ExternalVendorCode/openwrt
1
0
Fork 0
mirror of https://github.com/openwrt/openwrt.git synced 2024-12-22 23:12:32 +00:00
Code Issues Actions 6 Packages Projects Releases Wiki Activity
45eb57f12f
openwrt/target/linux/ipq40xx/image/generic.mk
Christian Lamparter 45eb57f12f ipq40xx: unbreak EZVIZ CS-W3-WD1200G EUP on 5.10 
with current images, the device is no longer booting.
It gets stuck in the bootloader with "Config not available"
and drops to the uboot shell.

|flash_type: 0
|Hit any key to stop autoboot:  0
|SF: Detected MX25L12805D with page size 4 KiB, total 16 MiB
|Config not availabale
|(IPQ40xx) #

This is because the default bootcmd "bootipq" will only read
the first four MiB of the kernel image. With 5.10 the gzip'd
kernel is slightly larger. So the part of the FIT image which
had the configuration is cut off. Hence it can't find it.

To update the bootcmd, you have to attach the serial console
again and enter the following commands into the boot prompt:

 # setenv bootcmd "sf probe; sf read 84000000 180000 600000; bootm"
 # saveenv
 # run bootcmd

This will allow booting kernels with up to six MiB. This also
allows us to drop the DEVICE_DTS_CONFIG hack we had to use.

Note:
uboot doesn't support LZMA. It fails with:
"Unimplemented compression type 3"

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2021-12-04 00:36:47 +01:00

981 lines
29 KiB
Makefile
Raw Blame History

DEVICE_VARS += NETGEAR_BOARD_ID NETGEAR_HW_ID
DEVICE_VARS += RAS_BOARD RAS_ROOTFS_SIZE RAS_VERSION
DEVICE_VARS += WRGG_DEVNAME WRGG_SIGNATURE
define Device/FitImage
KERNEL_SUFFIX := -fit-uImage.itb
KERNEL = kernel-bin | gzip | fit gzip $$(DTS_DIR)/$$(DEVICE_DTS).dtb
KERNEL_NAME := Image
endef
define Device/FitImageLzma
KERNEL_SUFFIX := -fit-uImage.itb
KERNEL = kernel-bin | lzma | fit lzma $$(DTS_DIR)/$$(DEVICE_DTS).dtb
KERNEL_NAME := Image
endef
define Device/FitzImage
KERNEL_SUFFIX := -fit-zImage.itb
KERNEL = kernel-bin | fit none $$(DTS_DIR)/$$(DEVICE_DTS).dtb
KERNEL_NAME := zImage
endef
define Device/UbiFit
KERNEL_IN_UBI := 1
IMAGES := nand-factory.ubi nand-sysupgrade.bin
IMAGE/nand-factory.ubi := append-ubi
IMAGE/nand-sysupgrade.bin := sysupgrade-tar | append-metadata
endef
define Device/DniImage
$(call Device/FitzImage)
NETGEAR_BOARD_ID :=
NETGEAR_HW_ID :=
IMAGES += factory.img
IMAGE/factory.img := append-kernel | pad-offset 64k 64 | append-uImage-fakehdr filesystem | append-rootfs | pad-rootfs | netgear-dni
IMAGE/sysupgrade.bin := append-kernel | pad-offset 64k 64 | append-uImage-fakehdr filesystem | \
append-rootfs | pad-rootfs | check-size | append-metadata
endef
define Build/append-rootfshdr
mkimage -A $(LINUX_KARCH) \
-O linux -T filesystem \
-C lzma -a $(KERNEL_LOADADDR) -e $(if $(KERNEL_ENTRY),$(KERNEL_ENTRY),$(KERNEL_LOADADDR)) \
-n root.squashfs -d $(IMAGE_ROOTFS) $@.new
dd if=$@.new bs=64 count=1 >> $(IMAGE_KERNEL)
endef
define Build/append-rutx-metadata
echo \
'{ \
"device_code": [".*"], \
"hwver": [".*"], \
"batch": [".*"], \
"serial": [".*"], \
"supported_devices":["teltonika,rutx"] \
}' | fwtool -I - $@
endef
define Build/mkmylofw_32m
$(eval device_id=$(word 1,$(1)))
$(eval revision=$(word 2,$(1)))
let \
size="$$(stat -c%s $@)" \
pad="$(subst k,* 1024,$(BLOCKSIZE))" \
pad="(pad - (size % pad)) % pad" \
newsize='size + pad'; \
$(STAGING_DIR_HOST)/bin/mkmylofw \
-B WPE72 -i 0x11f6:$(device_id):0x11f6:$(device_id) -r $(revision) \
-s 0x2000000 -p0x180000:$$newsize:al:0x80208000:"OpenWrt":$@ \
$@.new
@mv $@.new $@
endef
define Build/wac5xx-netgear-tar
mkdir $@.tmp
mv $@ $@.tmp/wac5xx-ubifs-root.img
md5sum $@.tmp/wac5xx-ubifs-root.img > $@.tmp/wac5xx-ubifs-root.md5sum
echo "WAC505 WAC510" > $@.tmp/metadata.txt
echo "WAC505_V9.9.9.9" > $@.tmp/version
tar -C $@.tmp/ -cf $@ .
