ExternalVendorCode/openwrt
1
0
Fork 0
mirror of https://github.com/openwrt/openwrt.git synced 2024-12-23 15:32:33 +00:00
Code Issues Actions 7 Packages Projects Releases Wiki Activity
4b89b90d9f
openwrt/target/linux/bcm53xx/image/Makefile
Vivek Unune 9aaa20d8ba bcm53xx: enhance support for Linksys EA9500 
1. Add leds and configs
2. Add network configs
3. Add script to clear partial boot flag
4. Hack to use port 5 as cpu port as port 8 connected to eth2
   wont pass any frames
5. Enable EA9500 image generation

Hardware Info:

- Processor - Broadcom BCM4709C0KFEBG dual-core @ 1.4 GHz
- Switch - BCM53012 in BCM4709C0KFEBG & external BCM53125
- DDR3 RAM - 256 MB
- Flash - 128 MB (Toshiba TC58BVG0S3HTA00)
- 2.4GHz - BCM4366 4×4 2.4/5G single chip 802.11ac SoC
- Power Amp - Skyworks SE2623L 2.4 GHz power amp (x4)
- 5GHz x 2 - BCM4366 4×4 2.4/5G single chip 802.11ac SoC
- Power Amp - PLX Technology PEX8603 3-lane, 3-port PCIe switch
- Ports - 8 Ports, 1 WAN Ports
- Antennas - 8 Antennas
- Serial Port - @j6 [GND,TX,RX] (VCC NC) 115200 8n1

Flashing Instructions:

1. Connect a USB-TTL table to J6 on the router as well as a
   ethernet cable to a lan port and your PC.
2. Power-on the router.
3. Use putty or a serial port program to view the terminal.
   Hit Ctrl+C and interrupt the CFE terminal terminal.
4. Setup a TFTP server on your local machine at setup you
   local IP to 192.168.1.2
5. Start the TFTP Server
6. Run following commands at the CFE terminal

   flash -noheader 192.168.1.2:/openwrt.trx nflash0.trx
   flash -noheader 192.168.1.2:/openwrt.trx nflash0.trx2
   nvram set bootpartition=0 && nvram set partialboots=0 && nvram commit

7. Reboot router to be presented by OpenWrt

Note: Only installation method via serial cable is supported at the moment.
The trx firmware has to be flashed to both the partitions using following
commands from CFE prompt. This will cover US and Non-US variants.

Signed-off-by: Vivek Unune <npcomplete13@gmail.com>
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
(cherry picked from commit 209c5918b5)
2021-04-08 12:49:01 +02:00

