openwrt/target/linux/mediatek/dts/mt7981b-cudy-tr3000-v1.dts

// SPDX-License-Identifier: (GPL-2.0 OR MIT)

/dts-v1/;

#include <dt-bindings/leds/common.h>

#include "mt7981.dtsi"

/ {
	model = "Cudy TR3000 v1";
	compatible = "cudy,tr3000-v1", "mediatek,mt7981-spim-snand-rfb";

	aliases {
		label-mac-device = &gmac1;
		led-boot = &led_status;
		led-failsafe = &led_status;
		led-running = &led_status;
		led-upgrade = &led_status;
		serial0 = &uart0;
	};

	chosen {
		stdout-path = "serial0:115200n8";
	};

	gpio-keys {
		compatible = "gpio-keys";

		reset {
			label = "reset";
			linux,code = <KEY_RESTART>;
			gpios = <&pio 1 GPIO_ACTIVE_LOW>;
		};

		mode {
			label = "mode";
			linux,input-type = <EV_SW>;
			linux,code = <BTN_0>;
			gpios = <&pio 0 GPIO_ACTIVE_LOW>;
			debounce-interval = <60>;
		};
	};

	leds {
		compatible = "gpio-leds";

		led_status: led_0 {
			function = LED_FUNCTION_POWER;
			color = <LED_COLOR_ID_RED>;
			gpios = <&pio 11 GPIO_ACTIVE_LOW>;
		};

		led_1 {
			function = LED_FUNCTION_STATUS;
			color = <LED_COLOR_ID_WHITE>;
			gpios = <&pio 10 GPIO_ACTIVE_LOW>;
		};

	};

	usb_vbus: regulator-usb {
		compatible = "regulator-fixed";

		regulator-name = "usb-vbus";
		regulator-min-microvolt = <5000000>;
		regulator-max-microvolt = <5000000>;

		gpios = <&pio 9 GPIO_ACTIVE_LOW>;
		regulator-boot-on;
	};
};

&uart0 {
	status = "okay";
};

&watchdog {
	status = "okay";
};

&eth {
	pinctrl-names = "default";
	pinctrl-0 = <&mdio_pins>;

	status = "okay";

	gmac0: mac@0 {
		compatible = "mediatek,eth-mac";
		reg = <0>;
		phy-mode = "2500base-x";
		phy-handle = <&phy1>;
		nvmem-cell-names = "mac-address";
		nvmem-cells = <&macaddr_bdinfo_de00 1>;
	};

	gmac1: mac@1 {
		compatible = "mediatek,eth-mac";
		reg = <1>;
		phy-mode = "gmii";
		phy-handle = <&int_gbe_phy>;
		nvmem-cell-names = "mac-address";
		nvmem-cells = <&macaddr_bdinfo_de00 0>;
	};
};

&mdio_bus {
	phy1: phy@1 {
		reg = <1>;
		compatible = "ethernet-phy-ieee802.3-c45";
		phy-mode = "2500base-x";
		reset-gpios = <&pio 39 GPIO_ACTIVE_LOW>;
		interrupts = <38 IRQ_TYPE_LEVEL_LOW>;
		reset-assert-us = <100000>;
		reset-deassert-us = <100000>;
		realtek,aldps-enable;
	};
};

&spi0 {
	pinctrl-names = "default";
	pinctrl-0 = <&spi0_flash_pins>;
	status = "okay";

	spi_nand: flash@0 {
		#address-cells = <1>;
		#size-cells = <1>;
		compatible = "spi-nand";
		reg = <0>;
		spi-max-frequency = <52000000>;

		spi-cal-enable;
		spi-cal-mode = "read-data";
		spi-cal-datalen = <7>;
		spi-cal-data = /bits/ 8 <0x53 0x50 0x49 0x4E 0x41 0x4E 0x44>;
		spi-cal-addrlen = <5>;
		spi-cal-addr = /bits/ 32 <0x0 0x0 0x0 0x0 0x0>;

		spi-tx-bus-width = <4>;
		spi-rx-bus-width = <4>;
		mediatek,nmbm;
		mediatek,bmt-max-ratio = <1>;
		mediatek,bmt-max-reserved-blocks = <64>;

		partitions {
			compatible = "fixed-partitions";
			#address-cells = <1>;
			#size-cells = <1>;

			partition@0 {
				label = "BL2";
				reg = <0x00000 0x0100000>;
				read-only;
			};

			partition@100000 {
				label = "u-boot-env";
				reg = <0x0100000 0x0080000>;
				read-only;
			};

			factory: partition@180000 {
				label = "Factory";
				reg = <0x180000 0x0200000>;
				read-only;
				nvmem-layout {
					compatible = "fixed-layout";
					#address-cells = <1>;
					#size-cells = <1>;

					eeprom_factory_0: eeprom@0 {
						reg = <0x0 0x1000>;
					};
				};
			};

			partition@380000 {
				label = "bdinfo";
				reg = <0x380000 0x0040000>;
				read-only;
				nvmem-layout {
					compatible = "fixed-layout";
					#address-cells = <1>;
					#size-cells = <1>;

					macaddr_bdinfo_de00: macaddr@de00 {
						compatible = "mac-base";
						reg = <0xde00 0x6>;
						#nvmem-cell-cells = <1>;
					};
				};

			};

			partition@3C0000 {
				label = "FIP";
				reg = <0x3C0000 0x0200000>;
				read-only;
			};

			partition@580000 {
				label = "ubi";
				reg = <0x5C0000 0x4000000>;
				compatible = "linux,ubi";
			};
		};
	};
};


&pio {
	spi0_flash_pins: spi0-pins {
		mux {
			function = "spi";
			groups = "spi0", "spi0_wp_hold";
		};
	};
};

&usb_phy {
	status = "okay";
};

&xhci {
	status = "okay";
	vbus-supply = <&usb_vbus>;
};

&wifi {
	status = "okay";
	nvmem-cells = <&eeprom_factory_0>;
	nvmem-cell-names = "eeprom";
};