mirror of
https://github.com/openwrt/openwrt.git
synced 2024-12-30 18:47:06 +00:00
af329ec389
Hardware -------- CPU: Freescale P1020 2xe500 PPC RAM: 256M DDR3 (Micron MT41J64M16JT-15E:G "D9MNJ") NAND: 128M (Micron 2CA1) BTN: 1x Reset LED: Power - ETH - Radio1 - Radio2 UART: RJ-45 Cisco Pinout - 115200 8N1 Installation ------------ NOTE: You can find a repo with up-to-date instructions as well as the required files here: https://github.com/blocktrron/msm460-flashing Required files ============== You need a command-files as well as a U-Boot image. The command-file has the following content (padded to 131072 bytes). If you copy paste these, remove the newlines! ``` U-BOOT setenv ethaddr 02:03:04:05:06:07; setenv ipaddr 192.168.1.1; setenv serverip 192.168.1.66; tftpboot 0x3000000 msm460-uboot.bin; nand device; nand erase 0 0xC0000; nand write 0x3000000 0x0 0xC0000; reset ``` You can download the required U-Boot from this repository: https://github.com/blocktrron/u-boot-msm/releases Preparation =========== Prepare a TFTP server serving two files: - U-Boot NAND image as `msm460-uboot.bin`. - OpenWrt factory image as `msm460-factory.bin` - Command-file names `commands.tftp` You can start a TFTP server in the current directory using dnsmasq: ```bash sudo dnsmasq --no-daemon --listen-address=0.0.0.0 \ --port=0 --enable-tftp=enxd0 --tftp-root="$(pwd)" \ --user=root --group=root ``` Replace `enxd0` with the name of your network interface. Procedure ========= 1. Assign yourself the IP-Address 192.168.1.66/24. 3. Connect the Router to the PC while keeping the reset button pressed. 4. The LEDs will eventually begin to flash. They will start to flash faster after around 15 seconds. 5. Release the reset button. 6. Start a new shell 7. Make sure you are currently in the directory where the tftp server is located. 8. Run the following command: ```bash tftp 192.168.1.1 -m binary -c put commands.tftp nflashd.cccc9999 ``` You get the message "Transfer timed out." To find out if you have been successful, please check the blinking LED Pattern. Signed-off-by: David Bauer <mail@david-bauer.net>
