mirror of
https://github.com/openwrt/openwrt.git
synced 2024-12-30 02:29:01 +00:00
dd1d95cb03
Device specifications:
======================
* Qualcomm/Atheros QCA9533 v2
* 650/600/217 MHz (CPU/DDR/AHB)
* 64 MB of RAM
* 16 MB of SPI NOR flash
- 2x 7 MB available; but one of the 7 MB regions is the recovery image
* 2x 10/100 Mbps Ethernet
* 1T1R 2.4 GHz Wi-Fi
* 6x GPIO-LEDs (3x wifi, 2x ethernet, 1x power)
* 1x GPIO-button (reset)
* external h/w watchdog (enabled by default)
* TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX)
* 2x fast ethernet
- eth0
+ Label: Ethernet 1
+ 24V passive POE (mode B)
- eth1
+ Label: Ethernet 2
+ 802.3af POE
+ builtin switch port 1
* 12-24V 1A DC
* external antenna
Flashing instructions:
======================
Various methods can be used to install the actual image on the flash.
Two easy ones are:
ap51-flash
----------
The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
used to transfer the image to the u-boot when the device boots up.
initramfs from TFTP
-------------------
The serial console must be used to access the u-boot shell during bootup.
It can then be used to first boot up the initramfs image from a TFTP server
(here with the IP 192.168.1.21):
setenv serverip 192.168.1.21
setenv ipaddr 192.168.1.1
tftpboot 0c00000 <filename-of-initramfs-kernel>.bin && bootm $fileaddr
The actual sysupgrade image can then be transferred (on the LAN port) to
the device via
scp <filename-of-squashfs-sysupgrade>.bin root@192.168.1.1:/tmp/
On the device, the sysupgrade must then be started using
sysupgrade -n /tmp/<filename-of-squashfs-sysupgrade>.bin
Signed-off-by: Sven Eckelmann <sven@narfation.org>
[wrap two very long lines, fix typo in comment]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
158 lines
2.7 KiB
Plaintext
158 lines
2.7 KiB
Plaintext
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
|
|
|
#include "qca953x.dtsi"
|
|
|
|
#include <dt-bindings/gpio/gpio.h>
|
|
#include <dt-bindings/input/input.h>
|
|
|
|
/ {
|
|
chosen {
|
|
/delete-property/ bootargs;
|
|
};
|
|
|
|
aliases {
|
|
led-boot = &led_power_blue;
|
|
led-failsafe = &led_power_blue;
|
|
led-running = &led_power_blue;
|
|
led-upgrade = &led_power_blue;
|
|
label-mac-device = ð0;
|
|
};
|
|
|
|
keys {
|
|
compatible = "gpio-keys";
|
|
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&jtag_disable_pins>;
|
|
|
|
reset {
|
|
label = "reset";
|
|
linux,code = <KEY_RESTART>;
|
|
gpios = <&gpio 1 GPIO_ACTIVE_LOW>;
|
|
};
|
|
};
|
|
|
|
leds {
|
|
compatible = "gpio-leds";
|
|
|
|
led_power_blue: power_blue {
|
|
label = "blue:power";
|
|
gpios = <&gpio 0 GPIO_ACTIVE_LOW>;
|
|
default-state = "on";
|
|
};
|
|
|
|
wifi_green {
|
|
label = "green:wifi";
|
|
gpios = <&gpio 2 GPIO_ACTIVE_LOW>;
|
|
linux,default-trigger = "phy0tpt";
|
|
};
|
|
|
|
wifi_yellow {
|
|
label = "yellow:wifi";
|
|
gpios = <&gpio 3 GPIO_ACTIVE_LOW>;
|
|
};
|
|
|
|
wifi_red {
|
|
label = "red:wifi";
|
|
gpios = <&gpio 4 GPIO_ACTIVE_LOW>;
|
|
};
|
|
|
|
wan_blue {
|
|
label = "blue:wan";
|
|
gpios = <&gpio 13 GPIO_ACTIVE_LOW>;
|
|
};
|
|
|
|
lan_blue {
|
|
label = "blue:lan";
|
|
gpios = <&gpio 14 GPIO_ACTIVE_LOW>;
|
|
};
|
|
};
|
|
|
|
watchdog {
|
|
compatible = "linux,wdt-gpio";
|
|
gpios = <&gpio 12 GPIO_ACTIVE_LOW>;
|
|
hw_algo = "toggle";
|
|
/* hw_margin_ms is actually 300s but driver limits it to 60s */
|
|
hw_margin_ms = <60000>;
|
|
always-running;
|
|
};
|
|
};
|
|
|
|
&uart {
|
|
status = "okay";
|
|
};
|
|
|
|
&spi {
|
|
status = "okay";
|
|
|
|
flash@0 {
|
|
compatible = "jedec,spi-nor";
|
|
reg = <0>;
|
|
spi-max-frequency = <25000000>;
|
|
|
|
/* partitions are passed via bootloader */
|
|
partitions {
|
|
compatible = "fixed-partitions";
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
|
|
partition@0 {
|
|
label = "u-boot";
|
|
reg = <0x000000 0x040000>;
|
|
read-only;
|
|
};
|
|
|
|
partition@40000 {
|
|
label = "u-boot-env";
|
|
reg = <0x040000 0x040000>;
|
|
};
|
|
|
|
partition@80000 {
|
|
label = "custom";
|
|
reg = <0x080000 0x140000>;
|
|
read-only;
|
|
};
|
|
|
|
partition@1c0000 {
|
|
label = "inactive";
|
|
reg = <0x1c0000 0x700000>;
|
|
};
|
|
|
|
partition@8c0000 {
|
|
label = "inactive2";
|
|
reg = <0x8c0000 0x700000>;
|
|
};
|
|
|
|
art: partition@fc0000 {
|
|
label = "ART";
|
|
reg = <0xfc0000 0x040000>;
|
|
read-only;
|
|
};
|
|
};
|
|
};
|
|
};
|
|
|
|
ð0 {
|
|
status = "okay";
|
|
|
|
phy-handle = <&swphy4>;
|
|
|
|
mtd-mac-address = <&art 0x0>;
|
|
};
|
|
|
|
ð1 {
|
|
/* Workaround: keep the Ethernet interfaces order/mapping correct
|
|
* (GMAC0 -> eth0, GMAC1 -> eth1, same as in old ar71xx target)
|
|
*/
|
|
compatible = "qca,qca9530-eth", "syscon", "simple-mfd";
|
|
|
|
mtd-mac-address = <&art 0x6>;
|
|
};
|
|
|
|
&wmac {
|
|
status = "okay";
|
|
|
|
mtd-cal-data = <&art 0x1000>;
|
|
mtd-mac-address = <&art 0x0>;
|
|
mtd-mac-address-increment = <2>;
|
|
};
|