ExternalVendorCode/openwrt
1
0
Fork 0
mirror of https://github.com/openwrt/openwrt.git synced 2025-01-01 11:36:49 +00:00
Code Issues Actions 2 Packages Projects Releases Wiki Activity
45c9923edf
openwrt/target/linux/ath79/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
Piotr Dymacz 45c9923edf ath79: add support for YunCore XD4200 and A782 
YunCore XD4200 ('XD4200_W6.0' marking on PCB) is Qualcomm/Atheros based
(QCA9563, QCA9886, QCA8334) dual-band, Wave-2 AC1200 ceiling AP with PoE
(802.3at) support. A782 model ('T750_V5.1' marking on PCB) is a smaller
version of the XD4200, with similar specification but lower TX power.

Specification:

- QCA9563 (775 MHz)
- 128 MB of RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- 2x 10/100/1000 Mbps Ethernet (QCA8334), with 802.3at PoE support (WAN)
- Wi-Fi 2.4 GHz:
  - XD4200: 2T2R (QCA9563), with ext. PA (SKY65174-21) and LNA
  - A782: 2T2R (QCA9563), with ext. FEM (SKY85329-11)
- Wi-Fi 5 GHz:
  - XD4200: 2T2R (QCA9886), with ext. FEM (SKY85728-11)
  - A782: 2T2R (QCA9886), with ext. FEM (SKY85735-11)
- LEDs:
  - XD4200: 5x (2x driven by SOC, 1x driven by AC radio, 2x Ethernet)
  - A782: 3x (1x RGB, driven by SOC and radio, 2x Ethernet)
- 1x button (reset)
- 1x UART (4-pin, 2.54 mm pitch) header on PCB
- 1x DC jack (12 V)

Flash instructions:

If your device comes with generic QSDK based firmware, you can login
over telnet (login: root, empty password, default IP: 192.168.188.253),
issue first (important!) 'fw_setenv' command and then perform regular
upgrade, using 'sysupgrade -n -F ...' (you can use 'wget' to download
image to the device, SSH server is not available):

  fw_setenv bootcmd "bootm 0x9f050000 || bootm 0x9fe80000"
  sysupgrade -n -F openwrt-...-yuncore_...-squashfs-sysupgrade.bin

In case your device runs firmware with YunCore custom GUI, you can use
U-Boot recovery mode:

1. Set a static IP 192.168.0.141/24 on PC and start TFTP server with
   'tftp' image renamed to 'upgrade.bin'
2. Power the device with reset button pressed and release it after 5-7
   seconds, recovery mode should start downloading image from server
   (unfortunately, there is no visible indication that recovery got
   enabled - in case of problems check TFTP server logs)

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
(backported from commit e5d4c09667)
2019-11-26 18:17:39 +01:00

