mirror of
https://github.com/openwrt/openwrt.git
synced 2024-12-22 23:12:32 +00:00
4871fd2616
Device specifications:
* QCA IPQ4019
* 256 MB of RAM
* 32 MB of SPI NOR flash (w25q256)
- 2x 15 MB available; but one of the 15 MB regions is the recovery image
* 2T2R 2.4 GHz
- QCA4019 hw1.0 (SoC)
- requires special BDF in QCA4019/hw1.0/board-2.bin with
bus=ahb,bmi-chip-id=0,bmi-board-id=20,variant=PlasmaCloud-PA2200
* 2T2R 5 GHz (channel 36-64)
- QCA9888 hw2.0 (PCI)
- requires special BDF in QCA9888/hw2.0/board-2.bin
bus=pci,bmi-chip-id=0,bmi-board-id=16,variant=PlasmaCloud-PA2200
* 2T2R 5 GHz (channel 100-165)
- QCA4019 hw1.0 (SoC)
- requires special BDF in QCA4019/hw1.0/board-2.bin with
bus=ahb,bmi-chip-id=0,bmi-board-id=21,variant=PlasmaCloud-PA2200
* GPIO-LEDs for 2.4GHz, 5GHz-SoC and 5GHz-PCIE
* GPIO-LEDs for power (orange) and status (blue)
* 1x GPIO-button (reset)
* TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX)
* 2x gigabit ethernet
- phy@mdio3:
+ Label: Ethernet 1
+ gmac0 (ethaddr) in original firmware
+ used as LAN interface
- phy@mdio4:
+ Label: Ethernet 2
+ gmac1 (eth1addr) in original firmware
+ 802.3at POE+
+ used as WAN interface
* 12V 2A DC
Flashing instructions:
The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
used to transfer the factory image to the u-boot when the device boots up.
Signed-off-by: Marek Lindner <marek.lindner@kaiwoo.ai>
[sven@narfation.org: prepare commit message, rebase, use all LEDs, switch
to dualboot_datachk upgrade script, use eth1 as designated WAN interface]
Signed-off-by: Sven Eckelmann <sven@narfation.org>
130 lines
4.6 KiB
Makefile
130 lines
4.6 KiB
Makefile
include $(TOPDIR)/rules.mk
|
|
include $(INCLUDE_DIR)/version.mk
|
|
|
|
PKG_NAME:=ipq-wifi
|
|
PKG_RELEASE:=1
|
|
PKG_FLAGS:=nonshared
|
|
|
|
include $(INCLUDE_DIR)/package.mk
|
|
|
|
define Build/Prepare
|
|
mkdir -p $(PKG_BUILD_DIR)
|
|
endef
|
|
|
|
define Build/Compile
|
|
endef
|
|
|
|
# Use ath10k-bdencoder from https://github.com/qca/qca-swiss-army-knife.git
|
|
# to generate the board-* files here.
|
|
#
|
|
# This is intended to be used on an interim basis until device-specific
|
|
# board data for new devices is available through the upstream compilation
|
|
#
|
|
# Please send a mail with your device-specific board files upstream.
|
|
# You can find instructions and examples on the linux-wireless wiki:
|
|
# <https://wireless.wiki.kernel.org/en/users/drivers/ath10k/boardfiles>
|
|
|
|
ALLWIFIBOARDS:= \
|
|
8dev_habanero-dvk \
|
|
aruba_ap-303 \
|
|
avm_fritzrepeater-1200 \
|
|
buffalo_wtr-m2133hp \
|
|
cellc_rtl30vw \
|
|
dlink_dap2610 \
|
|
edgecore_ecw5410 \
|
|
edgecore_oap100 \
|
|
engenius_eap2200 \
|
|
engenius_emd1 \
|
|
engenius_emr3500 \
|
|
ezviz_cs-w3-wd1200g-eup \
|
|
glinet_gl-s1300 \
|
|
linksys_ea8300 \
|
|
linksys_mr8300-v0 \
|
|
luma_wrtq-329acn \
|
|
mobipromo_cm520-79f \
|
|
plasmacloud_pa1200 \
|
|
plasmacloud_pa2200 \
|
|
qxwlan_e2600ac
|
|
|
|
ALLWIFIPACKAGES:=$(foreach BOARD,$(ALLWIFIBOARDS),ipq-wifi-$(BOARD))
|
|
|
|
define Package/ipq-wifi-default
|
|
SUBMENU:=ath10k Board-Specific Overrides
|
|
SECTION:=firmware
|
|
CATEGORY:=Firmware
|
|
DEPENDS:=@(TARGET_ipq40xx||TARGET_ipq806x)
|
|
TITLE:=Custom Board
|
|
endef
|
|
|
|
define ipq-wifi-install-one-to
|
|
$(INSTALL_DIR) $(2)/lib/firmware/ath10k/$(3)/
|
|
$(INSTALL_DATA) $(1) $(2)/lib/firmware/ath10k/$(3)/board-2.bin
|
|
endef
|
|
|
|
define ipq-wifi-install-one
|
|
$(if $(filter $(suffix $(1)),.QCA4019 .qca4019),\
|
|
$(call ipq-wifi-install-one-to,$(1),$(2),QCA4019/hw1.0),\
|
|
$(if $(filter $(suffix $(1)),.QCA9888 .qca9888),\
|
|
$(call ipq-wifi-install-one-to,$(1),$(2),QCA9888/hw2.0),\
|
|
$(if $(filter $(suffix $(1)),.QCA9984 .qca9984),\
|
|
$(call ipq-wifi-install-one-to,$(1),$(2),QCA9984/hw1.0),\
|
|
$(error Unrecognized board-file suffix '$(suffix $(1))' for '$(1)')\
|
|
)))
|
|
|
|
endef
|
|
# Blank line required at end of above define due to foreach context
|
|
|
|
define generate-ipq-wifi-package
|
|
define Package/ipq-wifi-$(1)
|
|
$(call Package/ipq-wifi-default)
|
|
TITLE:=board-2.bin Overrides for $(2)
|
|
CONFLICTS:=$(PREV_BOARD)
|
|
endef
|
|
|
|
define Package/ipq-wifi-$(1)/description
|
|
The $(2) requires board-specific, reference ("cal") data
|
|
that is not yet present in the upstream wireless firmware distribution.
