mirror of
https://github.com/openwrt/openwrt.git
synced 2024-12-20 06:08:08 +00:00
4c0c860846
INABA Abaniact AML2-17GP is a 17 port gigabit switch, based on RTL8382.
Specification:
- SoC : Realtek RTL8382
- RAM : DDR3 128 MiB (SK hynix H5TQ1G63EFR)
- Flash : SPI-NOR 32 MiB (Macronix MX25L25635FZ2I-10G)
- Ethernet : 10/100/1000 Mbps x17
- port 1-8 : RTL8218B (SoC)
- port 8-16 : RTL8218D
- port wan : RTL8214FC
- LEDs/Keys : 1x, 1x
- UART : pin header on PCB (Molex 530470410 compatible)
- J14: 3.3V, GND, RX, TX from rear side
- 115200n8
- Power : 100-240 VAC, 50/60 Hz, 0.21 A
- Plug : IEC 60320-C13
Flash instruction using initramfs image:
1. Boot AML2-17GP normally
2. Set the IP address of computer to the range of 192.168.1.0/24, other
than 192.168.1.248 and connect computer to "WAN/CONSOLE" port of
AML2-17GP
3. Access to "http://192.168.1.248" and open firmware setting page
-- UI Language: 日本語 --
"メンテナンス" -> "デュアルイメージ"
-- UI Language: ENGLISH --
"Maintenance" -> "Dual Image"
4. Check "イメージ情報 (en: "Images Information")" and set the first
image to active by choosing "アクティブイメージ" (en: "Active
Image") in the partition "0"
5. open firmware upgrade page
-- UI Language: 日本語 --
"メンテナンス" -> "アップグレードマネージャー"
-- UI Language: ENGLISH --
"Maintenance" -> "Upgrade Manager"
6. Set the properties as follows
-- UI Language: 日本語 --
"アップグレード方式" : "HTTP"
"アップグレードタイプ" : "イメージ"
"イメージ" : "アクティブ"
"ブラウズファイル" : (select the OpenWrt initramfs image)
-- UI Language: ENGLISH --
"Upgrade Method" : "HTTP"
"Upgrade Type" : "Image"
"Image" : "(Active)"
"Browse file" : (select the OpenWrt initramfs image)
7. Press "アップグレード" (en: "Upgrade") button and perform upgrade
8. Wait ~150 seconds to complete flashing
9. After the flashing, the following message is showed and press "OK"
button to reboot
-- UI Language: 日本語 --
"成功!! 今すぐリブートしますか?"
-- UI Language: ENGLISH --
"Success!! Do you want to reboot now?"
10. After the rebooting, reconnect the cable to other port (1-16) and
open the SSH connection, download the sysupgrade image to the device
and perform sysupgrade with it
11. Wait ~120 seconds to complete sysupgrade
Note:
- The uploaded image via WebUI will only be written with the length
embedded in the uImage header. If the sysupgrade image is specified,
only the kernel is flashed and lacks the rootfs, this causes a kernel
panic while booting and bootloops.
To avoid this issue, initramfs image is required for flashing on WebUI
of stock firmware.
- This device has 1x LED named as "POWER", but it's not connected to the
GPIO of SoC and cannot be controlled.
- port 17 is named as "WAN/CONSOLE". This port is for the upstream
connection and console access (telnet/WebUI) on stock firmware.
Back to stock firmware:
1. Set "bootpartition" variable in u-boot-env2 partition to "1" by
fw_setsys
fw_setsys bootpartition 1
2. Reboot AML2-17GP
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
157 lines
3.6 KiB
Makefile
157 lines
3.6 KiB
Makefile
# SPDX-License-Identifier: GPL-2.0-only
|
|
|
|
include $(TOPDIR)/rules.mk
|
|
include $(INCLUDE_DIR)/image.mk
|
|
|
|
KERNEL_LOADADDR = 0x80000000
|
|
KERNEL_ENTRY = 0x80000400
|
|
|
|
DEVICE_VARS += ZYXEL_VERS
|
|
|
|
define Build/zyxel-vers
|
|
( echo VERS;\
|
|
for hw in $(1); do\
|
|
echo -n "V9.99($$hw.0) | ";\
|
|
date -d @$(SOURCE_DATE_EPOCH) +%m/%d/%Y;\
|
|
done ) >> $@
|
|
endef
|
|
|
|
define Device/Default
|
|
PROFILES = Default
|
|
KERNEL := kernel-bin | append-dtb | gzip | uImage gzip
|
|
KERNEL_INITRAMFS := kernel-bin | append-dtb | gzip | uImage gzip
