mirror of
https://github.com/openwrt/openwrt.git
synced 2024-12-29 01:59:02 +00:00
04d3308b62
This patch adds support for GL.iNet GL-B1300 Specification: - SOC: IPQ4028 / QCA Dakota - RAM: 256 MiB - FLASH: 32 MiB - ETH: Qualcomm Atheros QCA8075 Gigabit Switch (2 x LAN, 1 x WAN) - USB: 1 x 3.0 (via Synopsys DesignWare DWC3 controller in the SoC) - WLAN1: Qualcomm Atheros QCA4028 2.4GHz 802.11bgn 2:2x2 - WLAN2: Qualcomm Atheros QCA4028 5GHz 802.11a/n/ac 2:2x2 - INPUT: one reset and one WPS button - LEDS: 3 leds: Power, WIFI(only for 2.4G currently), and one reserved - UART: 1 x UART on PCB (3.3V, TX, RX, GND) - 115200 8N1 Installation: Method 1: - use serial port to stop uboot - uboot command: run lf Method 2: - push down reset button and power on - wait until three leds constantly on then release - upgrade by uboot web at http://192.168.1.1 Note: - the sysupgrade image need to be renamed to lede-gl-b1300.bin in both method. - the sysupgrade image can be automatically downloaded if tftp server at 192.168.1.2 have that file. - the wifi led will be flashing when writing image. Signed-off-by: Dongming Han <handongming@gl-inet.com>
127 lines
2.7 KiB
Bash
127 lines
2.7 KiB
Bash
#!/bin/sh
|
|
|
|
ath10kcal_die() {
|
|
echo "ath10cal: " "$*"
|
|
exit 1
|
|
}
|
|
|
|
ath10kcal_from_file() {
|
|
local source=$1
|
|
local offset=$2
|
|
local count=$3
|
|
|
|
dd if=$source of=/lib/firmware/$FIRMWARE bs=1 skip=$offset count=$count 2>/dev/null || \
|
|
ath10kcal_die "failed to extract calibration data from $source"
|
|
}
|
|
|
|
ath10kcal_extract() {
|
|
local part=$1
|
|
local offset=$2
|
|
local count=$3
|
|
local mtd
|
|
|
|
mtd=$(find_mtd_chardev $part)
|
|
[ -n "$mtd" ] || \
|
|
ath10kcal_die "no mtd device found for partition $part"
|
|
|
|
dd if=$mtd of=/lib/firmware/$FIRMWARE bs=1 skip=$offset count=$count 2>/dev/null || \
|
|
ath10kcal_die "failed to extract calibration data from $mtd"
|
|
}
|
|
|
|
ath10kcal_patch_mac() {
|
|
local mac=$1
|
|
|
|
[ -z "$mac" ] && return
|
|
|
|
macaddr_2bin $mac | dd of=/lib/firmware/$FIRMWARE conv=notrunc bs=1 seek=6 count=6
|
|
}
|
|
|
|
[ -e /lib/firmware/$FIRMWARE ] && exit 0
|
|
|
|
. /lib/functions.sh
|
|
. /lib/functions/system.sh
|
|
|
|
board=$(board_name)
|
|
|
|
|
|
case "$FIRMWARE" in
|
|
"ath10k/pre-cal-ahb-a000000.wifi.bin")
|
|
case "$board" in
|
|
avm,fritzbox-4040)
|
|
/usr/bin/fritz_cal_extract -i 1 -s 0x400 -e 0x207 -l 12064 -o /lib/firmware/$FIRMWARE $(find_mtd_chardev "urlader_config")
|
|
;;
|
|
openmesh,a42)
|
|
ath10kcal_extract "0:ART" 4096 12064
|
|
;;
|
|
glinet,gl-b1300 |\
|
|
qcom,ap-dk01.1-c1)
|
|
ath10kcal_extract "ART" 4096 12064
|
|
;;
|
|
esac
|
|
;;
|
|
"ath10k/pre-cal-ahb-a800000.wifi.bin")
|
|
case "$board" in
|
|
avm,fritzbox-4040)
|
|
/usr/bin/fritz_cal_extract -i 1 -s 0x400 -e 0x208 -l 12064 -o /lib/firmware/$FIRMWARE $(find_mtd_chardev "urlader_config")
|
|
;;
|
|
openmesh,a42)
|
|
ath10kcal_extract "0:ART" 20480 12064
|
|
;;
|
|
glinet,gl-b1300 |\
|
|
qcom,ap-dk01.1-c1)
|
|
ath10kcal_extract "ART" 20480 12064
|
|
;;
|
|
esac
|
|
;;
|
|
|
|
"ath10k/pre-cal-pci-0000:01:00.0.bin")
|
|
case $board in
|
|
linksys,ea8500)
|
|
hw_mac_addr=$(mtd_get_mac_ascii devinfo hw_mac_addr)
|
|
ath10kcal_extract "art" 4096 12064
|
|
;;
|
|
netgear,d7800 |\
|
|
netgear,r7500v2 |\
|
|
netgear,r7800)
|
|
ath10kcal_extract "art" 4096 12064
|
|
;;
|
|
tplink,c2600)
|
|
ath10kcal_extract "radio" 4096 12064
|
|
# ath10kcal_patch_mac $(macaddr_add $(mtd_get_mac_binary default-mac 8) -1)
|
|
;;
|
|
tplink,vr2600v)
|
|
ath10kcal_extract "ART" 4096 12064
|
|
;;
|
|
zyxel,nbg6817)
|
|
ath10kcal_extract "0:ART" 4096 12064
|
|
;;
|
|
esac
|
|
;;
|
|
"ath10k/pre-cal-pci-0001:01:00.0.bin")
|
|
case $board in
|
|
linksys,ea8500)
|
|
hw_mac_addr=$(mtd_get_mac_ascii devinfo hw_mac_addr)
|
|
ath10kcal_extract "art" 20480 12064
|
|
;;
|
|
netgear,d7800 |\
|
|
netgear,r7500v2 |\
|
|
netgear,r7800)
|
|
ath10kcal_extract "art" 20480 12064
|
|
;;
|
|
tplink,c2600)
|
|
ath10kcal_extract "radio" 20480 12064
|
|
# ath10kcal_patch_mac $(macaddr_add $(mtd_get_mac_binary default-mac 8) -2)
|
|
;;
|
|
tplink,vr2600v)
|
|
ath10kcal_extract "ART" 20480 12064
|
|
;;
|
|
zyxel,nbg6817)
|
|
ath10kcal_extract "0:ART" 20480 12064
|
|
;;
|
|
esac
|
|
;;
|
|
*)
|
|
exit 1
|
|
;;
|
|
esac
|