455 lines
12 KiB
Makefile
Raw Blame History

# SPDX-License-Identifier: GPL-2.0-only
#
# Copyright (C) 2013 OpenWrt.org
include $(TOPDIR)/rules.mk
include $(INCLUDE_DIR)/image.mk
define Image/Prepare
rm -f $(KDIR)/fs_mark
echo -ne '\xde\xad\xc0\xde' > $(KDIR)/fs_mark
$(call prepare_generic_squashfs,$(KDIR)/fs_mark)
# For UBI we want only one extra block
rm -f $(KDIR)/ubi_mark
echo -ne '\xde\xad\xc0\xde' > $(KDIR)/ubi_mark
endef
define Build/lzma-d16
$(STAGING_DIR_HOST)/bin/lzma e $@ -d16 $(1) $@.new
mv $@.new $@
endef
# Similar to Build/tplink-safeloader but uses TRX instead of clean kernel
define Build/bcm53xx-tplink-safeloader
$(STAGING_DIR_HOST)/bin/trx \
-o $@.trx \
-m 33554432 \
-f $(IMAGE_KERNEL) -a 1024
$(STAGING_DIR_HOST)/bin/tplink-safeloader \
-B $(TPLINK_BOARD) \
-k $@.trx \
-r $@ \
-j \
-o $@.new
mv $@.new $@
rm $@.trx
endef
define Build/buffalo-wzr-header
$(eval product=$(word 1,$(1)))
$(eval region=$(word 2,$(1)))
( \
echo $(product)_$(BUFFALO_TAG_VERSION)_$(BUFFALO_TAG_MINOR)_$(region)_$(BUFFALO_TAG_PLATFORM); \
echo filelen=$$(stat -c%s $@); \
cat $@ \
) > $@.new
mv $@.new $@
endef
# TRX with only one (kernel) partition
define Build/trx
$(STAGING_DIR_HOST)/bin/trx \
-o $@.new \
-m 33554432 \
-f $@
mv $@.new $@
endef
define Build/trx-serial
$(STAGING_DIR_HOST)/bin/otrx create $@.new \
-f $(IMAGE_KERNEL) -a 1024 \
-f $@ -a 0x10000 -A $(KDIR)/fs_mark
mv $@.new $@
endef
define Build/trx-nand
# kernel: always use 4 MiB (-28 B or TRX header) to allow upgrades even
# if it grows up between releases
# root: UBI with one extra block containing UBI mark to trigger erasing
# rest of partition
$(STAGING_DIR_HOST)/bin/otrx create $@.new \
-f $(IMAGE_KERNEL) -a 0x20000 -b 0x400000 \
-f $@ \
-A $(KDIR)/ubi_mark -a 0x20000
mv $@.new $@
endef
define Build/asus-trx
$(STAGING_DIR_HOST)/bin/asustrx \
-p $(ASUS_PRODUCTID) -i $@ -o $@.new
mv $@.new $@
endef
define Build/luxul-lxl
$(STAGING_DIR_HOST)/bin/lxlfw create $@.new \
-i $@ \
-b $(LUXUL_BOARD)
mv $@.new $@
endef
define Build/seama-nand
# Seama entity
$(STAGING_DIR_HOST)/bin/oseama \
entity $@.entity \
-m "dev=/dev/mtdblock/7" \
-m "type=firmware" \
-f $(IMAGE_KERNEL) \
-b 0x400000 \
-f $@ \
-f $(KDIR)/ubi_mark
# Seama container
$(STAGING_DIR_HOST)/bin/seama \
-s $@ \
-m "signature=$(SIGNATURE)" \
-i $@.entity
endef
DEVICE_VARS += ASUS_PRODUCTID
DEVICE_VARS += BUFFALO_TAG_PLATFORM BUFFALO_TAG_VERSION BUFFALO_TAG_MINOR
DEVICE_VARS += SIGNATURE
DEVICE_VARS += NETGEAR_BOARD_ID NETGEAR_REGION TPLINK_BOARD
DEVICE_VARS += LUXUL_BOARD
IEEE8021X := wpad-basic-wolfssl
B43 := $(IEEE8021X) kmod-b43
BRCMFMAC_43602A1 := $(IEEE8021X) kmod-brcmfmac brcmfmac-firmware-43602a1-pcie
BRCMFMAC_4366B1 := $(IEEE8021X) kmod-brcmfmac brcmfmac-firmware-4366b1-pcie
BRCMFMAC_4366C0 := $(IEEE8021X) kmod-brcmfmac brcmfmac-firmware-4366c0-pcie
USB2_PACKAGES := kmod-usb-ohci kmod-usb2 kmod-phy-bcm-ns-usb2
USB2_PACKAGES += kmod-usb-ledtrig-usbport
USB3_PACKAGES := $(USB2_PACKAGES) kmod-usb3 kmod-phy-bcm-ns-usb3
