mirror of
https://github.com/openwrt/openwrt.git
synced 2024-12-22 15:02:32 +00:00
35f6d79513
Hardware
--------
SoC: Freescale P1010
RAM: 512MB
FLASH: 1 MB SPI-NOR
512 MB NAND
ETH: 3x Gigabite Ethernet (Atheros AR8033)
SERIAL: Cisco RJ-45 (115200 8N1)
RTC: Battery-Backed RTC (I2C)
Installation
------------
1. Patch U-Boot by dumping the content of the SPI-Flash using a SPI
programmer. The SHA1 hash for the U-Boot password is currently
unknown.
A tool for patching U-Boot is available at
https://github.com/blocktrron/t10-uboot-patcher/
You can also patch the unknown password yourself. The SHA1 hash is
E597301A1D89FF3F6D318DBF4DBA0A5ABC5ECBEA
2. Interrupt the bootmenu by pressing CTRL+C. A password prompt appears.
The patched password is '1234' (without quotation marks)
3. Download the OpenWrt initramfs image. Copy it to a TFTP server
reachable at 10.0.1.13/24 and rename it to uImage.
4. Connect the TFTP server to ethernet port 0 of the Watchguard T10.
5. Download and boot the initramfs image by entering "tftpboot; bootm;"
in U-Boot.
6. After OpenWrt booted, create a UBI volume on the old data partition.
The "ubi" mtd partition should be mtd7, check this using
$ cat /proc/mtd
Create a UBI partition by executing
$ ubiformat /dev/mtd7 -y
7. Increase the loadable kernel-size of U-Boot by executing
$ fw_setenv SysAKernSize 800000
8. Transfer the OpenWrt sysupgrade image to the Watchguard T10 using
scp. Install the image by using sysupgrade:
$ sysupgrade -n <path-to-sysupgrade>
Note: The LAN ports of the T10 are 1 & 2 while 0 is WAN. You might
have to change the ethernet-port.
9. OpenWrt should now boot from the internal NAND. Enjoy.
Signed-off-by: David Bauer <mail@david-bauer.net>
30 lines
1.0 KiB
Diff
30 lines
1.0 KiB
Diff
--- a/arch/powerpc/platforms/85xx/Kconfig
|
|
+++ b/arch/powerpc/platforms/85xx/Kconfig
|
|
@@ -92,6 +92,16 @@ config WS_AP3825I
|
|
This board is a Concurrent Dual-Band wireless access point with a
|
|
Freescale P1020 SoC.
|
|
|
|
+config FIREBOX_T10
|
|
+ bool "Watchguard Firebox T10"
|
|
+ select DEFAULT_UIMAGE
|
|
+ select ARCH_REQUIRE_GPIOLIB
|
|
+ select GPIO_MPC8XXX
|
|
+ help
|
|
+ This option enables support for the Watchguard Firebox T10 board.
|
|
+ This board is a VPN Gateway-Router with a
|
|
+ Freescale P1010 SoC.
|
|
+
|
|
config MPC8540_ADS
|
|
bool "Freescale MPC8540 ADS"
|
|
select DEFAULT_UIMAGE
|
|
--- a/arch/powerpc/platforms/85xx/Makefile
|
|
+++ b/arch/powerpc/platforms/85xx/Makefile
|
|
@@ -28,6 +28,7 @@ obj-$(CONFIG_PANDA) += panda.o
|
|
obj-$(CONFIG_TWR_P102x) += twr_p102x.o
|
|
obj-$(CONFIG_WS_AP3710I) += ws-ap3710i.o
|
|
obj-$(CONFIG_WS_AP3825I) += ws-ap3825i.o
|
|
+obj-$(CONFIG_FIREBOX_T10) += firebox_t10.o
|
|
obj-$(CONFIG_CORENET_GENERIC) += corenet_generic.o
|
|
obj-$(CONFIG_FB_FSL_DIU) += t1042rdb_diu.o
|
|
obj-$(CONFIG_RED_15W_REV1) += red15w_rev1.o
|