mirror of
https://github.com/openwrt/openwrt.git
synced 2024-12-27 09:12:39 +00:00
61b4018763
Changes made in switch nodes ind42c9cecommit causes problem with correct mvsw61xx detection. This commit undo that changes. mvsw61xx is platform driver, so it need to be in main root of dts. Fixes:d42c9ce326("kirkwood: add kernel 4.19 support") Tested-by: Marcin Fedan <mfedan@gmail.com> [EA4500] Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
145 lines
2.5 KiB
Diff
145 lines
2.5 KiB
Diff
--- a/arch/arm/boot/dts/kirkwood-linksys-viper.dts
|
|
+++ b/arch/arm/boot/dts/kirkwood-linksys-viper.dts
|
|
@@ -24,6 +24,10 @@
|
|
};
|
|
|
|
aliases {
|
|
+ led-boot = &led_white_health;
|
|
+ led-failsafe = &led_white_health;
|
|
+ led-running = &led_white_health;
|
|
+ led-upgrade = &led_white_health;
|
|
serial0 = &uart0;
|
|
};
|
|
|
|
@@ -56,9 +60,10 @@
|
|
pinctrl-0 = < &pmx_led_white_health &pmx_led_white_pulse >;
|
|
pinctrl-names = "default";
|
|
|
|
- white-health {
|
|
+ led_white_health: white-health {
|
|
label = "viper:white:health";
|
|
gpios = <&gpio0 7 GPIO_ACTIVE_HIGH>;
|
|
+ default-state = "on";
|
|
};
|
|
|
|
white-pulse {
|
|
@@ -67,9 +72,18 @@
|
|
};
|
|
};
|
|
|
|
- dsa {
|
|
- status = "disabled";
|
|
+ mvsw61xx {
|
|
+ compatible = "marvell,88e6171";
|
|
+ status = "okay";
|
|
+ reg = <0x10>;
|
|
+
|
|
+ mii-bus = <&mdio>;
|
|
+ cpu-port-0 = <5>;
|
|
+ cpu-port-1 = <6>;
|
|
+ is-indirect;
|
|
+ };
|
|
|
|
+ dsa {
|
|
compatible = "marvell,dsa";
|
|
#address-cells = <2>;
|
|
#size-cells = <0>;
|
|
@@ -161,22 +175,22 @@
|
|
};
|
|
|
|
partition@200000 {
|
|
- label = "kernel";
|
|
+ label = "kernel1";
|
|
reg = <0x200000 0x2A0000>;
|
|
};
|
|
|
|
partition@4a0000 {
|
|
- label = "rootfs";
|
|
+ label = "rootfs1";
|
|
reg = <0x4A0000 0x1760000>;
|
|
};
|
|
|
|
partition@1c00000 {
|
|
- label = "alt_kernel";
|
|
+ label = "kernel2";
|
|
reg = <0x1C00000 0x2A0000>;
|
|
};
|
|
|
|
partition@1ea0000 {
|
|
- label = "alt_rootfs";
|
|
+ label = "rootfs2";
|
|
reg = <0x1EA0000 0x1760000>;
|
|
};
|
|
|
|
@@ -207,53 +221,6 @@
|
|
|
|
&mdio {
|
|
status = "okay";
|
|
-
|
|
- switch@10 {
|
|
- compatible = "marvell,mv88e6085";
|
|
- #address-cells = <1>;
|
|
- #size-cells = <0>;
|
|
- reg = <16>;
|
|
-
|
|
- ports {
|
|
- #address-cells = <1>;
|
|
- #size-cells = <0>;
|
|
-
|
|
- port@0 {
|
|
- reg = <0>;
|
|
- label = "ethernet1";
|
|
- };
|
|
-
|
|
- port@1 {
|
|
- reg = <1>;
|
|
- label = "ethernet2";
|
|
- };
|
|
-
|
|
- port@2 {
|
|
- reg = <2>;
|
|
- label = "ethernet3";
|
|
- };
|
|
-
|
|
- port@3 {
|
|
- reg = <3>;
|
|
- label = "ethernet4";
|
|
- };
|
|
-
|
|
- port@4 {
|
|
- reg = <4>;
|
|
- label = "internet";
|
|
- };
|
|
-
|
|
- port@5 {
|
|
- reg = <5>;
|
|
- label = "cpu";
|
|
- ethernet = <ð0port>;
|
|
- fixed-link {
|
|
- speed = <1000>;
|
|
- full-duplex;
|
|
- };
|
|
- };
|
|
- };
|
|
- };
|
|
};
|
|
|
|
&uart0 {
|
|
@@ -272,10 +239,14 @@
|
|
};
|
|
|
|
/* eth1 is connected to the switch at port 6. However DSA only supports a
|
|
- * single CPU port. So leave this port disabled to avoid confusion.
|
|
+ * single CPU port. Upstream uses DSA so they disable this port to avoid confusion.
|
|
*/
|
|
ð1 {
|
|
- status = "disabled";
|
|
+ status = "okay";
|
|
+ ethernet1-port@0 {
|
|
+ speed = <1000>;
|
|
+ duplex = <1>;
|
|
+ };
|
|
};
|
|
|
|
/* There is no battery on the board, so the RTC does not keep
|