openwrt/target/linux/ath79/dts/ar9341_engenius_ens202ext-v1.dts
Bjørn Mork 01a1e21863 kernel: mtdsplit_uimage: replace "openwrt, okli" parser
The only difference between the "openwrt,okli" and the generic
parser is the magic.  Set this in device tree for all affected
devices and  remove the "openwrt,okli" parser.

Tested-by: Michael Pratt <mcpratt@protonmail.com> # EAP300 v2, ENS202EXT and ENH202
Signed-off-by: Bjørn Mork <bjorn@mork.no>
2021-01-22 21:03:11 +01:00

182 lines
2.9 KiB
Plaintext

// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
#include "ar9341.dtsi"
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/input/input.h>
#include <dt-bindings/mtd/partitions/uimage.h>
/ {
model = "Engenius ENS202EXT v1";
compatible = "engenius,ens202ext-v1", "qca,ar9341";
aliases {
serial0 = &uart;
led-boot = &led_power;
led-failsafe = &led_power;
led-running = &led_power;
led-upgrade = &led_power;
};
keys {
compatible = "gpio-keys";
reset {
label = "Reset";
linux,code = <KEY_RESTART>;
gpios = <&gpio 1 GPIO_ACTIVE_LOW>;
debounce-interval = <60>;
};
};
leds {
compatible = "gpio-leds";
led_power: power {
label = "amber:power";
gpios = <&gpio 14 GPIO_ACTIVE_LOW>;
default-state = "on";
};
wlan {
label = "amber:wlan";
gpios = <&gpio 18 GPIO_ACTIVE_LOW>;
linux,default-trigger = "phy0tpt";
};
rssilow {
label = "red:rssilow";
gpios = <&gpio 16 GPIO_ACTIVE_LOW>;
};
rssimedium {
label = "amber:rssimedium";
gpios = <&gpio 17 GPIO_ACTIVE_LOW>;
};
rssihigh {
label = "green:rssihigh";
gpios = <&gpio 0 GPIO_ACTIVE_LOW>;
};
};
virtual_flash {
compatible = "mtd-concat";
devices = <&fwconcat0 &fwconcat1>;
partitions {
compatible = "fixed-partitions";
#address-cells = <1>;
#size-cells = <1>;
partition@0 {
compatible = "openwrt,uimage", "denx,uimage";
openwrt,ih-magic = <IH_MAGIC_OKLI>;
label = "firmware";
reg = <0x0 0x0>;
};
};
};
};
&ref {
clock-frequency = <40000000>;
};
&uart {
status = "okay";
};
&spi {
status = "okay";
flash@0 {
compatible = "jedec,spi-nor";
reg = <0>;
spi-max-frequency = <40000000>;
partitions {
compatible = "fixed-partitions";
#address-cells = <1>;
#size-cells = <1>;
partition@0 {
label = "u-boot";
reg = <0x000000 0x040000>;
read-only;
};
partition@40000 {
label = "u-boot-env";
reg = <0x040000 0x010000>;
};
partition@50000 {
label = "custom";
reg = <0x050000 0x050000>;
read-only;
};
partition@a0000 {
label = "loader";
reg = <0x0a0000 0x010000>;
read-only;
};
fwconcat1: partition@b0000 {
label = "fwconcat1";
reg = <0x0b0000 0x170000>;
};
partition@220000 {
label = "fakeroot";
reg = <0x220000 0x010000>;
read-only;
};
fwconcat0: partition@230000 {
label = "fwconcat0";
reg = <0x230000 0xbc0000>;
};
partition@df0000 {
label = "failsafe";
reg = <0xdf0000 0x200000>;
read-only;
};
art: partition@ff0000 {
label = "art";
reg = <0xff0000 0x010000>;
read-only;
};
};
};
};
&eth0 {
status = "okay";
phy-handle = <&swphy0>;
mtd-mac-address = <&art 0x0>;
};
&eth1 {
status = "okay";
mtd-mac-address = <&art 0x0>;
gmac-config {
device = <&gmac>;
switch-phy-swap = <1>;
};
};
&wmac {
status = "okay";
mtd-cal-data = <&art 0x1000>;
};