mirror of
https://github.com/openwrt/openwrt.git
synced 2024-12-29 01:59:02 +00:00
b893aa7992
Linksys E5400 is a 2.4/5GHz dual band AC router, based on MediaTek MT7628AN. This device is also sold as Linksys E2500v4, E5300 and E5350 with the same hardware, but software speed limitations in vendor firmwares. Specification: * SoC: MT7628AN (580 MHz) * RAM: DDR2 64 MiB * Flash: 16 MiB NOR (W25Q128BV) * Wi-Fi: * 2.4GHz: SoC Built-in * 5GHz: MT7612EN * Ethernet: 5x 100Mbps * Switch: SoC built-in * UART: * 115200, 8N1, 3.3V (real u-boot speed: 119050) * Pinout JB4: 1:[3V3] (TXD) (RXD) [NC] (GND) Flash Layout: 0x0000000-0x0030000 : "Bootloader" 0x0030000-0x0040000 : "Config" 0x0040000-0x0050000 : "Factory" 0x0050000-0x0ff0000 : "Kernel" 0x0ff0000-0x1000000 : "CBTinfo" MAC address: LAN: factory 0x28 WAN: LAN + 1 2.4G: LAN + 2 5G: LAN + 3 Installation: 1. Connect to UART, use LF as EOL (not CRLF) 2. Set IP address - Press 4 during boot - setenv serverip <TFTPSERVER_IP> - setenv ipaddr <DEVICE_IP> - setenv bootfile openwrt-ramips-mt76x8-linksys_e5400-initramfs-kernel.bin - saveenv - reset 3. Load Openwrt Kernel image from TFTP: - Press 1 during boot - IP and filename should be already set 4. Boot into OpenWrt and perform sysupgrade with sysupgrade image. Signed-off-by: Julien Dusser <julien.dusser@free.fr>
164 lines
2.6 KiB
Plaintext
164 lines
2.6 KiB
Plaintext
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
|
|
|
#include "mt7628an.dtsi"
|
|
|
|
#include <dt-bindings/gpio/gpio.h>
|
|
#include <dt-bindings/input/input.h>
|
|
|
|
/ {
|
|
compatible = "linksys,e5400", "mediatek,mt7628an-soc";
|
|
model = "Linksys E5400";
|
|
|
|
aliases {
|
|
led-boot = &led_wps;
|
|
led-failsafe = &led_wps;
|
|
led-running = &led_wps;
|
|
led-upgrade = &led_wps;
|
|
label-mac-device = ðernet;
|
|
};
|
|
|
|
chosen {
|
|
bootargs = "console=ttyS0,115200";
|
|
};
|
|
|
|
memory@0 {
|
|
device_type = "memory";
|
|
reg = <0x0 0x4000000>;
|
|
};
|
|
|
|
keys {
|
|
compatible = "gpio-keys";
|
|
|
|
reset {
|
|
label = "reset";
|
|
gpios = <&gpio 11 GPIO_ACTIVE_LOW>;
|
|
linux,code = <KEY_RESTART>;
|
|
};
|
|
|
|
wps {
|
|
label = "wps";
|
|
gpios = <&gpio 38 GPIO_ACTIVE_LOW>;
|
|
linux,code = <KEY_WPS_BUTTON>;
|
|
};
|
|
};
|
|
|
|
leds {
|
|
compatible = "gpio-leds";
|
|
|
|
led_wps: wps {
|
|
label = "green:wps";
|
|
gpios = <&gpio 37 GPIO_ACTIVE_LOW>;
|
|
};
|
|
};
|
|
};
|
|
|
|
&spi0 {
|
|
status = "okay";
|
|
|
|
flash@0 {
|
|
compatible = "jedec,spi-nor";
|
|
reg = <0>;
|
|
spi-max-frequency = <40000000>;
|
|
|
|
partitions {
|
|
compatible = "fixed-partitions";
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
|
|
partition@0 {
|
|
label = "u-boot";
|
|
reg = <0x0 0x30000>;
|
|
read-only;
|
|
};
|
|
|
|
partition@30000 {
|
|
label = "u-boot-env";
|
|
reg = <0x30000 0x10000>;
|
|
read-only;
|
|
};
|
|
|
|
factory: partition@40000 {
|
|
label = "factory";
|
|
reg = <0x40000 0x10000>;
|
|
read-only;
|
|
|
|
compatible = "nvmem-cells";
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
|
|
macaddr_factory_28: macaddr@28 {
|
|
reg = <0x28 0x6>;
|
|
};
|
|
};
|
|
|
|
partition@50000 {
|
|
compatible = "denx,uimage";
|
|
label = "firmware";
|
|
reg = <0x50000 0xfa0000>;
|
|
};
|
|
|
|
partition@ff0000 {
|
|
label = "cbtinfo";
|
|
reg = <0xff0000 0x10000>;
|
|
read-only;
|
|
};
|
|
};
|
|
};
|
|
};
|
|
|
|
&ehci {
|
|
status = "disabled";
|
|
};
|
|
|
|
&esw {
|
|
mediatek,portmap = <0x2f>;
|
|
mediatek,portdisable = <0x20>;
|
|
};
|
|
|
|
ðernet {
|
|
nvmem-cells = <&macaddr_factory_28>;
|
|
nvmem-cell-names = "mac-address";
|
|
};
|
|
|
|
&ohci {
|
|
status = "disabled";
|
|
};
|
|
|
|
&pcie {
|
|
status = "okay";
|
|
};
|
|
|
|
&pcie0 {
|
|
wifi5: wifi@0,0 {
|
|
compatible = "mediatek,mt76";
|
|
reg = <0x0000 0 0 0 0>;
|
|
mediatek,mtd-eeprom = <&factory 0x8000>;
|
|
ieee80211-freq-limit = <5000000 6000000>;
|
|
|
|
nvmem-cells = <&macaddr_factory_28>;
|
|
nvmem-cell-names = "mac-address";
|
|
mac-address-increment = <3>;
|
|
};
|
|
};
|
|
|
|
&state_default {
|
|
gpio {
|
|
group = "gpio", "i2c", "i2s", "refclk", "uart1", "wdt", "wled_an";
|
|
function = "gpio";
|
|
};
|
|
};
|
|
|
|
&usbphy {
|
|
status = "disabled";
|
|
};
|
|
|
|
&wmac {
|
|
status = "okay";
|
|
|
|
mediatek,mtd-eeprom = <&factory 0x0>;
|
|
nvmem-cells = <&macaddr_factory_28>;
|
|
nvmem-cell-names = "mac-address";
|
|
mac-address-increment = <2>;
|
|
};
|
|
|