mirror of
https://github.com/openwrt/openwrt.git
synced 2024-12-23 15:32:33 +00:00
95b0c07a61
Hardware
--------
CPU: Qualcomm IPQ4019
RAM: 256M
FLASH: 128M NAND
ETH: QCA8075
VDSL: Intel/Lantiq VRX518 PCIe attached
currently not supported
DECT: Dialog SC14448
currently not supported
WiFi2: IPQ4019 2T2R 2SS b/g/n
WiFi5: IPQ4019 2T2R 2SS n/ac
LED: - Power/DSL green
- WLAN green
- FON/DECT green
- Connect/WPS green
- Info green
- Info red
BTN: - WLAN
- FON
- WPS/Connect
UART: 115200n8 3.3V (located under the Dialog chip)
VCC - RX - TX - GND (Square is VCC)
Installation
------------
1. Grab the uboot for the Device from the 'u-boot-fritz7530'
subdirectory. Place it in the same directory as the 'eva_ramboot.py'
script. It is located in the 'scripts/flashing' subdirectory of the
OpenWRT tree.
2. Assign yourself the IP address 192.168.178.10/24. Connect your
Computer to one of the boxes LAN ports.
3. Connect Power to the Box. As soon as the LAN port of your computer
shows link, load the U-Boot to the box using following command.
> ./eva_ramboot.py --offset 0x85000000 192.168.178.1 uboot-fritz7530.bin
4. The U-Boot will now start. Now assign yourself the IP address
192.168.1.70/24. Copy the OpenWRT initramfs (!) image to a TFTP
server root directory and rename it to 'FRITZ7530.bin'.
5. The Box will now boot OpenWRT from RAM. This can take up to two
minutes.
6. Copy the U-Boot and the OpenWRT sysupgrade (!) image to the Box using
scp. SSH into the Box and first write the Bootloader to both previous
kernel partitions.
> mtd write /path/to/uboot-fritz7530.bin uboot0
> mtd write /path/to/uboot-fritz7530.bin uboot1
7. Remove the AVM filesystem partitions to make room for our kernel +
rootfs + overlayfs.
> ubirmvol /dev/ubi0 --name=avm_filesys_0
> ubirmvol /dev/ubi0 --name=avm_filesys_1
8. Flash OpenWRT peristently using sysupgrade.
> sysupgrade -n /path/to/openwrt-sysupgrade.bin
Signed-off-by: David Bauer <mail@david-bauer.net>
[removed pcie-dts range node, refreshed on top of AP120-AC/E2600AC]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
219 lines
5.6 KiB
Bash
219 lines
5.6 KiB
Bash
#!/bin/sh
|
|
|
|
# xor multiple hex values of the same length
|
|
xor() {
|
|
local val
|
|
local ret="0x$1"
|
|
local retlen=${#1}
|
|
|
|
shift
|
|
while [ -n "$1" ]; do
|
|
val="0x$1"
|
|
ret=$((ret ^ val))
|
|
shift
|
|
done
|
|
|
|
printf "%0${retlen}x" "$ret"
|
|
}
|
|
|
|
ath10kcal_die() {
|
|
echo "ath10cal: " "$*"
|
|
exit 1
|
|
}
|
|
|
|
ath10kcal_extract() {
|
|
local part=$1
|
|
local offset=$2
|
|
local count=$3
|
|
local mtd
|
|
|
|
mtd=$(find_mtd_chardev $part)
|
|
[ -n "$mtd" ] || \
|
|
ath10kcal_die "no mtd device found for partition $part"
|
|
|
|
dd if=$mtd of=/lib/firmware/$FIRMWARE iflag=skip_bytes bs=$count skip=$offset count=1 2>/dev/null || \
|
|
