mirror of
https://github.com/openwrt/openwrt.git
synced 2024-12-27 17:18:59 +00:00
27b2f0fc0f
Iomega Storcenter ix2-200 is a dual SATA NAS powered by a Marvell
Kirkwood SoC clocked at 1GHz. It has 256MB of RAM and 32MB of
flash memory, 3x USB 2.0 and 1x 1Gbit/s NIC
Specification:
- SoC: Marvell Kirkwood 88F6281
- CPU/Speed: 1000Mhz
- Flash-Chip: Hynix NAND
- Flash size: 32 MiB,erase size:16 KiB,page size:512,OOB size:16
- RAM: 256MB
- LAN: 1x 1000 Mbps Ethernet
- WiFi: none
- 3x USB 2.0
- UART: for serial console
Installation instructions - easy steps:
1. download factory.bin and copy into tftp server
2. access uboot environment with serial cable and run
```
setenv mainlineLinux yes
setenv arcNumber 1682
setenv console 'console=ttyS0,115200n8'
setenv mtdparts 'mtdparts=orion_nand:0x100000@0x000000(u-boot)ro,0x20000@0xA0000(u-boot environment)ro,0x300000@0x100000(kernel),0x1C00000@0x400000(ubi)'
setenv bootargs_root 'root='
setenv bootcmd 'setenv bootargs ${console} ${mtdparts} ${bootargs_root}; nand read.e 0x800000 0x100000 0x300000; bootm 0x00800000'
saveenv
setenv serverip 192.168.1.1
setenv ipaddr 192.168.1.13
tftpboot 0x00800000 factory.bin
nand erase 0x100000 $(filesize)
nand write 0x00800000 0x100000 $(filesize)
run bootcmd
```
3. access openwrt by dhcp ip address assigned by your router (p.ex: 192.168.1.13)
Installation steps nand bad blocks proof:
1. download initramfs-uImage and copy into usb ext2 partition
```
mkfs.ext2 -L ext2 /dev/sdh1
mount -t ext2 /dev/sdh1 /mnt
cp initramfs-uImage /mnt/initramfs.bin
umount /mnt
```
2. access uboot environment with serial cable and run
```
setenv mainlineLinux yes
setenv arcNumber 1682
setenv console 'console=ttyS0,115200n8'
setenv mtdparts 'mtdparts=orion_nand:0x100000@0x000000(u-boot)ro,0x20000@0xA0000(u-boot environment)ro,0x300000@0x100000(kernel),0x1C00000@0x400000(ubi)'
setenv bootargs_root 'root='
setenv bootcmd 'setenv bootargs ${console} ${mtdparts} ${bootargs_root}; nand read.e 0x800000 0x100000 0x300000; bootm 0x00800000'
saveenv
usb reset; ext2load usb 0:1 0x00800000 /initramfs.bin; bootm 0x00800000
```
3. log into openwrt and sysupgrade to install into flash
```
sysupgrade -n /tmp/sysupgrade.bin
```
4. access openwrt by dhcp ip address assigned by your router (p.ex: 192.168.1.13)
Signed-off-by: Ademar Arvati Filho <arvati@hotmail.com>
56 lines
873 B
Bash
Executable File
56 lines
873 B
Bash
Executable File
#!/bin/sh
|
|
# Copyright (C) 2014 OpenWrt.org
|
|
|
|
. /lib/functions.sh
|
|
. /lib/functions/leds.sh
|
|
|
|
get_status_led() {
|
|
case $(board_name) in
|
|
cisco,on100)
|
|
status_led="on100:green:health"
|
|
;;
|
|
cloudengines,pogoe02)
|
|
status_led="pogo_e02:orange:fault"
|
|
;;
|
|
cloudengines,pogoplugv4)
|
|
status_led="pogoplugv4:green:health"
|
|
;;
|
|
iom,ix2-200)
|
|
status_led="status:white:power_led"
|
|
;;
|
|
linksys,audi)
|
|
status_led="audi:green:power"
|
|
;;
|
|
linksys,viper)
|
|
status_led="viper:white:health"
|
|
;;
|
|
seagate,dockstar|\
|
|
seagate,goflexhome|\
|
|
seagate,goflexnet)
|
|
status_led="status:orange:fault"
|
|
;;
|
|
zyxel,nsa310b)
|
|
status_led="nsa310:green:sys"
|
|
;;
|
|
esac
|
|
}
|
|
|
|
set_state() {
|
|
get_status_led
|
|
|
|
case "$1" in
|
|
preinit)
|
|
status_led_blink_preinit
|
|
;;
|
|
failsafe)
|
|
status_led_blink_failsafe
|
|
;;
|
|
preinit_regular)
|
|
status_led_blink_preinit_regular
|
|
;;
|
|
done)
|
|
status_led_on
|
|
;;
|
|
esac
|
|
}
|