rm -rf $@.tmp
endef
define Build/qsdk-ipq-factory-nand-askey
$(TOPDIR)/scripts/mkits-qsdk-ipq-image.sh $@.its\
askey_kernel $(IMAGE_KERNEL) \
askey_fs $(IMAGE_ROOTFS) \
ubifs $@
PATH=$(LINUX_DIR)/scripts/dtc:$(PATH) mkimage -f $@.its $@.new
@mv $@.new $@
endef
define Build/qsdk-ipq-app-gpt
cp $@ $@.tmp 2>/dev/null || true
ptgen -g -o $@.tmp -a 1 -l 1024 \
-t 0x2e -N 0:HLOS -r -p 32M \
-t 0x83 -N rootfs -r -p 128M \
-N rootfs_data -p 512M
cat $@.tmp >> $@
rm $@.tmp
endef
define Build/SenaoFW
-$(STAGING_DIR_HOST)/bin/mksenaofw \
-n $(BOARD_NAME) -r $(VENDOR_ID) -p $(1) \
-c $(DATECODE) -w $(2) -x $(CW_VER) -t 0 \
-e $@ \
-o $@.new
@cp $@.new $@
endef
define Build/wrgg-image
mkwrggimg -i $@ \
-o $@.new \
-d "$(WRGG_DEVNAME)" \
-s "$(WRGG_SIGNATURE)" \
-v "" -m "" -B ""
mv $@.new $@
endef
define Device/8dev_habanero-dvk
$(call Device/FitImageLzma)
DEVICE_VENDOR := 8devices
DEVICE_MODEL := Habanero DVK
IMAGE_SIZE := 30976k
SOC := qcom-ipq4019
DEVICE_PACKAGES := ipq-wifi-8dev_habanero-dvk
IMAGE/sysupgrade.bin := append-kernel | pad-to 64k | append-rootfs | pad-rootfs | check-size | append-metadata
endef
TARGET_DEVICES += 8dev_habanero-dvk
define Device/8dev_jalapeno-common
$(call Device/FitImage)
$(call Device/UbiFit)
BLOCKSIZE := 128k
PAGESIZE := 2048
SOC := qcom-ipq4018
endef
define Device/8dev_jalapeno
$(call Device/8dev_jalapeno-common)
DEVICE_VENDOR := 8devices
DEVICE_MODEL := Jalapeno
endef
TARGET_DEVICES += 8dev_jalapeno
define Device/alfa-network_ap120c-ac
$(call Device/FitImage)
$(call Device/UbiFit)
DEVICE_VENDOR := ALFA Network
DEVICE_MODEL := AP120C-AC
SOC := qcom-ipq4018
DEVICE_PACKAGES := kmod-usb-acm kmod-tpm-i2c-atmel
BLOCKSIZE := 128k
PAGESIZE := 2048
IMAGE_SIZE := 65536k
IMAGES := nand-factory.bin nand-sysupgrade.bin
IMAGE/nand-factory.bin := append-ubi | qsdk-ipq-factory-nand
endef
TARGET_DEVICES += alfa-network_ap120c-ac
define Device/aruba_glenmorangie
$(call Device/FitImageLzma)
DEVICE_VENDOR := Aruba
SOC := qcom-ipq4029
DEVICE_PACKAGES := ipq-wifi-aruba_ap-303
endef
define Device/aruba_ap-303
$(call Device/aruba_glenmorangie)
DEVICE_MODEL := AP-303
endef
TARGET_DEVICES += aruba_ap-303
define Device/aruba_ap-303h
$(call Device/aruba_glenmorangie)
DEVICE_MODEL := AP-303H
endef
TARGET_DEVICES += aruba_ap-303h
define Device/aruba_ap-365
$(call Device/aruba_glenmorangie)
DEVICE_MODEL := AP-365
DEVICE_PACKAGES += kmod-hwmon-ad7418
endef
TARGET_DEVICES += aruba_ap-365
define Device/asus_map-ac2200
$(call Device/FitImageLzma)
DEVICE_VENDOR := ASUS
DEVICE_MODEL := Lyra (MAP-AC2200)
SOC := qcom-ipq4019
DEVICE_PACKAGES := ath10k-firmware-qca9888-ct kmod-ath3k
endef
TARGET_DEVICES += asus_map-ac2200
define Device/asus_rt-ac58u
$(call Device/FitImageLzma)
