mirror of
https://github.com/openwrt/openwrt.git
synced 2024-12-23 15:32:33 +00:00
f5d2c91415
TP-Link Archer D50 v1 is a dual-band AC1200 router + modem.
The router section is based on Qualcomm/Atheros QCA9531 + QCA9882.
The "DSL" section is based on BCM6318 but it's currently not supported.
Internally eth0 is connected to the Broadcom CPU.
Router section - Specification:
CPU: QCA9531 650/600/200 MHz (CPU/DDR/AHB)
RAM: 64 MB (DDR2)
Flash: 8 MB (SPI NOR)
Wifi 2.4GHz: QCA9531 2T2R
Wifi 5GHz: QCA9982 2T2R
4x 10/100 Mbps Ethernet
8x LED, 3x button
UART header on PCB
Known issues:
DSL not working (eth0) (WIP)
UART connection
---------------
J2 HEADER (Qualcomm CPU)
. TX
. RX
. GND
O VCC
J16 HEADER (Broadcom CPU)
O VCC
. GND
. RX
. TX
The following instructions require a connection to the J2 UART header.
Flash instruction under U-Boot, using UART
------------------------------------------
1. Press any key to stop autobooting and obtain U-Boot CLI access.
2. Setup ip addresses for U-Boot and your tftp server.
3. Issue below commands:
tftpboot 0x81000000 openwrt-ath79-generic-tplink_archer-d50-v1-squashfs-sysupgrade.bin
erase 0x9f020000 +$filesize
cp.b 0x81000000 0x9f020000 $filesize
reset
Initramfs instruction under U-Boot for testing, using UART
----------------------------------------------------------
1. Press any key to stop autobooting and obtain U-Boot CLI access.
2. Setup ip addresses for U-Boot and your tftp server.
3. Issue below commands:
tftpboot 0x81000000 openwrt-ath79-generic-tplink_archer-d50-v1-initramfs-kernel.bin
bootm 0x81000000
Restore the original firmware
-----------------------------
0. Backup every partition using the OpenWrt web interface
1. Download the OEM firmware from the TP-Link website
2. Extract the bin file in a folder (eg. Archer_D50v1_0.8.0_1.3_up_boot(170223)_full_2017-02-24_09.37.45.bin)
3. Remove the U-Boot and the Broadcom image part from the file.
Issue the following command:
dd if="Archer_D50v1_0.8.0_1.3_up_boot(170223)_full_2017-02-24_09.37.45.bin" of="Archer_D50v1_0.8.0_1.3_up_boot(170223)_full_2017-02-24_09.37.45.bin.mod" skip=257 bs=512 count=15616
4. Double check the .mod file size. It must be 7995392 bytes.
5. Flash it using the OpenWrt web interface. Force the update if needed.
WARNING: Remember to NOT keep settings.
5b. (Alternative to 5.) Flash it using the U-Boot and UART connection.
Issue below commands in the U-Boot:
tftpboot 0x81000000 Archer_D50v1_0.8.0_1.3_up_boot(170223)_full_2017-02-24_09.37.45.bin.mod
erase 0x9f020000 +$filesize
cp.b 0x81000000 0x9f020000 $filesize
reset
Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [removed
default-state = "off", it's already the default, added pcie node,
fixed typo]
206 lines
5.2 KiB
Bash
206 lines
5.2 KiB
Bash
#!/bin/sh
|
|
|
|
. /lib/functions/k2t.sh
|
|
|
|
# xor multiple hex values of the same length
|
|
xor() {