125 lines
4.6 KiB
Makefile
125 lines
4.6 KiB
Makefile
define Build/MultiImage
|
|
rm -rf $@.fakerd $@.new
|
|
|
|
dd if=/dev/zero of=$@.fakerd bs=32 count=1 conv=sync
|
|
|
|
-$(STAGING_DIR_HOST)/bin/mkimage -A $(LINUX_KARCH) -O linux -T multi -C $(1) \
|
|
-a $(KERNEL_LOADADDR) -e $(KERNEL_ENTRY) -n '$(BOARD_NAME) initramfs' \
|
|
-d $@:$@.fakerd:$(KDIR)/image-$(firstword $(DEVICE_DTS)).dtb $@.new
|
|
mv $@.new $@
|
|
rm -rf $@.fakerd
|
|
endef
|
|
|
|
define Device/aerohive_hiveap-330
|
|
DEVICE_VENDOR := Aerohive
|
|
DEVICE_MODEL := HiveAP-330
|
|
DEVICE_ALT0_VENDOR := Aerohive
|
|
DEVICE_ALT0_MODEL := HiveAP-350
|
|
DEVICE_PACKAGES := kmod-tpm-i2c-atmel kmod-hwmon-lm70
|
|
BLOCKSIZE := 128k
|
|
KERNEL := kernel-bin | uImage none
|
|
KERNEL_INITRAMFS := kernel-bin | uImage none
|
|
KERNEL_NAME := simpleImage.hiveap-330
|
|
KERNEL_SIZE := 16m
|
|
IMAGES := sysupgrade.bin
|
|
KERNEL_ENTRY := 0x1500000
|
|
KERNEL_LOADADDR := 0x1500000
|
|
# append-dtb is still needed, as otherwise u-boot bootm complains
|
|
# about not having a FDT to edit.
|
|
IMAGE/sysupgrade.bin := append-dtb | pad-to 256k | append-kernel | \
|
|
append-rootfs | pad-rootfs | check-size | append-metadata
|
|
IMAGE_SIZE = 63m
|
|
DEVICE_COMPAT_VERSION := 2.0
|
|
DEVICE_COMPAT_MESSAGE := \n$\
|
|
!The partitioning of the HiveAP 330 has changed! \n$\
|
|
To upgrade, please take a look at the install instructions over \
|
|
at the device's wiki: <https://openwrt.org/toh/aerohive/hiveap-330> \n$\
|
|
An abridged version for the console is provided here for comfort. \n$\
|
|
Run the following script into a shell on the device and retry this \
|
|
sysupgrade again: \n$\
|
|
cat <<- "EOF" > /tmp/uboot-fix.sh; sh /tmp/uboot-fix.sh \n$\
|
|
. /lib/functions.sh \n$\
|
|
. /lib/functions/system.sh \n$\
|
|
opkg update && opkg install uboot-envtools kmod-mtd-rw || exit 2 \n$\
|
|
insmod mtd-rw i_want_a_brick=y || exit 3 \n$\
|
|
echo "/dev/mtd$$$$(find_mtd_index u-boot-env) 0x0 0x20000 0x10000" > "/etc/fw_env.config" \n$\
|
|
fw_setenv owrt_boot 'setenv bootargs console=ttyS0,9600;bootm 0xEC040000 - 0xEC000000' \n$\
|
|
cp "/dev/mtd$$$$(find_mtd_index 'u-boot')" /tmp/uboot \n$\
|
|
cp /tmp/uboot /tmp/uboot_patched \n$\
|
|
strings -td < /tmp/uboot | grep '^ *[0-9]* *\\(run owrt_boot\\|setenv bootargs\\).*cp\\.l' | \n$\
|
|
awk '{print $$$$1}' | \n$\
|
|
while read offset; do \n$\
|
|
echo -n "run owrt_boot; " | dd of=/tmp/uboot_patched bs=1 seek=$$$${offset} conv=notrunc \n$\
|
|
done \n$\
|
|
mtd write /tmp/uboot_patched u-boot \n$\
|
|
uci set system.@system[0].compat_version=2.0; uci commit; \n$\
|
|
EOF \n$\
|
|
\n$\
|
|
Note that if this fails, you will need to use the serial console \n$\
|
|
to re-install OpenWrt. \n$\
|
|
Note that after this sysupgrade, the AP will be unavailable for 7 \n$\
|
|
minutes to reformat flash."
|
|
|
|
endef
|
|
TARGET_DEVICES += aerohive_hiveap-330
|
|
|
|
define Device/enterasys_ws-ap3710i
|
|
DEVICE_VENDOR := Enterasys
|
|
DEVICE_MODEL := WS-AP3710i
|
|
BLOCKSIZE := 128k
|
|
KERNEL_NAME := simpleImage.ws-ap3710i
|
|
KERNEL_ENTRY := 0x1500000
|
|
KERNEL_LOADADDR := 0x1500000
|
|
KERNEL = kernel-bin | uImage none
|
|
KERNEL_INITRAMFS := kernel-bin | uImage none
|
|
IMAGES := sysupgrade.bin
|
|
IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | append-metadata
|
|
endef
|
|
TARGET_DEVICES += enterasys_ws-ap3710i
|
|
|
|
define Device/extreme-networks_ws-ap3825i
|
|
DEVICE_VENDOR := Extreme Networks
|
|
DEVICE_MODEL := WS-AP3825i
|
|
DEVICE_PACKAGES := kmod-ath10k-ct ath10k-firmware-qca988x-ct
|
|
BLOCKSIZE := 128k
|
|
KERNEL_NAME := simpleImage.ws-ap3825i
|
|
KERNEL_ENTRY := 0x1500000
|
|
KERNEL_LOADADDR := 0x1500000
|
|
KERNEL = kernel-bin | fit none $(KDIR)/image-$$(DEVICE_DTS).dtb
|
|
IMAGES := sysupgrade.bin
|
|
IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | append-metadata
|
|
endef
|
|
TARGET_DEVICES += extreme-networks_ws-ap3825i
|
|
|
|
define Device/hpe_msm460
|
|
DEVICE_VENDOR := Hewlett-Packard
|
|
DEVICE_MODEL := MSM460
|
|
KERNEL = kernel-bin | fit none $(KDIR)/image-$$(DEVICE_DTS).dtb
|
|
KERNEL_NAME := zImage.la3000000
|
|
KERNEL_ENTRY := 0x3000000
|
|
KERNEL_LOADADDR := 0x3000000
|
|
BLOCKSIZE := 128k
|
|
PAGESIZE := 2048
|
|
SUBPAGESIZE := 2048
|
|
KERNEL_IN_UBI := 1
|
|
UBINIZE_OPTS := -E 5
|
|
IMAGES := factory.bin sysupgrade.bin
|
|
IMAGE/factory.bin := append-ubi
|
|
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
|
|
endef
|
|
TARGET_DEVICES += hpe_msm460
|
|
|
|
define Device/ocedo_panda
|
|
DEVICE_VENDOR := OCEDO
|
|
DEVICE_MODEL := Panda
|
|
DEVICE_PACKAGES := kmod-rtc-ds1307
|
|
KERNEL = kernel-bin | gzip | fit gzip $(KDIR)/image-$$(DEVICE_DTS).dtb
|
|
PAGESIZE := 2048
|
|
SUBPAGESIZE := 512
|
|
BLOCKSIZE := 128k
|
|
IMAGES := fdt.bin sysupgrade.bin
|
|
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
|
|
IMAGE/fdt.bin := append-dtb
|
|
endef
|
|
TARGET_DEVICES += ocedo_panda
|