DEVICE_VENDOR := ASUS
DEVICE_MODEL := RT-AC58U
SOC := qcom-ipq4018
BLOCKSIZE := 128k
PAGESIZE := 2048
DTB_SIZE := 65536
IMAGE_SIZE := 20439364
FILESYSTEMS := squashfs
# Someone - in their infinite wisdom - decided to put the firmware
# version in front of the image name \03\00\00\04 => Version 3.0.0.4
# Since u-boot works with strings we either need another fixup step
# to add a version... or we are very careful not to add '\0' into that
# string and call it a day.... Yeah, we do the latter!
UIMAGE_NAME:=$(shell echo -e '\03\01\01\01RT-AC58U')
DEVICE_PACKAGES := -kmod-ath10k-ct kmod-ath10k-ct-smallbuffers \
kmod-usb-ledtrig-usbport
endef
TARGET_DEVICES += asus_rt-ac58u
define Device/avm_fritzbox-4040
$(call Device/FitImageLzma)
DEVICE_VENDOR := AVM
DEVICE_MODEL := FRITZ!Box 4040
SOC := qcom-ipq4018
BOARD_NAME := fritz4040
IMAGE_SIZE := 29056k
UBOOT_PATH := $(STAGING_DIR_IMAGE)/uboot-fritz4040.bin
UBOOT_PARTITION_SIZE := 524288
IMAGES += eva.bin
IMAGE/eva.bin := append-uboot | pad-to $$$$(UBOOT_PARTITION_SIZE) | append-kernel | append-rootfs | pad-rootfs
IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | check-size | append-metadata
DEVICE_PACKAGES := fritz-tffs fritz-caldata
endef
TARGET_DEVICES += avm_fritzbox-4040
define Device/avm_fritzbox-7530
$(call Device/FitImageLzma)
DEVICE_VENDOR := AVM
DEVICE_MODEL := FRITZ!Box 7530
SOC := qcom-ipq4019
DEVICE_PACKAGES := fritz-caldata fritz-tffs-nand
endef
TARGET_DEVICES += avm_fritzbox-7530
define Device/avm_fritzrepeater-1200
$(call Device/FitImageLzma)
DEVICE_VENDOR := AVM
DEVICE_MODEL := FRITZ!Repeater 1200
SOC := qcom-ipq4019
DEVICE_PACKAGES := fritz-caldata fritz-tffs-nand ipq-wifi-avm_fritzrepeater-1200
endef
TARGET_DEVICES += avm_fritzrepeater-1200
define Device/avm_fritzrepeater-3000
$(call Device/FitImageLzma)
DEVICE_VENDOR := AVM
DEVICE_MODEL := FRITZ!Repeater 3000
SOC := qcom-ipq4019
DEVICE_PACKAGES := ath10k-firmware-qca9984-ct fritz-caldata fritz-tffs-nand
endef
TARGET_DEVICES += avm_fritzrepeater-3000
define Device/buffalo_wtr-m2133hp
$(call Device/FitImage)
$(call Device/UbiFit)
DEVICE_VENDOR := Buffalo
DEVICE_MODEL := WTR-M2133HP
SOC := qcom-ipq4019
DEVICE_PACKAGES := ath10k-firmware-qca9984-ct ipq-wifi-buffalo_wtr-m2133hp
BLOCKSIZE := 128k
PAGESIZE := 2048
endef
TARGET_DEVICES += buffalo_wtr-m2133hp
define Device/cellc_rtl30vw
KERNEL_SUFFIX := -fit-zImage.itb
KERNEL_INITRAMFS = kernel-bin | gzip | fit gzip $$(DTS_DIR)/$$(DEVICE_DTS).dtb
KERNEL = kernel-bin | fit none $$(DTS_DIR)/$$(DEVICE_DTS).dtb | uImage lzma | pad-to 2048
KERNEL_NAME := zImage
KERNEL_IN_UBI :=
IMAGES := nand-factory.bin nand-sysupgrade.bin
IMAGE/nand-factory.bin := append-rootfshdr | append-ubi | qsdk-ipq-factory-nand-askey
IMAGE/nand-sysupgrade.bin := append-rootfshdr | sysupgrade-tar | append-metadata
DEVICE_VENDOR := Cell C
DEVICE_MODEL := RTL30VW
SOC := qcom-ipq4019
DEVICE_DTS_CONFIG := config@5
KERNEL_INSTALL := 1
KERNEL_SIZE := 4096k
IMAGE_SIZE := 57344k
BLOCKSIZE := 128k
PAGESIZE := 2048
DEVICE_PACKAGES := kmod-usb-net-qmi-wwan kmod-usb-serial-option uqmi ipq-wifi-cellc_rtl30vw
endef
TARGET_DEVICES += cellc_rtl30vw
define Device/cilab_meshpoint-one
$(call Device/8dev_jalapeno-common)
DEVICE_VENDOR := Crisis Innovation Lab
DEVICE_MODEL := MeshPoint.One
DEVICE_PACKAGES := kmod-i2c-gpio kmod-iio-bmp280-i2c kmod-hwmon-ina2xx kmod-rtc-pcf2127
endef
TARGET_DEVICES += cilab_meshpoint-one
define Device/compex_wpj419
$(call Device/FitImage)
$(call Device/UbiFit)
DEVICE_VENDOR := Compex
DEVICE_MODEL := WPJ419
SOC := qcom-ipq4019
DEVICE_DTS_CONFIG := config@12
KERNEL_INSTALL := 1
BLOCKSIZE := 128k
PAGESIZE := 2048
FILESYSTEMS := squashfs
endef
TARGET_DEVICES += compex_wpj419
define Device/compex_wpj428
$(call Device/FitImage)
DEVICE_VENDOR := Compex
DEVICE_MODEL := WPJ428
SOC := qcom-ipq4028
DEVICE_DTS_CONFIG := config@4
BLOCKSIZE := 64k
IMAGE_SIZE := 31232k
KERNEL_SIZE := 4096k
IMAGES += cpximg-6a04.bin
IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | append-metadata
IMAGE/cpximg-6a04.bin := append-kernel | append-rootfs | pad-rootfs | mkmylofw_32m 0x8A2 3
DEVICE_PACKAGES := kmod-gpio-beeper
DEFAULT := n
endef
TARGET_DEVICES += compex_wpj428
define Device/devolo_magic-2-wifi-next
$(call Device/FitImage)