define Device/Default
# .dtb files are prefixed by SoC type, e.g. bcm4708- which is not included in device/image names
# extract the full dtb name based on the device info
DEVICE_DTS := $(patsubst %.dtb,%,$(notdir $(wildcard $(if $(IB),$(KDIR),$(DTS_DIR))/*-$(subst _,-,$(1)).dtb)))
KERNEL := kernel-bin | append-dtb | lzma-d16
KERNEL_DEPENDS = $$(wildcard $(DTS_DIR)/$$(DEVICE_DTS).dts)
KERNEL_INITRAMFS_SUFFIX := .trx
KERNEL_INITRAMFS := kernel-bin | append-dtb | lzma-d16 | trx
FILESYSTEMS := squashfs
KERNEL_NAME := zImage
IMAGE_NAME = $$(IMAGE_PREFIX)-$$(1).$$(2)
IMAGES := trx
BLOCKSIZE := 128k
PAGESIZE := 2048
IMAGE/trx := append-ubi | trx-nand
endef
define Device/asus
DEVICE_VENDOR := ASUS
IMAGES := trx
IMAGE/trx := append-ubi | trx-nand | asus-trx
endef
define Device/asus_rt-ac56u
$(call Device/asus)
DEVICE_MODEL := RT-AC56U
DEVICE_PACKAGES := $(B43) $(USB3_PACKAGES)
ASUS_PRODUCTID := RT-AC56U
endef
TARGET_DEVICES += asus_rt-ac56u
define Device/asus_rt-ac68u
$(call Device/asus)
DEVICE_MODEL := RT-AC68U
DEVICE_PACKAGES := $(USB3_PACKAGES)
ASUS_PRODUCTID := RT-AC68U
endef
TARGET_DEVICES += asus_rt-ac68u
define Device/asus_rt-ac87u
$(call Device/asus)
DEVICE_MODEL := RT-AC87U
DEVICE_PACKAGES := $(USB3_PACKAGES)
ASUS_PRODUCTID := RT-AC87U
endef
TARGET_DEVICES += asus_rt-ac87u
define Device/asus_rt-n18u
$(call Device/asus)
DEVICE_MODEL := RT-N18U
DEVICE_PACKAGES := $(USB3_PACKAGES)
ASUS_PRODUCTID := RT-N18U
endef
TARGET_DEVICES += asus_rt-n18u
# Buffalo devices have TFTP recovery mode which can work nicely with initramfs
# kernels.
# We should have two initramfs images for Buffalo: plain initramfs kernel and
# TRX with initramfs kernel. It's not possible right now so let's just build
# plain initramfs kernel as it may be more useful.
define Device/buffalo/Default
DEVICE_VENDOR := Buffalo
KERNEL_INITRAMFS_SUFFIX = $$(KERNEL_SUFFIX)
KERNEL_INITRAMFS = $$(KERNEL)
endef
define Device/buffalo_wxr-1900dhp
$(call Device/buffalo/Default)
DEVICE_MODEL := WXR-1900DHP
DEVICE_PACKAGES := $(USB3_PACKAGES)
endef
TARGET_DEVICES += buffalo_wxr-1900dhp
define Device/buffalo_wzr-600dhp2
$(call Device/buffalo/Default)
DEVICE_MODEL := WZR-600DHP2
DEVICE_PACKAGES := $(B43) $(USB2_PACKAGES)
endef
TARGET_DEVICES += buffalo_wzr-600dhp2
define Device/buffalo_wzr-900dhp
$(call Device/buffalo/Default)
DEVICE_MODEL := WZR-900DHP
DEVICE_PACKAGES := $(B43) $(USB3_PACKAGES)
BUFFALO_TAG_PLATFORM := bcm
BUFFALO_TAG_VERSION := 9.99
BUFFALO_TAG_MINOR := 9.99
IMAGES += factory-DHP-EU.bin factory-DHP2-JP.bin
IMAGE/factory-DHP-EU.bin := \
append-ubi | trx-nand | buffalo-wzr-header WZR-900DHP EU | \
buffalo-enc WZR-900DHP $$(BUFFALO_TAG_VERSION) | \
buffalo-tag-dhp WZR-900DHP EU mlang20 | buffalo-enc-tag | \
buffalo-dhp-image
IMAGE/factory-DHP2-JP.bin := \
append-ubi | trx-nand | buffalo-wzr-header WZR-900DHP2 JP | \
buffalo-enc WZR-900DHP2 $$(BUFFALO_TAG_VERSION) | \
buffalo-tag-dhp WZR-900DHP2 JP jp | buffalo-enc-tag | \
buffalo-dhp-image
endef
TARGET_DEVICES += buffalo_wzr-900dhp
