mirror of
https://github.com/openwrt/openwrt.git
synced 2024-12-19 13:48:06 +00:00
640b0b79ff
Hardware specification: SoC: MediaTek MT7981B 2x A53 Flash: 8GB eMMC or 128 MB SPI-NAND RAM: 256MB Ethernet: 5x 10/100/1000 Mbps Switch: MediaTek MT7531AE WiFi: MediaTek MT7976C Button: Reset USB: M.2(B-key) for 4G/5G Module Power: DC 12V 1A UART: 3.3v, 115200n8 -------------------------- | Layout | | ----------------- | | 4 | VCC RX TX GND | <= | | ----------------- | -------------------------- The U-boot menu will automatically appear at startup, and then select the required options through UP/DOWN Key. NAND Flash and eMMC Flash instructions: 1. Set your computers IP adress to 192.168.1.2. 2. Run a TFTP server providing the sysupgrade.bin image. 3. Power on the router, into the U-Boot menu. 4. Select "2. Upgrade firmware" 5. Update sysupgrade.bin file name, input server IP and input device IP (if they deviate from the defaults) 6. Wait for automatic startup after burning Signed-off-by: Allen Zhao <allenzhao@unielecinc.com>
125 lines
1.8 KiB
Plaintext
125 lines
1.8 KiB
Plaintext
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
|
/*
|
|
* Copyright (C) 2023 Allen Zhao <allenzhao@unielecinc.com>
|
|
*/
|
|
|
|
/dts-v1/;
|
|
#include "mt7981.dtsi"
|
|
/ {
|
|
model = "Unielec U7981-01 (EMMC)";
|
|
compatible = "unielec,u7981-01-emmc", "mediatek,mt7981";
|
|
|
|
chosen {
|
|
bootargs = "console=ttyS0,115200n1 loglevel=8 \
|
|
earlycon=uart8250,mmio32,0x11002000 \
|
|
";
|
|
};
|
|
|
|
gpio-keys {
|
|
compatible = "gpio-keys";
|
|
reset {
|
|
label = "reset";
|
|
linux,code = <KEY_RESTART>;
|
|
gpios = <&pio 1 GPIO_ACTIVE_LOW>;
|
|
};
|
|
};
|
|
};
|
|
|
|
&uart0 {
|
|
status = "okay";
|
|
};
|
|
|
|
&watchdog {
|
|
status = "okay";
|
|
};
|
|
|
|
ð {
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&mdio_pins &gbe_led0_pins &gbe_led1_pins>;
|
|
status = "okay";
|
|
|
|
gmac0: mac@0 {
|
|
/* LAN */
|
|
compatible = "mediatek,eth-mac";
|
|
reg = <0>;
|
|
phy-mode = "2500base-x";
|
|
|
|
fixed-link {
|
|
speed = <2500>;
|
|
full-duplex;
|
|
pause;
|
|
};
|
|
};
|
|
|
|
gmac1: mac@1 {
|
|
/* WAN */
|
|
compatible = "mediatek,eth-mac";
|
|
reg = <1>;
|
|
phy-mode = "gmii";
|
|
phy-handle = <&int_gbe_phy>;
|
|
};
|
|
};
|
|
|
|
&mdio_bus {
|
|
switch: switch@1f {
|
|
compatible = "mediatek,mt7531";
|
|
reg = <31>;
|
|
reset-gpios = <&pio 39 GPIO_ACTIVE_HIGH>;
|
|
interrupt-controller;
|
|
#interrupt-cells = <1>;
|
|
interrupt-parent = <&pio>;
|
|
interrupts = <38 IRQ_TYPE_LEVEL_HIGH>;
|
|
};
|
|
};
|
|
|
|
&switch {
|
|
ports {
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
|
|
port@0 {
|
|
reg = <0>;
|
|
label = "lan1";
|
|
};
|
|
|
|
port@1 {
|
|
reg = <1>;
|
|
label = "lan2";
|
|
};
|
|
|
|
port@2 {
|
|
reg = <2>;
|
|
label = "lan3";
|
|
};
|
|
|
|
port@3 {
|
|
reg = <3>;
|
|
label = "lan4";
|
|
};
|
|
|
|
port@6 {
|
|
reg = <6>;
|
|
label = "cpu";
|
|
ethernet = <&gmac0>;
|
|
phy-mode = "2500base-x";
|
|
|
|
fixed-link {
|
|
speed = <2500>;
|
|
full-duplex;
|
|
pause;
|
|
};
|
|
};
|
|
};
|
|
};
|
|
|
|
&usb_phy {
|
|
status = "okay";
|
|
};
|
|
|
|
&xhci {
|
|
mediatek,u3p-dis-msk = <0x0>;
|
|
phys = <&u2port0 PHY_TYPE_USB2>,
|
|
<&u3port0 PHY_TYPE_USB3>;
|
|
status = "okay";
|
|
};
|