DEVICE_VENDOR := devolo
DEVICE_MODEL := Magic 2 WiFi next
SOC := qcom-ipq4018
KERNEL_SIZE := 4096k
# If the bootloader sees 0xDEADC0DE and this trailer at the 64k boundary of a TFTP image
# it will bootm it, just like we want for the initramfs.
KERNEL_INITRAMFS := kernel-bin | gzip | fit gzip $$(DTS_DIR)/$$(DEVICE_DTS).dtb | pad-to 64k |\
append-string -e '\xDE\xAD\xC0\xDE{"fl_initramfs":""}\x00'
IMAGE_SIZE := 26624k
IMAGES := sysupgrade.bin
IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | append-metadata
DEVICE_PACKAGES := ipq-wifi-devolo_magic-2-wifi-next
DEFAULT := n
endef
TARGET_DEVICES += devolo_magic-2-wifi-next
define Device/dlink_dap-2610
$(call Device/FitImageLzma)
DEVICE_VENDOR := D-Link
DEVICE_MODEL := DAP-2610
SOC := qcom-ipq4018
DEVICE_DTS_CONFIG := config@ap.dk01.1-c1
BLOCKSIZE := 64k
WRGG_DEVNAME := /dev/mtdblock/8
WRGG_SIGNATURE := wapac30_dkbs_dap2610
IMAGE_SIZE := 14080k
IMAGES += factory.bin
# Bootloader expects a special 160 byte header which is added by
# wrgg-image.
# Factory image size must be larger than 6MB, and size in wrgg header must
# match actual factory image size to be flashable from D-Link http server.
# Bootloader verifies checksum of wrgg image before booting, thus jffs2
# cannot be part of the wrgg image. This is solved in the factory image by
# having the rootfs at the end of the image (without pad-rootfs). And in
# the sysupgrade image only the kernel is included in the wrgg checksum,
# but this is not flashable from the D-link http server.
# append-rootfs must start on an erase block boundary.
IMAGE/factory.bin := append-kernel | pad-offset 6144k 160 | append-rootfs | wrgg-image | check-size
IMAGE/sysupgrade.bin := append-kernel | wrgg-image | pad-to $$$$(BLOCKSIZE) | append-rootfs | pad-rootfs | check-size | append-metadata
DEVICE_PACKAGES := ipq-wifi-dlink_dap2610
endef
TARGET_DEVICES += dlink_dap-2610
define Device/edgecore_ecw5211
$(call Device/FitImage)
$(call Device/UbiFit)
DEVICE_VENDOR := Edgecore
DEVICE_MODEL := ECW5211
SOC := qcom-ipq4018
BLOCKSIZE := 128k
PAGESIZE := 2048
DEVICE_DTS_CONFIG := config@ap.dk01.1-c2
DEVICE_PACKAGES := kmod-tpm-i2c-atmel kmod-usb-acm
endef
TARGET_DEVICES += edgecore_ecw5211
define Device/edgecore_oap100
$(call Device/FitImage)
$(call Device/UbiFit)
DEVICE_VENDOR := Edgecore
DEVICE_MODEL := OAP100
SOC := qcom-ipq4019
BLOCKSIZE := 128k
PAGESIZE := 2048
IMAGES := nand-sysupgrade.bin
DEVICE_DTS_CONFIG := config@ap.dk07.1-c1
DEVICE_PACKAGES := ipq-wifi-edgecore_oap100 kmod-usb-acm kmod-usb-net kmod-usb-net-cdc-qmi uqmi
endef
TARGET_DEVICES += edgecore_oap100
define Device/engenius_eap1300
$(call Device/FitImage)
DEVICE_VENDOR := EnGenius
DEVICE_MODEL := EAP1300
DEVICE_DTS_CONFIG := config@4
BOARD_NAME := eap1300
SOC := qcom-ipq4018
KERNEL_SIZE := 5120k
IMAGE_SIZE := 25344k
IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | append-metadata
endef
TARGET_DEVICES += engenius_eap1300
define Device/engenius_eap2200
$(call Device/FitImage)
$(call Device/UbiFit)
DEVICE_VENDOR := EnGenius
DEVICE_MODEL := EAP2200
SOC := qcom-ipq4019
BLOCKSIZE := 128k
PAGESIZE := 2048
DEVICE_PACKAGES := ath10k-firmware-qca9888-ct ipq-wifi-engenius_eap2200 -kmod-ath10k-ct kmod-ath10k-ct-smallbuffers
endef
TARGET_DEVICES += engenius_eap2200
define Device/engenius_emd1
$(call Device/FitImage)
DEVICE_VENDOR := EnGenius
DEVICE_MODEL := EMD1
DEVICE_DTS_CONFIG := config@4
SOC := qcom-ipq4018
IMAGE_SIZE := 30720k
IMAGES += factory.bin
IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | append-metadata
IMAGE/factory.bin := qsdk-ipq-factory-nor | check-size
DEVICE_PACKAGES := ipq-wifi-engenius_emd1
endef
TARGET_DEVICES += engenius_emd1
define Device/engenius_emr3500
$(call Device/FitImage)
DEVICE_VENDOR := EnGenius
DEVICE_MODEL := EMR3500
DEVICE_DTS_CONFIG := config@4
SOC := qcom-ipq4018
KERNEL_SIZE := 4096k
IMAGE_SIZE := 30720k
IMAGES += factory.bin
IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | append-metadata
IMAGE/factory.bin := qsdk-ipq-factory-nor | check-size
DEVICE_PACKAGES := ipq-wifi-engenius_emr3500
DEFAULT := n
endef
TARGET_DEVICES += engenius_emr3500
define Device/engenius_ens620ext
$(call Device/FitImage)
DEVICE_VENDOR := EnGenius
DEVICE_MODEL := ENS620EXT
SOC := qcom-ipq4018
DEVICE_DTS_CONFIG := config@4
BLOCKSIZE := 64k
PAGESIZE := 256
BOARD_NAME := ENS620EXT
VENDOR_ID := 0x0101
PRODUCT_ID := 0x79
PRODUCT_ID_NEW := 0xA4
DATECODE := 190507
FW_VER := 3.1.2
FW_VER_NEW := 3.5.6
CW_VER := 1.8.99
IMAGE_SIZE := 21312k
KERNEL_SIZE := 5120k
FILESYSTEMS := squashfs
IMAGES += factory_30.bin factory_35.bin
IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | check-size | append-metadata
IMAGE/factory_30.bin := append-kernel | pad-to $$$$(KERNEL_SIZE) | append-rootfs | pad-rootfs | check-size | SenaoFW $$$$(PRODUCT_ID) $$$$(FW_VER)
IMAGE/factory_35.bin := qsdk-ipq-factory-nor | check-size | SenaoFW $$$$(PRODUCT_ID_NEW) $$$$(FW_VER_NEW)
endef
TARGET_DEVICES += engenius_ens620ext
define Device/ezviz_cs-w3-wd1200g-eup
$(call Device/FitImage)
DEVICE_VENDOR := EZVIZ
DEVICE_MODEL := CS-W3-WD1200G
DEVICE_VARIANT := EUP
IMAGE_SIZE := 14848k
KERNEL_SIZE = 6m
SOC := qcom-ipq4018
IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | \
append-metadata
DEVICE_PACKAGES := -kmod-ath10k-ct kmod-ath10k-ct-smallbuffers \
ipq-wifi-ezviz_cs-w3-wd1200g-eup
DEVICE_COMPAT_VERSION := 2.0
DEVICE_COMPAT_MESSAGE := uboot's bootcmd has to be updated (see wiki). \
Upgrade via sysupgrade mechanism is not possible.
