openwrt/package/boot/uboot-envtools/files
Chris Blake 949e8ba521 ath79: add support for Netgear PGZNG1
This adds support for the Netgear PGZNG1, also known as the ADT Pulse
Gateway.

Hardware:
CPU: Atheros AR9344
Memory: 256MB
Storage: 256MB NAND Hynix H27U2G8F2CTR-BC
USB: 1x USB 2.0
Ethernet: 2x 100Mb/s
WiFi: Atheros AR9340 2.4GHz 2T2R
Leds: 8 LEDs
Button: 1x Reset Button
UART:
Header marked JPE1. Pinout is VCC, TX, RX, GND. The marked pin, closest
to the JPE1 marking, is VCC. Note VCC isn't required to be connected
for UART to work.

Enable Stock Firmware Shell Access:
1. Interrupt u-boot and run the following commands
setenv console_mode 1
saveenv
reset

This will enable a UART shell in the firmware. You can then login using
the root password of `icontrol`. If that doesn't work, the device is
running a firmware based on OpenWRT where you can drop into failsafe to
mount the FS and then modify /etc/passwd.

Installation Instructions:
1. Interupt u-boot and run the following commands
setenv active_image 0
setenv stock_bootcmd nboot 0x81000000 0 \${kernel_offset}
setenv openwrt_bootcmd nboot 0x82000000 0 \${kernel_offset}
setenv bootcmd run openwrt_bootcmd
saveenv

2. boot initramfs image via TFTP u-boot
tftpboot 0x82000000 openwrt-ath79-nand-netgear_pgzng1-initramfs-kernel.bin; bootm 0x82000000

3. Once booted, use LuCI sysupgrade to
flash openwrt-ath79-nand-netgear_pgzng1-squashfs-sysupgrade.bin

MAC Table:
WAN (eth0): xx:xa - caldata 0x0
LAN (eth1): xx:xb - caldata 0x6
WLAN (phy0): xx:xc - burned into ath9k caldata

Not Working:
Z-Wave
RS422

Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
(added more hw-info, fixed file permissions)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2022-06-19 12:31:02 +02:00
..
apm821xx apm821xx: MBL: make mtd chip work 2022-06-19 12:31:02 +02:00
ath79 ath79: add support for Netgear PGZNG1 2022-06-19 12:31:02 +02:00
cns3xxx uboot-envtools: drop shebang from uci-defaults and lib files 2021-04-10 15:18:14 +02:00
fw_printsys uboot-envtools: add wrapper scripts for alternate config 2021-04-08 09:20:59 +02:00
fw_setsys uboot-envtools: add wrapper scripts for alternate config 2021-04-08 09:20:59 +02:00
imx_cortexa9 uboot-envtools: move imx to imx_cortexa9 2021-11-03 12:45:40 +01:00
ipq40xx ipq40xx: add support for Linksys WHW01 v1 2022-06-05 21:19:32 +02:00
ipq806x ipq806x: add support for Arris TR4400 v2 / RAC2V1A 2022-05-05 09:19:00 +09:00
kirkwood kirkwood: add support for NETGEAR ReadyNAS Duo v2 2021-12-29 20:35:57 +01:00
lantiq uboot-envtools: drop shebang from uci-defaults and lib files 2021-04-10 15:18:14 +02:00
layerscape uboot-envtools: layerscape: drop redundant space after case keywords 2021-04-10 15:18:41 +02:00
mediatek_mt7622 mediatek: Add support for Xiaomi Redmi Router AX6S 2022-03-20 18:33:39 +00:00
mediatek_mt7623 uboot-envtools: add configuration for UniElec U7623 board 2022-01-23 20:20:42 +00:00
mpc85xx uboot-envtools: add WS-AP3825i config 2022-04-26 00:57:22 +02:00
mvebu mvebu: add Globalscale MOCHAbin 2021-10-02 16:45:35 +02:00
mxs uboot-envtools: drop shebang from uci-defaults and lib files 2021-04-10 15:18:14 +02:00
oxnas uboot-envtools: oxnas: fix wrong eraseblock size for shuttle,kd20 2022-03-21 20:16:16 +00:00
pistachio uboot-envtools: drop shebang from uci-defaults and lib files 2021-04-10 15:18:14 +02:00
qoriq qoriq: add support for WatchGuard Firebox M300 2021-12-21 21:37:46 +02:00
ramips ramips: add support for MTS WG430223 2022-06-13 15:26:23 +08:00
realtek realtek: add support for D-Link DGS-1210-20 2022-06-19 08:36:21 +02:00
uboot-envtools.sh uboot-envtools: add support for multiple config partitions 2021-04-08 09:20:59 +02:00