mirror of
https://github.com/openwrt/openwrt.git
synced 2024-12-22 15:02:32 +00:00
35aecc9d4a
SoC: AR9344 RAM: 128MB Flash: 16MiB SPI NOR 5GHz WiFi: AR9382 PCIe 2x2:2 802.11n 2.4GHz WiFi: AR9344 (SoC) AHB 2x2:2 802.11n 5x Fast ethernet via SoC switch (green LEDs) 1x USB 2.0 4x front LEDs from SoC GPIO 1x front WPS button from SoC GPIO 1x bottom reset button from SoC GPIO UART header JP1, 115200 no parity 1 stop TX GND VCC (N/P) RX Flash factory image via "emergency room" recovery: - Configure your computer with a static IP 192.168.1.123/24 - Connect to LAN port on the N600 switch - Hold reset putton - Power on, holding reset until the power LED blinks slowly - Visit http://192.168.1.1/ and upload OpenWrt factory image - Wait at least 5 minutes for flashing, reboot and key generation - Visit http://192.168.1.1/ (OpenWrt LuCI) and upload OpenWrt sysupgrade image Signed-off-by: Ryan Mounce <ryan@mounce.com.au> [dt leds preparations] Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
109 lines
1.9 KiB
Plaintext
109 lines
1.9 KiB
Plaintext
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
|
|
|
#include "ar9344_wd_mynet-nxxx.dtsi"
|
|
#include <dt-bindings/leds/common.h>
|
|
|
|
/ {
|
|
model = "Western Digital My Net N600";
|
|
compatible = "wd,mynet-n600", "qca,ar9344";
|
|
|
|
aliases {
|
|
led-boot = &led_power;
|
|
led-failsafe = &led_power;
|
|
led-running = &led_power;
|
|
led-upgrade = &led_power;
|
|
};
|
|
|
|
leds {
|
|
compatible = "gpio-leds";
|
|
|
|
led-0 {
|
|
color = <LED_COLOR_ID_BLUE>;
|
|
function = LED_FUNCTION_WLAN;
|
|
gpios = <&gpio 0 GPIO_ACTIVE_HIGH>;
|
|
};
|
|
|
|
led_power: led-1 {
|
|
label = "blue:power";
|
|
color = <LED_COLOR_ID_BLUE>;
|
|
function = LED_FUNCTION_POWER;
|
|
gpios = <&gpio 11 GPIO_ACTIVE_HIGH>;
|
|
};
|
|
|
|
led-2 {
|
|
color = <LED_COLOR_ID_BLUE>;
|
|
function = LED_FUNCTION_WAN;
|
|
gpios = <&gpio 12 GPIO_ACTIVE_HIGH>;
|
|
};
|
|
|
|
led-3 {
|
|
color = <LED_COLOR_ID_BLUE>;
|
|
function = LED_FUNCTION_WPS;
|
|
gpios = <&gpio 13 GPIO_ACTIVE_HIGH>;
|
|
};
|
|
};
|
|
|
|
keys {
|
|
compatible = "gpio-keys";
|
|
|
|
reset {
|
|
linux,code = <KEY_RESTART>;
|
|
gpios = <&gpio 16 GPIO_ACTIVE_LOW>;
|
|
};
|
|
|
|
wps {
|
|
linux,code = <KEY_WPS_BUTTON>;
|
|
gpios = <&gpio 17 GPIO_ACTIVE_LOW>;
|
|
};
|
|
};
|
|
};
|
|
|
|
&gpio {
|
|
gpio_ext_lna0 {
|
|
gpio-hog;
|
|
gpios = <14 0>;
|
|
output-high;
|
|
line-name = "ext:lna0";
|
|
};
|
|
|
|
gpio_ext_lna1 {
|
|
gpio-hog;
|
|
gpios = <15 0>;
|
|
output-high;
|
|
line-name = "ext:lna1";
|
|
};
|
|
};
|
|
|
|
&pinmux {
|
|
pmx_led_switch: pinmux_led_switch {
|
|
pinctrl-single,bits =
|
|
<0x0 0x2c2b2a00 0xffffff00>, /* GPIO1-3 default to PHY2-4 */
|
|
<0x4 0x00000029 0x000000ff>; /* GPIO4 default to PHY1 */
|
|
};
|
|
};
|
|
|
|
&builtin_switch {
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&pmx_led_switch>;
|
|
};
|
|
|
|
&usb {
|
|
status = "okay";
|
|
};
|
|
|
|
ð0 {
|
|
status = "okay";
|
|
|
|
phy-handle = <&swphy0>;
|
|
|
|
gmac-config {
|
|
device = <&gmac>;
|
|
switch-phy-swap = <1>;
|
|
switch-only-mode = <1>;
|
|
};
|
|
};
|
|
|
|
ð1 {
|
|
status = "okay";
|
|
};
|