|
|
local val
|
|
local ret="0x$1"
|
|
local retlen=${#1}
|
|
|
|
shift
|
|
while [ -n "$1" ]; do
|
|
val="0x$1"
|
|
ret=$((ret ^ val))
|
|
shift
|
|
done
|
|
|
|
printf "%0${retlen}x" "$ret"
|
|
}
|
|
|
|
ath10kcal_die() {
|
|
echo "ath10cal: " "$*"
|
|
exit 1
|
|
}
|
|
|
|
ath10kcal_from_file() {
|
|
local source=$1
|
|
local offset=$2
|
|
local count=$3
|
|
|
|
dd if=$source of=/lib/firmware/$FIRMWARE iflag=skip_bytes bs=$count skip=$offset count=1 2>/dev/null || \
|
|
ath10kcal_die "failed to extract calibration data from $source"
|
|
}
|
|
|
|
ath10kcal_extract() {
|
|
local part=$1
|
|
local offset=$2
|
|
local count=$3
|
|
local mtd
|
|
|
|
mtd=$(find_mtd_chardev $part)
|
|
[ -n "$mtd" ] || \
|
|
ath10kcal_die "no mtd device found for partition $part"
|
|
|
|
dd if=$mtd of=/lib/firmware/$FIRMWARE iflag=skip_bytes bs=$count skip=$offset count=1 2>/dev/null || \
|
|
ath10kcal_die "failed to extract calibration data from $mtd"
|
|
}
|
|
|
|
ath10kcal_patch_mac() {
|
|
local mac=$1
|
|
|
|
[ -z "$mac" ] && return
|
|
|
|
macaddr_2bin $mac | dd of=/lib/firmware/$FIRMWARE conv=notrunc oflag=seek_bytes bs=6 seek=6 count=1
|
|
}
|
|
|
|
ath10kcal_patch_mac_crc() {
|
|
local mac=$1
|
|
local mac_offset=6
|
|
local chksum_offset=2
|
|
local xor_mac
|
|
local xor_fw_mac
|
|
local xor_fw_chksum
|
|
|
|
xor_fw_mac=$(hexdump -v -n 6 -s $mac_offset -e '/1 "%02x"' /lib/firmware/$FIRMWARE)
|
|
xor_fw_mac="${xor_fw_mac:0:4} ${xor_fw_mac:4:4} ${xor_fw_mac:8:4}"
|
|
|
|
ath10kcal_patch_mac "$mac" && {
|
|
xor_mac=${mac//:/}
|
|
xor_mac="${xor_mac:0:4} ${xor_mac:4:4} ${xor_mac:8:4}"
|
|
|
|
xor_fw_chksum=$(hexdump -v -n 2 -s $chksum_offset -e '/1 "%02x"' /lib/firmware/$FIRMWARE)
|
|
xor_fw_chksum=$(xor $xor_fw_chksum $xor_fw_mac $xor_mac)
|
|
|
|
printf "%b" "\x${xor_fw_chksum:0:2}\x${xor_fw_chksum:2:2}" | \
|
|
dd of=/lib/firmware/$FIRMWARE conv=notrunc bs=1 seek=$chksum_offset count=2
|
|
}
|
|
}
|
|
|
|
[ -e /lib/firmware/$FIRMWARE ] && exit 0
|
|
|
|
. /lib/functions.sh
|
|
. /lib/functions/system.sh
|
|
|
|
board=$(board_name)
|
|
|
|
case "$FIRMWARE" in
|
|
"ath10k/cal-pci-0000:00:00.0.bin")
|
|
case $board in
|
|
devolo,dvl1200e|\
|
|
devolo,dvl1200i|\
|
|
devolo,dvl1750c|\
|
|
devolo,dvl1750e|\
|
|
devolo,dvl1750i)
|
|
ath10kcal_extract "art" 20480 2116
|
|
ath10kcal_patch_mac_crc $(macaddr_add $(mtd_get_mac_binary art 0) -1)
|
|
;;
|
|
dlink,dir-859-a1)
|
|
ath10kcal_extract "art" 20480 2116
|
|
ath10kcal_patch_mac $(mtd_get_mac_ascii devdata "wlan5mac")
|
|
;;
|
|
elecom,wrc-1750ghbk2-i)
|
|
ath10kcal_extract "ART" 20480 2116
|
|
;;
|
|
engenius,ecb1750)
|
|
ath10kcal_extract "art" 20480 2116
|
|
ath10kcal_patch_mac $(mtd_get_mac_ascii u-boot-env athaddr)
|
|
;;
|
|
engenius,epg5000|\
|
|
iodata,wn-ac1167dgr|\
|
|
iodata,wn-ac1600dgr2)
|
|
ath10kcal_extract "art" 20480 2116
|
|