endef
TARGET_DEVICES += ezviz_cs-w3-wd1200g-eup
define Device/glinet_gl-ap1300
$(call Device/FitImage)
$(call Device/UbiFit)
DEVICE_VENDOR := GL.iNet
DEVICE_MODEL := GL-AP1300
SOC := qcom-ipq4018
DEVICE_DTS_CONFIG := config@ap.dk01.1-c2
BLOCKSIZE := 128k
PAGESIZE := 2048
IMAGE_SIZE := 131072k
KERNEL_INSTALL := 1
DEVICE_PACKAGES := ipq-wifi-glinet_gl-ap1300
endef
TARGET_DEVICES += glinet_gl-ap1300
define Device/glinet_gl-b1300
$(call Device/FitzImage)
DEVICE_VENDOR := GL.iNet
DEVICE_MODEL := GL-B1300
BOARD_NAME := gl-b1300
SOC := qcom-ipq4029
KERNEL_SIZE := 4096k
IMAGE_SIZE := 26624k
IMAGE/sysupgrade.bin := append-kernel |append-rootfs | pad-rootfs | append-metadata
endef
TARGET_DEVICES += glinet_gl-b1300
define Device/glinet_gl-b2200
$(call Device/FitzImage)
DEVICE_VENDOR := GL.iNet
DEVICE_MODEL := GL-B2200
SOC := qcom-ipq4019
DEVICE_DTS_CONFIG := config@ap.dk04.1-c3
KERNEL_INITRAMFS_SUFFIX := -recovery.itb
IMAGES := emmc.img.gz sysupgrade.bin
IMAGE/emmc.img.gz := qsdk-ipq-app-gpt |\
pad-to 1024k | append-kernel |\
pad-to 33792k | append-rootfs |\
append-metadata | gzip
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
DEVICE_PACKAGES := ath10k-firmware-qca9888-ct ipq-wifi-glinet_gl-b2200 \
kmod-fs-ext4 kmod-mmc kmod-spi-dev mkf2fs e2fsprogs kmod-fs-f2fs
endef
TARGET_DEVICES += glinet_gl-b2200
define Device/glinet_gl-s1300
$(call Device/FitzImage)