223 lines
5.6 KiB
Bash
Raw Blame History

#!/bin/sh
. /lib/functions/k2t.sh
# xor multiple hex values of the same length
xor() {
local val
local ret="0x$1"
local retlen=${#1}
shift
while [ -n "$1" ]; do
val="0x$1"
ret=$((ret ^ val))
shift
done
printf "%0${retlen}x" "$ret"
}
ath10kcal_die() {
echo "ath10cal: " "$*"
exit 1
}
ath10kcal_from_file() {
local source=$1
local offset=$2
local count=$3
dd if=$source of=/lib/firmware/$FIRMWARE iflag=skip_bytes bs=$count skip=$offset count=1 2>/dev/null || \
ath10kcal_die "failed to extract calibration data from $source"
}
ath10kcal_extract() {
local part=$1
local offset=$2
local count=$3
local mtd
mtd=$(find_mtd_chardev $part)
[ -n "$mtd" ] || \
ath10kcal_die "no mtd device found for partition $part"
dd if=$mtd of=/lib/firmware/$FIRMWARE iflag=skip_bytes bs=$count skip=$offset count=1 2>/dev/null || \
ath10kcal_die "failed to extract calibration data from $mtd"
}
ath10kcal_patch_mac() {
local mac=$1
[ -z "$mac" ] && return
macaddr_2bin $mac | dd of=/lib/firmware/$FIRMWARE conv=notrunc oflag=seek_bytes bs=6 seek=6 count=1
}
ath10kcal_patch_mac_crc() {
local mac=$1
local mac_offset=6
local chksum_offset=2
local xor_mac
local xor_fw_mac
local xor_fw_chksum
xor_fw_mac=$(hexdump -v -n 6 -s $mac_offset -e '/1 "%02x"' /lib/firmware/$FIRMWARE)
xor_fw_mac="${xor_fw_mac:0:4} ${xor_fw_mac:4:4} ${xor_fw_mac:8:4}"
ath10kcal_patch_mac "$mac" && {
xor_mac=${mac//:/}
xor_mac="${xor_mac:0:4} ${xor_mac:4:4} ${xor_mac:8:4}"
xor_fw_chksum=$(hexdump -v -n 2 -s $chksum_offset -e '/1 "%02x"' /lib/firmware/$FIRMWARE)
xor_fw_chksum=$(xor $xor_fw_chksum $xor_fw_mac $xor_mac)
printf "%b" "\x${xor_fw_chksum:0:2}\x${xor_fw_chksum:2:2}" | \
dd of=/lib/firmware/$FIRMWARE conv=notrunc bs=1 seek=$chksum_offset count=2
}
}
[ -e /lib/firmware/$FIRMWARE ] && exit 0
. /lib/functions.sh
. /lib/functions/system.sh
board=$(board_name)
case "$FIRMWARE" in
"ath10k/cal-pci-0000:00:00.0.bin")
case $board in
devolo,dvl1200e|\
devolo,dvl1200i|\
devolo,dvl1750c|\
devolo,dvl1750e|\
devolo,dvl1750i|\
devolo,dvl1750x)
ath10kcal_extract "art" 20480 2116
ath10kcal_patch_mac_crc $(macaddr_add $(mtd_get_mac_binary art 0) -1)
;;
dlink,dir-859-a1)
ath10kcal_extract "art" 20480 2116
ath10kcal_patch_mac $(mtd_get_mac_ascii devdata "wlan5mac")
;;
elecom,wrc-1750ghbk2-i)
ath10kcal_extract "art" 20480 2116
;;
engenius,ecb1750)
ath10kcal_extract "art" 20480 2116
ath10kcal_patch_mac $(mtd_get_mac_ascii u-boot-env athaddr)
;;
engenius,epg5000|\
iodata,wn-ac1167dgr|\
iodata,wn-ac1600dgr2)
ath10kcal_extract "art" 20480 2116
ath10kcal_patch_mac $(macaddr_add $(mtd_get_mac_ascii u-boot-env ethaddr) +1)
;;
engenius,ews511ap)
ath10kcal_extract "art" 20480 2116
ath10kcal_patch_mac $(macaddr_add $(cat /sys/class/net/eth0/address) +1)
;;
glinet,gl-ar750s)
ath10kcal_extract "art" 20480 2116
ath10kcal_patch_mac $(macaddr_add $(mtd_get_mac_binary art 0) +1)
;;
glinet,gl-x750)
ath10kcal_extract "art" 20480 2116
ath10kcal_patch_mac $(macaddr_add $(mtd_get_mac_binary art 0) +2)
;;
nec,wg800hp)
ath10kcal_extract "art" 20480 2116
ath10kcal_patch_mac_crc $(mtd_get_mac_text board_data 2176)
;;
ocedo,koala|\
ocedo,ursus)
ath10kcal_extract "art" 20480 2116
ath10kcal_patch_mac $(mtd_get_mac_binary art 12)
;;
openmesh,om5p-ac-v2)
ath10kcal_extract "art" 20480 2116
ath10kcal_patch_mac $(macaddr_add $(cat /sys/class/net/eth0/address) +16)
;;
tplink,archer-a7-v5|\
tplink,archer-c2-v3|\
tplink,archer-c7-v4|\
tplink,archer-c7-v5|\
tplink,archer-c25-v1)
ath10kcal_extract "art" 20480 2116
ath10kcal_patch_mac $(macaddr_add $(mtd_get_mac_binary info 8) -1)
;;
tplink,archer-c5-v1|\
tplink,archer-c7-v2)
ath10kcal_extract "art" 20480 2116
ath10kcal_patch_mac $(macaddr_add $(mtd_get_mac_binary u-boot 0x1fc00) -1)
;;
tplink,archer-d50-v1)
ath10kcal_extract "art" 20480 2116
ath10kcal_patch_mac $(macaddr_add $(mtd_get_mac_binary romfile 0xf100) +2)
;;
tplink,re350k-v1)
ath10kcal_extract "art" 20480 2116
ath10kcal_patch_mac $(macaddr_add $(mtd_get_mac_binary config 0x10008) +2)
;;
tplink,re450-v2)
ath10kcal_extract "art" 20480 2116
ath10kcal_patch_mac $(macaddr_add $(mtd_get_mac_binary info 8) +1)
;;
ubnt,unifiac-lite|\
ubnt,unifiac-lr|\
ubnt,unifiac-mesh|\
ubnt,unifiac-mesh-pro|\
ubnt,lap-120|\
ubnt,nanobeam-ac|\
ubnt,nanostation-ac|\
ubnt,nanostation-ac-loco|\
ubnt,unifiac-pro)
ath10kcal_extract "EEPROM" 20480 2116
;;
yuncore,a770)
ath10kcal_extract "art" 20480 2116
;;
esac
;;
"ath10k/pre-cal-pci-0000:00:00.0.bin")
case $board in
nec,wg1200cr)
ath10kcal_extract "art" 20480 12064
ath10kcal_patch_mac_crc $(mtd_get_mac_ascii devdata wlan5mac)
ln -sf /lib/firmware/ath10k/pre-cal-pci-0000\:00\:00.0.bin \
/lib/firmware/ath10k/QCA9888/hw2.0/board.bin
;;
netgear,ex6400|\
netgear,ex7300)
ath10kcal_extract "caldata" 20480 12064
ath10kcal_patch_mac $(mtd_get_mac_binary caldata 12)
;;
phicomm,k2t)
ath10kcal_extract "art" 20480 12064
ath10kcal_patch_mac_crc $(k2t_get_mac "5g_mac")
ln -sf /lib/firmware/ath10k/pre-cal-pci-0000\:00\:00.0.bin \
/lib/firmware/ath10k/QCA9888/hw2.0/board.bin
;;
tplink,archer-c58-v1|\
tplink,archer-c59-v1|\
tplink,archer-c60-v1|\
tplink,archer-c60-v2|\
tplink,archer-c6-v2)
ath10kcal_extract "art" 20480 12064
ath10kcal_patch_mac_crc $(macaddr_add $(mtd_get_mac_binary mac 8) -1)
ln -sf /lib/firmware/ath10k/pre-cal-pci-0000\:00\:00.0.bin \
/lib/firmware/ath10k/QCA9888/hw2.0/board.bin
;;
yuncore,a782|\
yuncore,xd4200)
ath10kcal_extract "art" 20480 12064
ln -sf /lib/firmware/ath10k/pre-cal-pci-0000\:00\:00.0.bin \
/lib/firmware/ath10k/QCA9888/hw2.0/board.bin
;;
esac
;;
*)
exit 1
;;
esac
Reference in New Issue View Git Blame Copy Permalink