define Device/buffalo_wzr-1750dhp
$(call Device/buffalo/Default)
DEVICE_MODEL := WZR-1750DHP
DEVICE_PACKAGES := $(B43) $(USB3_PACKAGES)
endef
TARGET_DEVICES += buffalo_wzr-1750dhp
define Device/dlink
DEVICE_VENDOR := D-Link
IMAGES := bin
IMAGE/bin := append-ubi | seama-nand
endef
define Device/dlink_dir-885l
DEVICE_MODEL := DIR-885L
DEVICE_PACKAGES := $(BRCMFMAC_4366B1) $(USB3_PACKAGES)
$(Device/dlink)
SIGNATURE := wrgac42_dlink.2015_dir885l
endef
TARGET_DEVICES += dlink_dir-885l
# Linksys devices are disabled due to problem with 2 TRX partitions
define Device/linksys_ea6300-v1
DEVICE_VENDOR := Linksys
DEVICE_MODEL := EA6300
DEVICE_VARIANT := v1
DEVICE_PACKAGES := $(B43) $(USB3_PACKAGES)
BROKEN := y
endef
TARGET_DEVICES += linksys_ea6300-v1
define Device/linksys_ea6500-v2
DEVICE_VENDOR := Linksys
DEVICE_MODEL := EA6500
DEVICE_VARIANT := v2
DEVICE_PACKAGES := $(B43) $(USB3_PACKAGES)
endef
TARGET_DEVICES += linksys_ea6500-v2
define Device/linksys_ea9200
DEVICE_VENDOR := Linksys
DEVICE_MODEL := EA9200
DEVICE_VARIANT := v1
DEVICE_PACKAGES := $(BRCMFMAC_43602A1) $(USB3_PACKAGES)
BROKEN := y
endef
TARGET_DEVICES += linksys_ea9200
define Device/linksys_ea9500
DEVICE_VENDOR := Linksys
DEVICE_MODEL := EA9500
DEVICE_PACKAGES := $(BRCMFMAC_4366C0) $(USB3_PACKAGES)
DEVICE_DTS := bcm47094-linksys-panamera
endef
TARGET_DEVICES += linksys_ea9500
define Device/luxul
DEVICE_VENDOR := Luxul
IMAGES := lxl
IMAGE/lxl := append-ubi | trx-nand | luxul-lxl
endef
define Device/luxul_abr-4500
$(Device/luxul)
DEVICE_MODEL := ABR-4500
DEVICE_PACKAGES := $(USB3_PACKAGES)
LUXUL_BOARD := ABR-4500
endef
TARGET_DEVICES += luxul_abr-4500
define Device/luxul_xap-1610
$(Device/luxul)
DEVICE_MODEL := XAP-1610
DEVICE_PACKAGES := $(BRCMFMAC_4366C0)
IMAGE/lxl := append-rootfs | trx-serial | luxul-lxl
LUXUL_BOARD := XAP-1610
endef
TARGET_DEVICES += luxul_xap-1610
define Device/luxul_xbr-4500
$(Device/luxul)
DEVICE_MODEL := XBR-4500
DEVICE_PACKAGES := $(USB3_PACKAGES)
LUXUL_BOARD := XBR-4500
endef
TARGET_DEVICES += luxul_xbr-4500
define Device/luxul_xwr-3150
$(Device/luxul)
DEVICE_MODEL := XWR-3150
DEVICE_PACKAGES := $(BRCMFMAC_4366C0) $(USB3_PACKAGES)
DEVICE_DTS := bcm47094-luxul-xwr-3150-v1
LUXUL_BOARD := XWR-3150
endef
TARGET_DEVICES += luxul_xwr-3150
define Device/meraki_mr32
DEVICE_VENDOR := Meraki
DEVICE_MODEL := MR32
DEVICE_PACKAGES := $(B43) kmod-i2c-bcm-iproc kmod-i2c-gpio kmod-eeprom-at24 \
kmod-leds-pwm kmod-hwmon-ina2xx kmod-bluetooth
DEVICE_DTS := bcm53016-meraki-mr32
# Meraki FW r23 tries to resize the part.safe partition before it will
# flash the image. This is a bit of a problem, since resizing will fail
# if the partition is smaller than the old one.
KERNEL_LOADADDR := 0x00008000
KERNEL_INITRAMFS_SUFFIX := .bin
KERNEL_INITRAMFS := kernel-bin | fit none $$(DTS_DIR)/$$(DEVICE_DTS).dtb | \
pad-to 10362880
KERNEL := kernel-bin | fit none $$(DTS_DIR)/$$(DEVICE_DTS).dtb
IMAGES := sysupgrade.bin