ath10kcal_die "failed to extract calibration data from $mtd"
|
|
}
|
|
|
|
ath10kcal_ubi_extract() {
|
|
local part=$1
|
|
local offset=$2
|
|
local count=$3
|
|
local ubidev
|
|
local ubi
|
|
|
|
. /lib/upgrade/nand.sh
|
|
|
|
ubidev=$(nand_find_ubi $CI_UBIPART)
|
|
ubi=$(nand_find_volume $ubidev $part)
|
|
[ -n "$ubi" ] || \
|
|
ath10kcal_die "no UBI volume found for $part"
|
|
|
|
dd if=/dev/$ubi of=/lib/firmware/$FIRMWARE iflag=skip_bytes bs=$count skip=$offset count=1 2>/dev/null || \
|
|
ath10kcal_die "failed to extract from $ubi"
|
|
}
|
|
|
|
ath10kcal_patch_mac_crc() {
|
|
local mac=$1
|
|
local mac_offset=6
|
|
local chksum_offset=2
|
|
local xor_mac
|
|
local xor_fw_mac
|
|
local xor_fw_chksum
|
|
|
|
[ -z "$mac" ] && return
|
|
|
|
xor_fw_mac=$(hexdump -v -n 6 -s $mac_offset -e '/1 "%02x"' /lib/firmware/$FIRMWARE)
|
|
xor_fw_mac="${xor_fw_mac:0:4} ${xor_fw_mac:4:4} ${xor_fw_mac:8:4}"
|
|
|
|
macaddr_2bin $mac | dd of=/lib/firmware/$FIRMWARE conv=notrunc bs=1 seek=6 count=6
|
|
|
|
xor_mac=${mac//:/}
|
|
xor_mac="${xor_mac:0:4} ${xor_mac:4:4} ${xor_mac:8:4}"
|
|
|
|
xor_fw_chksum=$(hexdump -v -n 2 -s $chksum_offset -e '/1 "%02x"' /lib/firmware/$FIRMWARE)
|
|
xor_fw_chksum=$(xor $xor_fw_chksum $xor_fw_mac $xor_mac)
|
|
|
|
printf "%b" "\x${xor_fw_chksum:0:2}\x${xor_fw_chksum:2:2}" | \
|
|
dd of=/lib/firmware/$FIRMWARE conv=notrunc bs=1 seek=$chksum_offset count=2
|
|
}
|
|
|
|
ath10kcal_is_caldata_valid() {
|
|
local expected="$1"
|
|
|
|
magic=$(hexdump -v -n 2 -e '1/1 "%02x"' /lib/firmware/$FIRMWARE)
|
|
[[ "$magic" == "$expected" ]]
|
|
return $?
|
|
}
|
|
|
|
[ -e /lib/firmware/$FIRMWARE ] && exit 0
|
|
|
|
. /lib/functions.sh
|
|
. /lib/functions/system.sh
|
|
|
|
board=$(board_name)
|
|
|
|
|
|
case "$FIRMWARE" in
|
|
"ath10k/cal-pci-0000:01:00.0.bin")
|
|
case "$board" in
|
|
meraki,mr33)
|
|
ath10kcal_ubi_extract "ART" 36864 2116
|
|
ath10kcal_is_caldata_valid "4408" || ath10kcal_extract "ART" 36864 2116
|
|
ath10kcal_patch_mac_crc $(macaddr_add $(get_mac_binary "/sys/bus/i2c/devices/0-0050/eeprom" 102) +1)
|
|
;;
|
|
esac
|
|
;;
|
|
"ath10k/pre-cal-pci-0000:01:00.0.bin")
|
|
case "$board" in
|
|
asus,map-ac2200)
|
|
ath10kcal_ubi_extract "Factory" 36864 12064
|
|
ln -sf /lib/firmware/ath10k/pre-cal-pci-0000\:00\:00.0.bin \
|
|
/lib/firmware/ath10k/QCA9888/hw2.0/board.bin
|
|
;;
|
|
openmesh,a62)
|
|
ath10kcal_extract "0:ART" 36864 12064
|
|
;;
|
|
esac
|
|
;;
|
|
"ath10k/pre-cal-ahb-a000000.wifi.bin")
|
|
case "$board" in
|
|
8dev,jalapeno |\
|
|
alfa-network,ap120c-ac |\
|
|
glinet,gl-b1300 |\
|
|
linksys,ea6350v3 |\
|
|
qcom,ap-dk01.1-c1)
|
|
ath10kcal_extract "ART" 4096 12064
|
|
;;
|
|
asus,map-ac2200)
|
|
ath10kcal_ubi_extract "Factory" 4096 12064
|
|
;;
|
|
asus,rt-ac58u)
|
|
CI_UBIPART=UBI_DEV
|
|
ath10kcal_ubi_extract "Factory" 4096 12064
|
|
;;
|
|
avm,fritzbox-4040)
|
|