DEVICE_VENDOR := GL.iNet
DEVICE_MODEL := GL-S1300
SOC := qcom-ipq4029
KERNEL_SIZE := 4096k
IMAGE_SIZE := 26624k
IMAGES := sysupgrade.bin
IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | append-metadata
DEVICE_PACKAGES := ipq-wifi-glinet_gl-s1300 kmod-fs-ext4 kmod-mmc kmod-spi-dev
endef
TARGET_DEVICES += glinet_gl-s1300
define Device/linksys_ea6350v3
# The Linksys EA6350v3 has a uboot bootloader that does not
# support either booting lzma kernel images nor booting UBI
# partitions. This uboot, however, supports raw kernel images and
# gzipped images.
#
# As for the time of writing this, the device will boot the kernel
# from a fixed address with a fixed length of 3MiB. Also, the
# device has a hard-coded kernel command line that requieres the
# rootfs and alt_rootfs to be in mtd11 and mtd13 respectively.
# Oh... and the kernel partition overlaps with the rootfs
# partition (the same for alt_kernel and alt_rootfs).
#
# If you are planing re-partitioning the device, you may want to
# keep those details in mind:
# 1. The kernel adresses you should honor are 0x00000000 and
# 0x02800000 respectively.
# 2. The kernel size (plus the dtb) cannot exceed 3.00MiB in size.
# 3. You can use 'zImage', but not a raw 'Image' packed with lzma.
# 4. The kernel command line from uboot is harcoded to boot with
# rootfs either in mtd11 or mtd13.
$(call Device/FitzImage)
DEVICE_VENDOR := Linksys
DEVICE_MODEL := EA6350
DEVICE_VARIANT := v3
SOC := qcom-ipq4018
BLOCKSIZE := 128k
PAGESIZE := 2048
KERNEL_SIZE := 3072k
IMAGE_SIZE := 37888k
UBINIZE_OPTS := -E 5
IMAGES += factory.bin
IMAGE/factory.bin := append-kernel | append-uImage-fakehdr filesystem | pad-to $$$$(KERNEL_SIZE) | append-ubi | linksys-image type=EA6350v3
endef
TARGET_DEVICES += linksys_ea6350v3
define Device/linksys_ea8300
$(call Device/FitzImage)
DEVICE_VENDOR := Linksys
DEVICE_MODEL := EA8300
SOC := qcom-ipq4019
KERNEL_SIZE := 3072k
IMAGE_SIZE := 87040k
BLOCKSIZE := 128k
PAGESIZE := 2048
UBINIZE_OPTS := -E 5 # EOD marks to "hide" factory sig at EOF
IMAGES += factory.bin
IMAGE/factory.bin := append-kernel | pad-to $$$$(KERNEL_SIZE) | append-ubi | linksys-image type=EA8300
DEVICE_PACKAGES := ath10k-firmware-qca9888-ct ipq-wifi-linksys_ea8300 kmod-usb-ledtrig-usbport
endef
TARGET_DEVICES += linksys_ea8300
define Device/linksys_mr8300
$(call Device/FitzImage)
DEVICE_VENDOR := Linksys
DEVICE_MODEL := MR8300
SOC := qcom-ipq4019
KERNEL_SIZE := 3072k
IMAGE_SIZE := 87040k
BLOCKSIZE := 128k
PAGESIZE := 2048
UBINIZE_OPTS := -E 5 # EOD marks to "hide" factory sig at EOF
IMAGES += factory.bin
IMAGE/factory.bin := append-kernel | pad-to $$$$(KERNEL_SIZE) | append-ubi | linksys-image type=MR8300
DEVICE_PACKAGES := ath10k-firmware-qca9888-ct ipq-wifi-linksys_mr8300-v0 kmod-usb-ledtrig-usbport
endef
TARGET_DEVICES += linksys_mr8300
define Device/luma_wrtq-329acn
$(call Device/FitImage)
DEVICE_VENDOR := Luma Home
DEVICE_MODEL := WRTQ-329ACN
SOC := qcom-ipq4018
DEVICE_PACKAGES := ipq-wifi-luma_wrtq-329acn kmod-ath3k kmod-eeprom-at24 kmod-i2c-gpio
IMAGE_SIZE := 76632k
BLOCKSIZE := 128k
PAGESIZE := 2048
endef
TARGET_DEVICES += luma_wrtq-329acn
define Device/meraki_mr33
$(call Device/FitImage)
DEVICE_VENDOR := Cisco Meraki
DEVICE_MODEL := MR33
SOC := qcom-ipq4029
BLOCKSIZE := 128k
PAGESIZE := 2048
DEVICE_PACKAGES := -swconfig ath10k-firmware-qca9887-ct
endef
TARGET_DEVICES += meraki_mr33
define Device/mobipromo_cm520-79f
$(call Device/FitzImage)
$(call Device/UbiFit)
DEVICE_VENDOR := MobiPromo
DEVICE_MODEL := CM520-79F
SOC := qcom-ipq4019
BLOCKSIZE := 128k
PAGESIZE := 2048
DEVICE_PACKAGES := ipq-wifi-mobipromo_cm520-79f kmod-usb-ledtrig-usbport
endef
TARGET_DEVICES += mobipromo_cm520-79f
define Device/netgear_ex61x0v2
$(call Device/DniImage)
DEVICE_VENDOR := NETGEAR
DEVICE_DTS_CONFIG := config@4
NETGEAR_BOARD_ID := EX6150v2series
NETGEAR_HW_ID := 29765285+16+0+128+2x2
IMAGE_SIZE := 14400k
SOC := qcom-ipq4018
endef
define Device/netgear_ex6100v2
$(call Device/netgear_ex61x0v2)
DEVICE_MODEL := EX6100
DEVICE_VARIANT := v2
endef
TARGET_DEVICES += netgear_ex6100v2
define Device/netgear_ex6150v2
$(call Device/netgear_ex61x0v2)
DEVICE_MODEL := EX6150
DEVICE_VARIANT := v2
endef
TARGET_DEVICES += netgear_ex6150v2