# Currently the only device that uses the new image check
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
# The loader is specifically looking for fdt@2:
# [ 3.190000] find_itb_subimage: error finding fdt@2: FDT_ERR_NOTFOUND
# The image won't boot, if it isn't found. :(
DEVICE_FDT_NUM := 2
endef
TARGET_DEVICES += meraki_mr32
define Device/netgear
DEVICE_VENDOR := NETGEAR
IMAGES := chk
IMAGE/chk := append-ubi | trx-nand | netgear-chk
NETGEAR_REGION := 1
endef
define Device/netgear_r6250
DEVICE_MODEL := R6250
DEVICE_PACKAGES := $(B43) $(USB3_PACKAGES)
$(Device/netgear)
NETGEAR_BOARD_ID := U12H245T00_NETGEAR
endef
TARGET_DEVICES += netgear_r6250
define Device/netgear_r6300-v2
DEVICE_MODEL := R6300
DEVICE_VARIANT := v2
DEVICE_PACKAGES := $(B43) $(USB3_PACKAGES)
$(Device/netgear)
NETGEAR_BOARD_ID := U12H240T00_NETGEAR
endef
TARGET_DEVICES += netgear_r6300-v2
define Device/netgear_r7000
DEVICE_MODEL := R7000
DEVICE_PACKAGES := $(USB3_PACKAGES)
$(Device/netgear)
NETGEAR_BOARD_ID := U12H270T00_NETGEAR
endef
TARGET_DEVICES += netgear_r7000
define Device/netgear_r7900
DEVICE_MODEL := R7900
DEVICE_PACKAGES := $(BRCMFMAC_43602A1) $(USB3_PACKAGES)
$(Device/netgear)
NETGEAR_BOARD_ID := U12H315T30_NETGEAR
endef
TARGET_DEVICES += netgear_r7900
define Device/netgear_r8000
DEVICE_MODEL := R8000
DEVICE_PACKAGES := $(BRCMFMAC_43602A1) $(USB3_PACKAGES)
$(Device/netgear)
NETGEAR_BOARD_ID := U12H315T00_NETGEAR
endef
TARGET_DEVICES += netgear_r8000
define Device/netgear_r8500
DEVICE_MODEL := R8500
DEVICE_PACKAGES := $(BRCMFMAC_4366B1) $(USB3_PACKAGES)
$(Device/netgear)
NETGEAR_BOARD_ID := U12H334T00_NETGEAR
DEFAULT := n
endef
TARGET_DEVICES += netgear_r8500
define Device/smartrg_sr400ac
DEVICE_VENDOR := SmartRG
DEVICE_MODEL := SR400ac
DEVICE_PACKAGES := $(BRCMFMAC_43602A1) $(USB3_PACKAGES)
IMAGES := trx
IMAGE/trx := append-rootfs | trx-serial
KERNEL_INITRAMFS_SUFFIX := .bin
KERNEL_INITRAMFS := kernel-bin | append-dtb | lzma-d16
endef
TARGET_DEVICES += smartrg_sr400ac
define Device/phicomm_k3
DEVICE_VENDOR := PHICOMM
DEVICE_MODEL := K3
DEVICE_PACKAGES := $(BRCMFMAC_4366C0) $(USB3_PACKAGES)
IMAGES := trx
endef
TARGET_DEVICES += phicomm_k3
define Device/tenda_ac9
DEVICE_VENDOR := Tenda
DEVICE_MODEL := AC9
DEVICE_PACKAGES := $(B43) $(USB2_PACKAGES)
IMAGES := trx
IMAGE/trx := append-rootfs | trx-serial
endef
TARGET_DEVICES += tenda_ac9
define Device/tplink_archer-c5-v2
DEVICE_VENDOR := TP-Link
DEVICE_MODEL := Archer C5
DEVICE_VARIANT := v2
DEVICE_PACKAGES := $(B43) $(USB2_PACKAGES)
IMAGES := bin
IMAGE/bin := append-rootfs | bcm53xx-tplink-safeloader
TPLINK_BOARD := ARCHER-C5-V2
BROKEN := y
endef
TARGET_DEVICES += tplink_archer-c5-v2
define Device/tplink_archer-c9-v1
DEVICE_VENDOR := TP-Link
DEVICE_MODEL := Archer C9
DEVICE_VARIANT := v1
DEVICE_PACKAGES := $(USB3_PACKAGES)
IMAGES := bin
IMAGE/bin := append-rootfs | bcm53xx-tplink-safeloader
TPLINK_BOARD := ARCHERC9
BROKEN := y
endef
TARGET_DEVICES += tplink_archer-c9-v1
$(eval $(call BuildImage))
Reference in New Issue View Git Blame Copy Permalink