openwrt/target/linux/ath79/dts/ar7242_avm_fritz300e.dts
Adrian Schmutzler 50fdc0374b ath79: provide label MAC address
This patch adds the label MAC address for several devices in
ath79.

Some devices require setting the MAC address in 02_network:

For the following devices, the netif device can be linked in
device tree, but the MAC address cannot be read:
- alfa-network,ap121f
- avm,fritz300e
- ubnt-xm devices

For the following devices, label MAC address is tied to lan or
wan, so no node to link to exists in device tree:
- adtran,bsap1800-v2
- adtran,bsap1840
- dlink,dir-842-c1/-c2/-c3
- engenius,ecb1750
- iodata,etg3-r
- iodata,wn-ac1167dgr
- iodata,wn-ac1600dgr
- iodata,wn-ac1600dgr2
- iodata,wn-ag300dgr
- nec,wg800hp
- nec,wg1200cr
- trendnet,tew-823dru

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-09-19 23:43:27 +02:00

171 lines
2.7 KiB
Plaintext

// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
/dts-v1/;
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/input/input.h>
#include "ar7242.dtsi"
/ {
compatible = "avm,fritz300e", "qca,ar7242";
model = "AVM FRITZ!WLAN Repeater 300E";
aliases {
led-boot = &power;
led-failsafe = &power;
led-running = &power;
led-upgrade = &power;
label-mac-device = &ath9k;
};
keys {
compatible = "gpio-keys-polled";
poll-interval = <20>;
wps {
label = "wps";
linux,code = <KEY_WPS_BUTTON>;
gpios = <&gpio 12 GPIO_ACTIVE_LOW>;
debounce-interval = <60>;
};
};
leds {
compatible = "gpio-leds";
power: power {
label = "fritz300e:green:power";
gpios = <&gpio 13 GPIO_ACTIVE_LOW>;
default-state = "on";
};
lan {
label = "fritz300e:green:lan";
gpios = <&gpio 15 GPIO_ACTIVE_LOW>;
};
wlan {
label = "fritz300e:green:wlan";
gpios = <&gpio 16 GPIO_ACTIVE_LOW>;
linux,default-trigger = "phy0tpt";
};
};
ath9k-leds {
compatible = "gpio-leds";
rssi0 {
label = "fritz300e:green:rssi0";
gpios = <&ath9k 10 GPIO_ACTIVE_LOW>;
};
rssi1 {
label = "fritz300e:green:rssi1";
gpios = <&ath9k 4 GPIO_ACTIVE_LOW>;
};
rssi2 {
label = "fritz300e:green:rssi2";
gpios = <&ath9k 6 GPIO_ACTIVE_LOW>;
};
rssi3 {
label = "fritz300e:green:rssi3";
gpios = <&ath9k 7 GPIO_ACTIVE_LOW>;
};
rssi4 {
label = "fritz300e:green:rssi4";
gpios = <&ath9k 5 GPIO_ACTIVE_LOW>;
};
};
eth-phy-reset {
compatible = "regulator-fixed";
regulator-name = "eth-phy-reset";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
gpio = <&gpio 11 GPIO_ACTIVE_LOW>;
startup-delay-us = <300000>;
enable-active-high;
regulator-always-on;
};
};
&spi {
status = "okay";
num-cs = <1>;
flash@0 {
compatible = "jedec,spi-nor";
reg = <0>;
spi-max-frequency = <25000000>;
partitions {
compatible = "fixed-partitions";
#address-cells = <1>;
#size-cells = <1>;
partition@0 {
reg = <0x0 0x20000>;
label = "urloader";
read-only;
};
partition@20000 {
compatible = "avm,eva-firmware";
reg = <0x20000 0xee0000>;
label = "firmware";
};
partition@f00000 {
reg = <0xf00000 0x80000>;
label = "tffs (1)";
read-only;
};
partition@f80000 {
reg = <0xf80000 0x80000>;
label = "tffs (2)";
read-only;
};
};
};
};
&uart {
status = "okay";
};
&pcie {
status = "okay";
ath9k: wifi@0,0 {
reg = <0x0000 0 0 0 0>;
#gpio-cells = <2>;
gpio-controller;
qca,no-eeprom;
};
};
&mdio0 {
status = "okay";
phy0: ethernet-phy@0 {
reg = <0>;
phy-mode = "rgmii";
};
};
&eth0 {
status = "okay";
phy-mode = "rgmii";
phy-handle = <&phy0>;
pll-data = <0x16000000 0x00000101 0x00001313>;
};