define Device/netgear_orbi
$(call Device/DniImage)
SOC := qcom-ipq4019
DEVICE_VENDOR := NETGEAR
IMAGE/factory.img := append-kernel | pad-offset 128k 64 | \
append-uImage-fakehdr filesystem | pad-to $$$$(KERNEL_SIZE) | \
append-rootfs | pad-rootfs | netgear-dni
IMAGE/sysupgrade.bin/squashfs := append-rootfs | pad-to 64k | \
sysupgrade-tar rootfs=$$$$@ | append-metadata
DEVICE_PACKAGES := ath10k-firmware-qca9984-ct e2fsprogs kmod-fs-ext4 losetup
endef
define Device/netgear_rbx50
$(call Device/netgear_orbi)
NETGEAR_HW_ID := 29765352+0+4000+512+2x2+2x2+4x4
KERNEL_SIZE := 3932160
ROOTFS_SIZE := 32243712
IMAGE_SIZE := 36175872
endef
define Device/netgear_rbr50
$(call Device/netgear_rbx50)
DEVICE_MODEL := RBR50
DEVICE_VARIANT := v1
NETGEAR_BOARD_ID := RBR50
endef
TARGET_DEVICES += netgear_rbr50
define Device/netgear_rbs50
$(call Device/netgear_rbx50)
DEVICE_MODEL := RBS50
DEVICE_VARIANT := v1
NETGEAR_BOARD_ID := RBS50
endef
TARGET_DEVICES += netgear_rbs50
define Device/netgear_srx60
$(call Device/netgear_orbi)
NETGEAR_HW_ID := 29765352+0+4096+512+2x2+2x2+4x4
KERNEL_SIZE := 3932160
ROOTFS_SIZE := 32243712
IMAGE_SIZE := 36175872
endef
define Device/netgear_srr60
$(call Device/netgear_srx60)
DEVICE_MODEL := SRR60
NETGEAR_BOARD_ID := SRR60
endef
TARGET_DEVICES += netgear_srr60
define Device/netgear_srs60
$(call Device/netgear_srx60)
DEVICE_MODEL := SRS60
NETGEAR_BOARD_ID := SRS60
endef
TARGET_DEVICES += netgear_srs60
define Device/netgear_wac510
$(call Device/FitImage)
$(call Device/UbiFit)
DEVICE_VENDOR := Netgear
DEVICE_MODEL := WAC510
SOC := qcom-ipq4018
DEVICE_DTS_CONFIG := config@5
BLOCKSIZE := 128k
PAGESIZE := 2048
IMAGES += nand-factory.tar
IMAGE/nand-factory.tar := append-ubi | wac5xx-netgear-tar
DEVICE_PACKAGES := uboot-envtools
endef
TARGET_DEVICES += netgear_wac510
define Device/openmesh_a42
$(call Device/FitImageLzma)
DEVICE_VENDOR := OpenMesh
DEVICE_MODEL := A42
SOC := qcom-ipq4018
DEVICE_DTS_CONFIG := config@om.a42
BLOCKSIZE := 64k
KERNEL = kernel-bin | lzma | fit lzma $$(DTS_DIR)/$$(DEVICE_DTS).dtb | pad-to $$(BLOCKSIZE)
IMAGE_SIZE := 15616k
IMAGES += factory.bin
IMAGE/factory.bin := append-rootfs | pad-rootfs | openmesh-image ce_type=A42
IMAGE/sysupgrade.bin/squashfs := append-rootfs | pad-rootfs | sysupgrade-tar rootfs=$$$$@ | append-metadata
endef
TARGET_DEVICES += openmesh_a42
define Device/openmesh_a62
$(call Device/FitImageLzma)
DEVICE_VENDOR := OpenMesh
DEVICE_MODEL := A62
SOC := qcom-ipq4019
DEVICE_DTS_CONFIG := config@om.a62
BLOCKSIZE := 64k
KERNEL = kernel-bin | lzma | fit lzma $$(DTS_DIR)/$$(DEVICE_DTS).dtb | pad-to $$(BLOCKSIZE)
IMAGE_SIZE := 15552k
IMAGES += factory.bin
IMAGE/factory.bin := append-rootfs | pad-rootfs | openmesh-image ce_type=A62
IMAGE/sysupgrade.bin/squashfs := append-rootfs | pad-rootfs | sysupgrade-tar rootfs=$$$$@ | append-metadata
DEVICE_PACKAGES := ath10k-firmware-qca9888-ct
endef
TARGET_DEVICES += openmesh_a62
define Device/p2w_r619ac
$(call Device/FitzImage)
$(call Device/UbiFit)
DEVICE_VENDOR := P&W
DEVICE_MODEL := R619AC
SOC := qcom-ipq4019
DEVICE_DTS_CONFIG := config@10
BLOCKSIZE := 128k
PAGESIZE := 2048
DEVICE_PACKAGES := ipq-wifi-p2w_r619ac
endef
define Device/p2w_r619ac-64m
$(call Device/p2w_r619ac)
DEVICE_VARIANT := 64M NAND
IMAGES += nand-factory.bin
IMAGE/nand-factory.bin := append-ubi | qsdk-ipq-factory-nand
endef
TARGET_DEVICES += p2w_r619ac-64m
define Device/p2w_r619ac-128m
$(call Device/p2w_r619ac)
DEVICE_VARIANT := 128M NAND
endef
TARGET_DEVICES += p2w_r619ac-128m
define Device/plasmacloud_pa1200
$(call Device/FitImageLzma)
DEVICE_VENDOR := Plasma Cloud
DEVICE_MODEL := PA1200
SOC := qcom-ipq4018
DEVICE_DTS_CONFIG := config@pc.pa1200
BLOCKSIZE := 64k
KERNEL = kernel-bin | lzma | fit lzma $$(DTS_DIR)/$$(DEVICE_DTS).dtb | pad-to $$(BLOCKSIZE)
IMAGE_SIZE := 15616k
IMAGES += factory.bin
IMAGE/factory.bin := append-rootfs | pad-rootfs | openmesh-image ce_type=PA1200
IMAGE/sysupgrade.bin/squashfs := append-rootfs | pad-rootfs | sysupgrade-tar rootfs=$$$$@ | append-metadata
DEVICE_PACKAGES := ipq-wifi-plasmacloud_pa1200
endef
TARGET_DEVICES += plasmacloud_pa1200
define Device/plasmacloud_pa2200
$(call Device/FitImageLzma)
DEVICE_VENDOR := Plasma Cloud
DEVICE_MODEL := PA2200
SOC := qcom-ipq4019
