mirror of
https://github.com/openwrt/openwrt.git
synced 2024-12-28 01:28:59 +00:00
c6ddf8d502
Many changes were done in drivers/pinctrl/bcm/pinctrl-bcm2835.c between
5.4.171 and 5.4.179.
The following 3 patches do not apply any more:
* target/linux/bcm27xx/patches-5.4/950-0316-pinctrl-bcm2835-Add-support-for-BCM2711-pull-up-func.patch
This was already integrated in kernel v5.4-rc1, it was never needed.
* target/linux/bcm27xx/patches-5.4/950-0328-Revert-pinctrl-bcm2835-Pass-irqchip-when-adding-gpio.patch
* target/linux/bcm27xx/patches-5.4/950-0362-pinctrl-bcm2835-Change-init-order-for-gpio-hogs.patch
I think these were done to fix the problem which was really fixed in
commit 75278f1aff5e ("pinctrl: bcm2835: Change init order for gpio
hogs") from v5.4.175
target/linux/generic/backport-5.4/716-v5.5-net-sfp-move-fwnode-parsing-into-sfp-bus-layer.patch
Move fwnode_device_is_available to the same position as in kernel 5.10.
target/linux/layerscape/patches-5.4/302-dts-0083-arm64-ls1028a-qds-correct-bus-of-rtc.patch
Applied in commit 65816c1034769e714edb70f59a33bc5472d9e55f ("arm64: dts:
ls1028a-qds: move rtc node to the correct i2c bus")
Compile-tested: lantiq/xrx200, bcm27xx/bcm2710
Run-tested: lantiq/xrx200
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
71 lines
2.4 KiB
Diff
71 lines
2.4 KiB
Diff
From 507c4d749a1bbc3eb5c364dda61ac6bf95026cf1 Mon Sep 17 00:00:00 2001
|
|
From: Phil Elwell <phil@raspberrypi.com>
|
|
Date: Fri, 25 Sep 2020 15:07:23 +0100
|
|
Subject: [PATCH] net: bcmgenet: Reset RBUF on first open
|
|
|
|
If the RBUF logic is not reset when the kernel starts then there
|
|
may be some data left over from any network boot loader. If the
|
|
64-byte packet headers are enabled then this can be fatal.
|
|
|
|
Extend bcmgenet_dma_disable to do perform the reset, but not when
|
|
called from bcmgenet_resume in order to preserve a wake packet.
|
|
|
|
N.B. This different handling of resume is just based on a hunch -
|
|
why else wouldn't one reset the RBUF as well as the TBUF? If this
|
|
isn't the case then it's easy to change the patch to make the RBUF
|
|
reset unconditional.
|
|
|
|
See: https://github.com/raspberrypi/linux/issues/3850
|
|
|
|
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
|
|
---
|
|
drivers/net/ethernet/broadcom/genet/bcmgenet.c | 16 ++++++++++++----
|
|
1 file changed, 12 insertions(+), 4 deletions(-)
|
|
|
|
--- a/drivers/net/ethernet/broadcom/genet/bcmgenet.c
|
|
+++ b/drivers/net/ethernet/broadcom/genet/bcmgenet.c
|
|
@@ -2791,7 +2791,7 @@ static void bcmgenet_set_hw_addr(struct
|
|
}
|
|
|
|
/* Returns a reusable dma control register value */
|
|
-static u32 bcmgenet_dma_disable(struct bcmgenet_priv *priv)
|
|
+static u32 bcmgenet_dma_disable(struct bcmgenet_priv *priv, bool flush_rx)
|
|
{
|
|
unsigned int i;
|
|
u32 reg;
|
|
@@ -2816,6 +2816,14 @@ static u32 bcmgenet_dma_disable(struct b
|
|
udelay(10);
|
|
bcmgenet_umac_writel(priv, 0, UMAC_TX_FLUSH);
|
|
|
|
+ if (flush_rx) {
|
|
+ reg = bcmgenet_rbuf_ctrl_get(priv);
|
|
+ bcmgenet_rbuf_ctrl_set(priv, reg | BIT(0));
|
|
+ udelay(10);
|
|
+ bcmgenet_rbuf_ctrl_set(priv, reg);
|
|
+ udelay(10);
|
|
+ }
|
|
+
|
|
return dma_ctrl;
|
|
}
|
|
|
|
@@ -2911,8 +2919,8 @@ static int bcmgenet_open(struct net_devi
|
|
|
|
bcmgenet_set_hw_addr(priv, dev->dev_addr);
|
|
|
|
- /* Disable RX/TX DMA and flush TX queues */
|
|
- dma_ctrl = bcmgenet_dma_disable(priv);
|
|
+ /* Disable RX/TX DMA and flush TX and RX queues */
|
|
+ dma_ctrl = bcmgenet_dma_disable(priv, true);
|
|
|
|
/* Reinitialize TDMA and RDMA and SW housekeeping */
|
|
ret = bcmgenet_init_dma(priv);
|
|
@@ -3667,7 +3675,7 @@ static int bcmgenet_resume(struct device
|
|
bcmgenet_power_up(priv, GENET_POWER_WOL_MAGIC);
|
|
|
|
/* Disable RX/TX DMA and flush TX queues */
|
|
- dma_ctrl = bcmgenet_dma_disable(priv);
|
|
+ dma_ctrl = bcmgenet_dma_disable(priv, false);
|
|
|
|
/* Reinitialize TDMA and RDMA and SW housekeeping */
|
|
ret = bcmgenet_init_dma(priv);
|