/usr/bin/fritz_cal_extract -i 1 -s 0x400 -e 0x207 -l 12064 -o /lib/firmware/$FIRMWARE $(find_mtd_chardev "urlader_config")
|
|
;;
|
|
avm,fritzbox-7530)
|
|
/usr/bin/fritz_cal_extract -i 1 -s 0x3C000 -e 0x207 -l 12064 -o /lib/firmware/$FIRMWARE $(find_mtd_chardev "urlader0") || \
|
|
/usr/bin/fritz_cal_extract -i 1 -s 0x3C000 -e 0x207 -l 12064 -o /lib/firmware/$FIRMWARE $(find_mtd_chardev "urlader1")
|
|
;;
|
|
compex,wpj428 |\
|
|
engenius,eap1300 |\
|
|
openmesh,a42 |\
|
|
openmesh,a62 |\
|
|
qxwlan,e2600ac-c1 |\
|
|
qxwlan,e2600ac-c2)
|
|
ath10kcal_extract "0:ART" 4096 12064
|
|
;;
|
|
meraki,mr33)
|
|
ath10kcal_ubi_extract "ART" 4096 12064
|
|
ath10kcal_is_caldata_valid "202f" || ath10kcal_extract "ART" 4096 12064
|
|
ath10kcal_patch_mac_crc $(macaddr_add $(get_mac_binary "/sys/bus/i2c/devices/0-0050/eeprom" 102) +2)
|
|
;;
|
|
netgear,ex6100v2 |\
|
|
netgear,ex6150v2)
|
|
ath10kcal_extract "ART" 4096 12064
|
|
ath10kcal_patch_mac_crc $(mtd_get_mac_binary dnidata 0)
|
|
;;
|
|
zyxel,nbg6617 |\
|
|
zyxel,wre6606)
|
|
ath10kcal_extract "ART" 4096 12064
|
|
ath10kcal_patch_mac_crc $(macaddr_add $(cat /sys/class/net/eth0/address) -2)
|
|
;;
|
|
esac
|
|
;;
|
|
"ath10k/pre-cal-ahb-a800000.wifi.bin")
|
|
case "$board" in
|
|
8dev,jalapeno |\
|
|
alfa-network,ap120c-ac |\
|
|
glinet,gl-b1300 |\
|
|
linksys,ea6350v3 |\
|
|
qcom,ap-dk01.1-c1)
|
|
ath10kcal_extract "ART" 20480 12064
|
|
;;
|
|
asus,map-ac2200)
|
|
ath10kcal_ubi_extract "Factory" 20480 12064
|
|
;;
|
|
asus,rt-ac58u)
|
|
CI_UBIPART=UBI_DEV
|
|
ath10kcal_ubi_extract "Factory" 20480 12064
|
|
;;
|
|
avm,fritzbox-4040)
|
|
/usr/bin/fritz_cal_extract -i 1 -s 0x400 -e 0x208 -l 12064 -o /lib/firmware/$FIRMWARE $(find_mtd_chardev "urlader_config")
|
|
;;
|
|
avm,fritzbox-7530)
|
|
/usr/bin/fritz_cal_extract -i 1 -s 0x3C800 -e 0x208 -l 12064 -o /lib/firmware/$FIRMWARE $(find_mtd_chardev "urlader0") || \
|
|
/usr/bin/fritz_cal_extract -i 1 -s 0x3C800 -e 0x208 -l 12064 -o /lib/firmware/$FIRMWARE $(find_mtd_chardev "urlader1")
|
|
;;
|
|
compex,wpj428 |\
|
|
engenius,eap1300 |\
|
|
openmesh,a42 |\
|
|
openmesh,a62 |\
|
|
qxwlan,e2600ac-c1 |\
|
|
qxwlan,e2600ac-c2)
|
|
ath10kcal_extract "0:ART" 20480 12064
|
|
;;
|
|
meraki,mr33)
|
|
ath10kcal_ubi_extract "ART" 20480 12064
|
|
ath10kcal_is_caldata_valid "202f" || ath10kcal_extract "ART" 20480 12064
|
|
ath10kcal_patch_mac_crc $(macaddr_add $(get_mac_binary "/sys/bus/i2c/devices/0-0050/eeprom" 102) +3)
|
|
;;
|
|
netgear,ex6100v2 |\
|
|
netgear,ex6150v2)
|
|
ath10kcal_extract "ART" 20480 12064
|
|
ath10kcal_patch_mac_crc $(mtd_get_mac_binary dnidata 12)
|
|
;;
|
|
zyxel,nbg6617 |\
|
|
zyxel,wre6606)
|
|
ath10kcal_extract "ART" 20480 12064
|
|
ath10kcal_patch_mac_crc $(macaddr_add $(cat /sys/class/net/eth0/address) -1)
|
|
;;
|
|
esac
|
|
;;
|
|
*)
|
|
exit 1
|
|
;;
|
|
esac
|