mirror of
https://github.com/openwrt/openwrt.git
synced 2024-12-26 17:01:14 +00:00
b4184c666c
This patch adds support for Linksys WHW01 v1 ("Velop") [FCC ID Q87-03331]. Specification ------------- SOC: Qualcomm IPQ4018 WiFi 1: Qualcomm QCA4019 IEEE 802.11b/g/n WiFi 2: Qualcomm QCA4019 IEEE 802.11a/n/ac Bluetooth: Qualcomm CSR8811 (A12U) Ethernet: Qualcomm QCA8072 (2-port) SPI Flash 1: Mactronix MX25L1605D (2MB) SPI Flash 2: Winbond W25M02GV (256MB) DRAM: Nanya NT5CC128M16IP-DI (256MB) LED Controller: NXP PCA963x (I2C) Buttons: Single reset button (GPIO). Notes ----- There does not appear to be a way to trigger TFTP recovery without entering U-Boot. The device must be opened to access the serial console in order to first flash OpenWrt onto a device from factory. The device has automatic recovery backed by a second set of partitions on the larger of the two SPI flash ICs. Both the primary and secondary must be flashed to prevent accidental rollback to "factory" after 3 failed boot attempts. Serial console -------------- A serial console is available on the following pins of the populated J2 connector on the device mainboard (115200 8n1). (<-- Top of PCB / Device) J2 [o o o o o o] | | | | | `-- GND | `---- TX `--------- RX Installation instructions ------------------------- 1. Setup TFTP server with server IP set to 192.168.1.236. 2. Copy compiled `...squashfs-factory.bin` to `nodes-jr.img` in tftp root. 3. Connect to console using pinout detailed in the serial console section. 4. Power on device and press enter when prompted to drop into U-Boot. 5. Flash first partition device via `run flashimg`. 6. Once complete, reset device and allow to power up completely. 7. Once comfortable with device upgrade reboot and drop back into U-Boot. 8. Flash the second partition (recovery) via `run flashimg2`. Revert to "factory" ------------------- 1. Download latest firmware update from vendor support site. 2. Copy extracted `.img` file to `nodes-jr.img` in tftp root. 3. Connect to console using pinout detailed in the serial console section. 4. Power on device and press enter when prompted to drop into U-Boot. 5. Flash first partition device via `run flashimg`. 6. Once complete, reset device and allow to power up completely. 7. Once comfortable with device upgrade reboot and drop back into U-Boot. 8. Flash the second partition (recovery) via `run flashimg2`. Link: https://github.com/openwrt/openwrt/pull/3682 Signed-off-by: Peter Adkins <peter@sunkenlab.com> (calibration from nvmem, updated to 5.10+5.15) Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
75 lines
1.7 KiB
Plaintext
75 lines
1.7 KiB
Plaintext
#
|
|
# Copyright (C) 2016 LEDE
|
|
#
|
|
|
|
[ -e /etc/config/ubootenv ] && exit 0
|
|
|
|
touch /etc/config/ubootenv
|
|
|
|
. /lib/uboot-envtools.sh
|
|
. /lib/functions.sh
|
|
|
|
board=$(board_name)
|
|
|
|
ubootenv_mtdinfo () {
|
|
UBOOTENV_PART=$(cat /proc/mtd | grep APPSBLENV)
|
|
mtd_dev=$(echo $UBOOTENV_PART | awk '{print $1}' | sed 's/:$//')
|
|
mtd_size=$(echo $UBOOTENV_PART | awk '{print "0x"$2}')
|
|
mtd_erase=$(echo $UBOOTENV_PART | awk '{print "0x"$3}')
|
|
nor_flash=$(find /sys/bus/spi/devices/*/mtd -name ${mtd_dev})
|
|
|
|
if [ -n "$nor_flash" ]; then
|
|
ubootenv_size=$mtd_size
|
|
else
|
|
# size is fixed to 0x40000 in u-boot
|
|
ubootenv_size=0x40000
|
|
fi
|
|
|
|
sectors=$(( $ubootenv_size / $mtd_erase ))
|
|
echo /dev/$mtd_dev 0x0 $ubootenv_size $mtd_erase $sectors
|
|
}
|
|
|
|
case "$board" in
|
|
alfa-network,ap120c-ac|\
|
|
devolo,magic-2-wifi-next|\
|
|
edgecore,ecw5211|\
|
|
glinet,gl-ap1300|\
|
|
glinet,gl-b1300|\
|
|
glinet,gl-b2200|\
|
|
luma,wrtq-329acn|\
|
|
netgear,wac510|\
|
|
openmesh,a42|\
|
|
openmesh,a62|\
|
|
plasmacloud,pa1200|\
|
|
plasmacloud,pa2200)
|
|
ubootenv_add_uci_config "/dev/mtd5" "0x0" "0x10000" "0x10000"
|
|
;;
|
|
aruba,ap-303)
|
|
ubootenv_add_uci_config "/dev/mtd13" "0x0" "0x10000" "0x10000"
|
|
;;
|
|
aruba,ap-365)
|
|
ubootenv_add_uci_config "/dev/mtd8" "0x0" "0x10000" "0x10000"
|
|
;;
|
|
buffalo,wtr-m2133hp)
|
|
ubootenv_add_uci_config "/dev/mtd8" "0x0" "0x40000" "0x20000"
|
|
;;
|
|
linksys,ea6350v3)
|
|
ubootenv_add_uci_config "/dev/mtd7" "0x0" "0x20000" "0x20000"
|
|
;;
|
|
linksys,ea8300|\
|
|
linksys,mr8300)
|
|
ubootenv_add_uci_config "/dev/mtd7" "0x0" "0x40000" "0x20000"
|
|
;;
|
|
linksys,whw01-v1)
|
|
ubootenv_add_uci_config "/dev/mtd6" "0x0" "0x40000" "0x10000"
|
|
;;
|
|
zyxel,nbg6617)
|
|
ubootenv_add_uci_config "/dev/mtd6" "0x0" "0x10000" "0x10000"
|
|
;;
|
|
esac
|
|
|
|
config_load ubootenv
|
|
config_foreach ubootenv_add_app_config ubootenv
|
|
|
|
exit 0
|