|
|
DEVICE_DTS_DIR := ../dts
|
|
DEVICE_DTS = $$(SOC)_$(1)
|
|
IMAGES := sysupgrade.bin
|
|
IMAGE/sysupgrade.bin := append-kernel | pad-to 64k | append-rootfs | pad-rootfs | \
|
|
append-metadata | check-size
|
|
endef
|
|
|
|
# "NGE" refers to the uImage magic
|
|
define Device/netgear_nge
|
|
KERNEL := kernel-bin | append-dtb | lzma | uImage lzma
|
|
KERNEL_INITRAMFS := kernel-bin | append-dtb | lzma | uImage lzma
|
|
SOC := rtl8380
|
|
IMAGE_SIZE := 14848k
|
|
UIMAGE_MAGIC := 0x4e474520
|
|
DEVICE_VENDOR := NETGEAR
|
|
endef
|
|
|
|
define Device/allnet_all-sg8208m
|
|
SOC := rtl8382
|
|
IMAGE_SIZE := 7168k
|
|
DEVICE_VENDOR := ALLNET
|
|
DEVICE_MODEL := ALL-SG8208M
|
|
UIMAGE_MAGIC := 0x00000006
|
|
UIMAGE_NAME := 2.2.2.0
|
|
endef
|
|
TARGET_DEVICES += allnet_all-sg8208m
|
|
|
|
define Device/d-link_dgs-1210
|
|
SOC := rtl8382
|
|
IMAGE_SIZE := 13824k
|
|
DEVICE_VENDOR := D-Link
|
|
endef
|
|
|
|
define Device/d-link_dgs-1210-10p
|
|
$(Device/d-link_dgs-1210)
|
|
DEVICE_MODEL := DGS-1210-10P
|
|
DEVICE_PACKAGES += lua-rs232
|
|
endef
|
|
TARGET_DEVICES += d-link_dgs-1210-10p
|
|
|
|
define Device/d-link_dgs-1210-16
|
|
$(Device/d-link_dgs-1210)
|
|
DEVICE_MODEL := DGS-1210-16
|
|
endef
|
|
TARGET_DEVICES += d-link_dgs-1210-16
|
|
|
|
define Device/d-link_dgs-1210-28
|
|
$(Device/d-link_dgs-1210)
|
|
DEVICE_MODEL := DGS-1210-28
|
|
endef
|
|
TARGET_DEVICES += d-link_dgs-1210-28
|
|
|
|
define Device/inaba_aml2-17gp
|
|
SOC := rtl8382
|
|
IMAGE_SIZE := 13504k
|
|
DEVICE_VENDOR := INABA
|
|
DEVICE_MODEL := Abaniact AML2-17GP
|
|
UIMAGE_MAGIC := 0x83800000
|
|
endef
|
|
TARGET_DEVICES += inaba_aml2-17gp
|
|
|
|
define Device/netgear_gs108t-v3
|
|
$(Device/netgear_nge)
|
|
DEVICE_MODEL := GS108T
|
|
DEVICE_VARIANT := v3
|
|
endef
|
|
TARGET_DEVICES += netgear_gs108t-v3
|
|
|
|
define Device/netgear_gs110tpp-v1
|
|
$(Device/netgear_nge)
|
|
DEVICE_MODEL := GS110TPP
|
|
DEVICE_VARIANT := v1
|
|
endef
|
|
TARGET_DEVICES += netgear_gs110tpp-v1
|
|
|
|
define Device/netgear_gs308t-v1
|
|
$(Device/netgear_nge)
|
|
DEVICE_MODEL := GS308T
|
|
DEVICE_VARIANT := v1
|
|
UIMAGE_MAGIC := 0x4e474335
|
|
endef
|
|
TARGET_DEVICES += netgear_gs308t-v1
|
|
|
|
define Device/netgear_gs310tp-v1
|
|
$(Device/netgear_nge)
|
|
DEVICE_MODEL := GS310TP
|
|
DEVICE_VARIANT := v1
|
|
UIMAGE_MAGIC := 0x4e474335
|
|
DEVICE_PACKAGES += lua-rs232
|
|
endef
|
|
TARGET_DEVICES += netgear_gs310tp-v1
|
|
|
|
define Device/zyxel_gs1900
|
|
SOC := rtl8380
|
|
IMAGE_SIZE := 6976k
|
|
DEVICE_VENDOR := ZyXEL
|
|
UIMAGE_MAGIC := 0x83800000
|
|
KERNEL_INITRAMFS := kernel-bin | append-dtb | gzip | zyxel-vers $$$$(ZYXEL_VERS) | \
|
|
uImage gzip
|
|
endef
|
|
|
|
define Device/zyxel_gs1900-10hp
|
|
$(Device/zyxel_gs1900)
|
|
DEVICE_MODEL := GS1900-10HP
|
|
ZYXEL_VERS := AAZI
|
|
endef
|
|
TARGET_DEVICES += zyxel_gs1900-10hp
|
|
|
|
define Device/zyxel_gs1900-8
|
|
$(Device/zyxel_gs1900)
|
|
DEVICE_MODEL := GS1900-8
|
|
ZYXEL_VERS := AAHH
|
|
endef
|
|
TARGET_DEVICES += zyxel_gs1900-8
|
|
|
|
define Device/zyxel_gs1900-8hp-v1
|
|
$(Device/zyxel_gs1900)
|
|
DEVICE_MODEL := GS1900-8HP
|
|
DEVICE_VARIANT := v1
|
|
ZYXEL_VERS := AAHI
|
|
DEVICE_PACKAGES += lua-rs232
|
|
endef
|
|
TARGET_DEVICES += zyxel_gs1900-8hp-v1
|
|
|
|
define Device/zyxel_gs1900-8hp-v2
|
|
$(Device/zyxel_gs1900)
|
|
DEVICE_MODEL := GS1900-8HP
|
|
DEVICE_VARIANT := v2
|
|
ZYXEL_VERS := AAHI
|
|
DEVICE_PACKAGES += lua-rs232
|
|
endef
|
|
TARGET_DEVICES += zyxel_gs1900-8hp-v2
|
|
|
|
$(eval $(call BuildImage))
|