mirror of
https://github.com/openwrt/openwrt.git
synced 2024-12-23 07:22:33 +00:00
49ed52b862
Use nvmem-layout in device tree instead of extracting MAC addresses in userspace. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
206 lines
3.4 KiB
Plaintext
206 lines
3.4 KiB
Plaintext
// SPDX-License-Identifier: (GPL-2.0 OR MIT)
|
|
|
|
/dts-v1/;
|
|
#include "mt7981.dtsi"
|
|
|
|
/ {
|
|
model = "GL.iNet GL-MT2500";
|
|
compatible = "glinet,gl-mt2500", "mediatek,mt7981";
|
|
|
|
aliases {
|
|
label-mac-device = &gmac0;
|
|
led-boot = &led_sys_white;
|
|
led-failsafe = &led_sys_blue;
|
|
led-running = &led_sys_white;
|
|
led-upgrade = &led_sys_blue;
|
|
serial0 = &uart0;
|
|
};
|
|
|
|
chosen {
|
|
stdout-path = "serial0:115200n8";
|
|
bootargs-append = " root=PARTLABEL=rootfs rootwait";
|
|
};
|
|
|
|
gpio-keys {
|
|
compatible = "gpio-keys";
|
|
|
|
reset {
|
|
label = "reset";
|
|
linux,code = <KEY_RESTART>;
|
|
gpios = <&pio 1 GPIO_ACTIVE_LOW>;
|
|
};
|
|
};
|
|
|
|
leds {
|
|
compatible = "gpio-leds";
|
|
|
|
led-vpn {
|
|
label = "white:vpn";
|
|
gpios = <&pio 31 GPIO_ACTIVE_LOW>;
|
|
};
|
|
|
|
led_sys_white: led-system-white {
|
|
label = "white:system";
|
|
gpios = <&pio 30 GPIO_ACTIVE_LOW>;
|
|
};
|
|
|
|
led_sys_blue: led-system-blue {
|
|
label = "blue:system";
|
|
gpios = <&pio 29 GPIO_ACTIVE_LOW>;
|
|
};
|
|
};
|
|
|
|
usb_vbus: regulstor-usb {
|
|
compatible = "regulator-fixed";
|
|
|
|
regulator-name = "usb-vbus";
|
|
regulator-min-microvolt = <5000000>;
|
|
regulator-max-microvolt = <5000000>;
|
|
|
|
gpio = <&pio 12 GPIO_ACTIVE_HIGH>;
|
|
enable-active-high;
|
|
regulator-boot-on;
|
|
};
|
|
|
|
reg_3p3v: regulator-3p3v {
|
|
compatible = "regulator-fixed";
|
|
regulator-name = "fixed-3.3V";
|
|
regulator-min-microvolt = <3300000>;
|
|
regulator-max-microvolt = <3300000>;
|
|
regulator-boot-on;
|
|
regulator-always-on;
|
|
};
|
|
};
|
|
|
|
&pio {
|
|
mmc0_pins_default: mmc0-pins-default {
|
|
mux {
|
|
function = "flash";
|
|
groups = "emmc_45";
|
|
};
|
|
};
|
|
mmc0_pins_uhs: mmc0-pins-uhs {
|
|
mux {
|
|
function = "flash";
|
|
groups = "emmc_45";
|
|
};
|
|
};
|
|
};
|
|
|
|
&uart0 {
|
|
status = "okay";
|
|
};
|
|
|
|
&watchdog {
|
|
status = "okay";
|
|
};
|
|
|
|
ð {
|
|
status = "okay";
|
|
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&mdio_pins>;
|
|
|
|
gmac0: mac@0 {
|
|
compatible = "mediatek,eth-mac";
|
|
nvmem-cells = <&macaddr_boot1_a 0>;
|
|
nvmem-cell-names = "mac-address";
|
|
reg = <0>;
|
|
|
|
phy-mode = "2500base-x";
|
|
phy-handle = <&phy5>;
|
|
};
|
|
|
|
gmac1: mac@1 {
|
|
compatible = "mediatek,eth-mac";
|
|
nvmem-cells = <&macaddr_boot1_a 1>;
|
|
nvmem-cell-names = "mac-address";
|
|
reg = <1>;
|
|
phy-mode = "gmii";
|
|
phy-handle = <&int_gbe_phy>;
|
|
};
|
|
};
|
|
|
|
&mdio_bus {
|
|
reset-gpios = <&pio 14 GPIO_ACTIVE_LOW>;
|
|
reset-delay-us = <600>;
|
|
reset-post-delay-us = <20000>;
|
|
|
|
phy5: ethernet-phy@5 {
|
|
reg = <5>;
|
|
compatible = "ethernet-phy-ieee802.3-c45";
|
|
};
|
|
};
|
|
|
|
&usb_phy {
|
|
status = "okay";
|
|
};
|
|
|
|
&xhci {
|
|
status = "okay";
|
|
vbus-supply = <&usb_vbus>;
|
|
};
|
|
|
|
&mmc0 {
|
|
status = "okay";
|
|
|
|
pinctrl-names = "default", "state_uhs";
|
|
pinctrl-0 = <&mmc0_pins_default>;
|
|
pinctrl-1 = <&mmc0_pins_uhs>;
|
|
bus-width = <8>;
|
|
max-frequency = <52000000>;
|
|
vmmc-supply = <®_3p3v>;
|
|
cap-mmc-highspeed;
|
|
non-removable;
|
|
|
|
card@0 {
|
|
compatible = "mmc-card";
|
|
reg = <0>;
|
|
|
|
block {
|
|
compatible = "block-device";
|
|
|
|
partitions {
|
|
block-partition-u-boot-env {
|
|
partname = "u-boot-env";
|
|
nvmem-layout {
|
|
compatible = "u-boot,env-layout";
|
|
};
|
|
};
|
|
};
|
|
};
|
|
|
|
boot1 {
|
|
compatible = "block-device";
|
|
|
|
nvmem-layout {
|
|
compatible = "fixed-layout";
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
|
|
macaddr_boot1_a: macaddr@a {
|
|
compatible = "mac-base";
|
|
reg = <0xa 0x6>;
|
|
#nvmem-cell-cells = <1>;
|
|
};
|
|
|
|
ddns_boot1_10@10 {
|
|
reg = <0x10 0x10>;
|
|
};
|
|
|
|
sn_bak_boot1_20@20 {
|
|
reg = <0x20 0x10>;
|
|
};
|
|
|
|
sn_boot1_20@30 {
|
|
reg = <0x30 0x10>;
|
|
};
|
|
|
|
country_code_boot1_88@88 {
|
|
reg = <0x88 0x10>;
|
|
};
|
|
};
|
|
};
|
|
};
|
|
};
|