
+ qcom-ipq4029-gl-b1300.dtb \
|
|
+ qcom-ipq4029-mr33.dtb \
|
|
qcom-ipq8064-ap148.dtb \
|
|
qcom-msm8660-surf.dtb \
|
|
qcom-msm8960-cdp.dtb \
|