DEVICE_DTS_CONFIG := config@pc.pa2200
BLOCKSIZE := 64k
KERNEL = kernel-bin | lzma | fit lzma $$(DTS_DIR)/$$(DEVICE_DTS).dtb | pad-to $$(BLOCKSIZE)
IMAGE_SIZE := 15552k
IMAGES += factory.bin
IMAGE/factory.bin := append-rootfs | pad-rootfs | openmesh-image ce_type=PA2200
IMAGE/sysupgrade.bin/squashfs := append-rootfs | pad-rootfs | sysupgrade-tar rootfs=$$$$@ | append-metadata
DEVICE_PACKAGES := ath10k-firmware-qca9888-ct ipq-wifi-plasmacloud_pa2200
endef
TARGET_DEVICES += plasmacloud_pa2200
define Device/qcom_ap-dk01.1-c1
DEVICE_VENDOR := Qualcomm Atheros
DEVICE_MODEL := AP-DK01.1
DEVICE_VARIANT := C1
BOARD_NAME := ap-dk01.1-c1
SOC := qcom-ipq4019
DEVICE_DTS := qcom-ipq4019-ap.dk01.1-c1
KERNEL_INSTALL := 1
KERNEL_SIZE := 4096k
IMAGE_SIZE := 26624k
$(call Device/FitImage)
IMAGE/sysupgrade.bin := append-kernel | pad-to $$$$(KERNEL_SIZE) | append-rootfs | pad-rootfs | append-metadata
DEFAULT := n
endef
TARGET_DEVICES += qcom_ap-dk01.1-c1
define Device/qcom_ap-dk04.1-c1
$(call Device/FitImage)
$(call Device/UbiFit)
DEVICE_VENDOR := Qualcomm Atheros
DEVICE_MODEL := AP-DK04.1
DEVICE_VARIANT := C1
SOC := qcom-ipq4019
DEVICE_DTS := qcom-ipq4019-ap.dk04.1-c1
KERNEL_INSTALL := 1
KERNEL_SIZE := 4048k
BLOCKSIZE := 128k
PAGESIZE := 2048
BOARD_NAME := ap-dk04.1-c1
DEFAULT := n
endef
TARGET_DEVICES += qcom_ap-dk04.1-c1
define Device/qxwlan_e2600ac-c1
$(call Device/FitImage)
DEVICE_VENDOR := Qxwlan
DEVICE_MODEL := E2600AC
DEVICE_VARIANT := C1
BOARD_NAME := e2600ac-c1
SOC := qcom-ipq4019
KERNEL_SIZE := 4096k
IMAGE_SIZE := 31232k
IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | append-metadata
DEVICE_PACKAGES := ipq-wifi-qxwlan_e2600ac
DEFAULT := n
endef
TARGET_DEVICES += qxwlan_e2600ac-c1
define Device/qxwlan_e2600ac-c2
$(call Device/FitImage)
$(call Device/UbiFit)
DEVICE_VENDOR := Qxwlan
DEVICE_MODEL := E2600AC
DEVICE_VARIANT := C2
SOC := qcom-ipq4019
KERNEL_INSTALL := 1
BLOCKSIZE := 128k
PAGESIZE := 2048
DEVICE_PACKAGES := ipq-wifi-qxwlan_e2600ac
endef
TARGET_DEVICES += qxwlan_e2600ac-c2
define Device/teltonika_rutx10
$(call Device/FitImage)
$(call Device/UbiFit)
DEVICE_VENDOR := Teltonika
DEVICE_MODEL := RUTX10
SOC := qcom-ipq4018
DEVICE_DTS_CONFIG := config@5
KERNEL_INSTALL := 1
BLOCKSIZE := 128k
PAGESIZE := 2048
FILESYSTEMS := squashfs
IMAGE/nand-factory.ubi := append-ubi | qsdk-ipq-factory-nand | append-rutx-metadata
DEVICE_PACKAGES := ipq-wifi-teltonika_rutx kmod-bluetooth
endef
TARGET_DEVICES += teltonika_rutx10
define Device/unielec_u4019-32m
$(call Device/FitImage)
DEVICE_VENDOR := Unielec
DEVICE_MODEL := U4019
DEVICE_VARIANT := 32M
BOARD_NAME := u4019-32m
SOC := qcom-ipq4019
KERNEL_SIZE := 4096k
IMAGE_SIZE := 31232k
IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | append-metadata
DEFAULT := n
endef
TARGET_DEVICES += unielec_u4019-32m
define Device/zyxel_nbg6617
$(call Device/FitImageLzma)
DEVICE_VENDOR := ZyXEL
DEVICE_MODEL := NBG6617
SOC := qcom-ipq4018
KERNEL_SIZE := 4096k
ROOTFS_SIZE := 24960k
RAS_BOARD := NBG6617
RAS_ROOTFS_SIZE := 19840k
RAS_VERSION := "$(VERSION_DIST) $(REVISION)"
IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | append-metadata
IMAGES += factory.bin
# The ZyXEL firmware allows flashing thru the web-gui only when the rootfs is
# at least as large as the one of the initial firmware image (not the current
# one on the device). This only applies to the Web-UI, the bootlaoder ignores
# this minimum-size. However, the larger image can be flashed both ways.
IMAGE/factory.bin := append-rootfs | pad-rootfs | pad-to 64k | check-size $$$$(ROOTFS_SIZE) | zyxel-ras-image separate-kernel
IMAGE/sysupgrade.bin/squashfs := append-rootfs | pad-rootfs | check-size $$$$(ROOTFS_SIZE) | sysupgrade-tar rootfs=$$$$@ | append-metadata
DEVICE_PACKAGES := kmod-usb-ledtrig-usbport
endef
TARGET_DEVICES += zyxel_nbg6617
define Device/zyxel_wre6606
$(call Device/FitImage)
DEVICE_VENDOR := ZyXEL
DEVICE_MODEL := WRE6606
DEVICE_DTS_CONFIG := config@4
SOC := qcom-ipq4018
IMAGE_SIZE := 13184k
IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | check-size | append-metadata
DEVICE_PACKAGES := -kmod-ath10k-ct kmod-ath10k-ct-smallbuffers
endef
TARGET_DEVICES += zyxel_wre6606
Reference in New Issue View Git Blame Copy Permalink