ath10kcal_patch_mac $(macaddr_add $(mtd_get_mac_ascii u-boot-env ethaddr) +1)
|
|
;;
|
|
engenius,ews511ap|\
|
|
glinet,gl-ar750s|\
|
|
glinet,gl-x750|\
|
|
tplink,re450-v2)
|
|
ath10kcal_extract "art" 20480 2116
|
|
ath10kcal_patch_mac $(macaddr_add $(cat /sys/class/net/eth0/address) +1)
|
|
;;
|
|
nec,wg800hp)
|
|
ath10kcal_extract "art" 20480 2116
|
|
ath10kcal_patch_mac_crc $(mtd_get_mac_text board_data 2176)
|
|
;;
|
|
ocedo,koala|\
|
|
ocedo,ursus)
|
|
ath10kcal_extract "art" 20480 2116
|
|
ath10kcal_patch_mac $(mtd_get_mac_binary art 12)
|
|
;;
|
|
openmesh,om5p-ac-v2)
|
|
ath10kcal_extract "ART" 20480 2116
|
|
ath10kcal_patch_mac $(macaddr_add $(cat /sys/class/net/eth0/address) +16)
|
|
;;
|
|
tplink,archer-c2-v3)
|
|
ath10kcal_extract "ART" 20480 2116
|
|
ath10kcal_patch_mac $(macaddr_add $(cat /sys/class/net/eth0/address) -1)
|
|
;;
|
|
tplink,archer-c5-v1|\
|
|
tplink,archer-c7-v2)
|
|
ath10kcal_extract "art" 20480 2116
|
|
ath10kcal_patch_mac $(macaddr_add $(cat /sys/class/net/eth1/address) -1)
|
|
;;
|
|
tplink,archer-a7-v5|\
|
|
tplink,archer-c7-v4|\
|
|
tplink,archer-c7-v5)
|
|
ath10kcal_extract "art" 20480 2116
|
|
ath10kcal_patch_mac $(macaddr_add $(cat /sys/class/net/eth0/address) -1)
|
|
;;
|
|
tplink,archer-d50-v1)
|
|
ath10kcal_extract "art" 20480 2116
|
|
ath10kcal_patch_mac $(macaddr_add $(cat /sys/class/net/eth1/address) +2)
|
|
;;
|
|
tplink,re350k-v1)
|
|
ath10kcal_extract "art" 20480 2116
|
|
ath10kcal_patch_mac $(macaddr_add $(cat /sys/class/net/eth0/address) +2)
|
|
;;
|
|
ubnt,unifiac-lite|\
|
|
ubnt,unifiac-mesh|\
|
|
ubnt,unifiac-mesh-pro|\
|
|
ubnt,lap-120|\
|
|
ubnt,nanobeam-ac|\
|
|
ubnt,nanostation-ac|\
|
|
ubnt,nanostation-ac-loco|\
|
|
ubnt,unifiac-pro)
|
|
ath10kcal_extract "EEPROM" 20480 2116
|
|
;;
|
|
yuncore,a770)
|
|
ath10kcal_extract "art" 20480 2116
|
|
;;
|
|
esac
|
|
;;
|
|
"ath10k/pre-cal-pci-0000:00:00.0.bin")
|
|
case $board in
|
|
nec,wg1200cr)
|
|
ath10kcal_extract "art" 20480 12064
|
|
ath10kcal_patch_mac_crc $(mtd_get_mac_ascii devdata wlan5mac)
|
|
ln -sf /lib/firmware/ath10k/pre-cal-pci-0000\:00\:00.0.bin \
|
|
/lib/firmware/ath10k/QCA9888/hw2.0/board.bin
|
|
;;
|
|
netgear,ex6400|\
|
|
netgear,ex7300)
|
|
ath10kcal_extract "caldata" 20480 12064
|
|
ath10kcal_patch_mac $(mtd_get_mac_binary caldata 12)
|
|
;;
|
|
phicomm,k2t)
|
|
ath10kcal_extract "art" 20480 12064
|
|
ath10kcal_patch_mac_crc $(k2t_get_mac "5g_mac")
|
|
ln -sf /lib/firmware/ath10k/pre-cal-pci-0000\:00\:00.0.bin \
|
|
/lib/firmware/ath10k/QCA9888/hw2.0/board.bin
|
|
;;
|
|
tplink,archer-c58-v1|\
|
|
tplink,archer-c59-v1|\
|
|
tplink,archer-c6-v2)
|
|
ath10kcal_extract "art" 20480 12064
|
|
ath10kcal_patch_mac_crc $(macaddr_add $(mtd_get_mac_binary mac 8) -1)
|
|
ln -sf /lib/firmware/ath10k/pre-cal-pci-0000\:00\:00.0.bin \
|
|
/lib/firmware/ath10k/QCA9888/hw2.0/board.bin
|
|
;;
|
|
esac
|
|
;;
|
|
*)
|
|
exit 1
|
|
;;
|
|
esac
|