|
|
|
|
This package supplies board-2.bin file(s) that, in the interim,
|
|
overwrite those supplied by the ath10k-firmware-* packages.
|
|
|
|
This is package is only necessary for the $(2).
|
|
|
|
Do not install it for any other device!
|
|
endef
|
|
|
|
define Package/ipq-wifi-$(1)/install-overlay
|
|
$$$$(foreach IPQ_WIFI_BOARD_FILE,$$$$(wildcard board-$(1).*),\
|
|
$$$$(call ipq-wifi-install-one,$$$$(IPQ_WIFI_BOARD_FILE),$$(1)))
|
|
endef
|
|
|
|
PREV_BOARD+=ipq-wifi-$(1)
|
|
endef
|
|
|
|
# Add board name to ALLWIFIBOARDS
|
|
# Place files in this directory as board-<devicename>.<qca4019|qca9888|qca9984>
|
|
# Add $(eval $(call generate-ipq-wifi-package,<devicename>,<display name>))
|
|
|
|
$(eval $(call generate-ipq-wifi-package,8dev_habanero-dvk,8devices Habanero DVK))
|
|
$(eval $(call generate-ipq-wifi-package,aruba_ap-303,Aruba AP-303))
|
|
$(eval $(call generate-ipq-wifi-package,avm_fritzrepeater-1200,AVM FRITZRepeater 1200))
|
|
$(eval $(call generate-ipq-wifi-package,buffalo_wtr-m2133hp,Buffalo WTR-M2133HP))
|
|
$(eval $(call generate-ipq-wifi-package,cellc_rtl30vw, Cell C RTL30VW))
|
|
$(eval $(call generate-ipq-wifi-package,dlink_dap2610,D-Link DAP-2610))
|
|
$(eval $(call generate-ipq-wifi-package,edgecore_ecw5410,Edgecore ECW5410))
|
|
$(eval $(call generate-ipq-wifi-package,edgecore_oap100,Edgecore OAP100))
|
|
$(eval $(call generate-ipq-wifi-package,engenius_eap2200,EnGenius EAP2200))
|
|
$(eval $(call generate-ipq-wifi-package,engenius_emd1,EnGenius EMD1))
|
|
$(eval $(call generate-ipq-wifi-package,engenius_emr3500,EnGenius EMR3500))
|
|
$(eval $(call generate-ipq-wifi-package,ezviz_cs-w3-wd1200g-eup,EZVIZ CS-W3-WD1200G EUP))
|
|
$(eval $(call generate-ipq-wifi-package,glinet_gl-s1300,GL.iNet GL-S1300))
|
|
$(eval $(call generate-ipq-wifi-package,linksys_ea8300,Linksys EA8300))
|
|
$(eval $(call generate-ipq-wifi-package,linksys_mr8300-v0,Linksys MR8300))
|
|
$(eval $(call generate-ipq-wifi-package,luma_wrtq-329acn,Luma WRTQ-329ACN))
|
|
$(eval $(call generate-ipq-wifi-package,mobipromo_cm520-79f,MobiPromo CM520-79F))
|
|
$(eval $(call generate-ipq-wifi-package,plasmacloud_pa1200,Plasma Cloud PA1200))
|
|
$(eval $(call generate-ipq-wifi-package,plasmacloud_pa2200,Plasma Cloud PA2200))
|
|
$(eval $(call generate-ipq-wifi-package,qxwlan_e2600ac,Qxwlan E2600AC))
|
|
|
|
$(foreach PACKAGE,$(ALLWIFIPACKAGES),$(eval $(call BuildPackage,$(PACKAGE))))
|