mirror of
https://github.com/openwrt/openwrt.git
synced 2024-12-22 15:02:32 +00:00
3a4b751110
The uart node is enabled on all devices except one (GL-USB150 *). Thus, let's not have a few hundred nodes to enable it, but do not disable it in the first place. Where the majority of devices is using it, also move the serial0 alias to the DTSI. *) Since GL-USB150 even defines serial0 alias, the missing uart is probably just a mistake. Anyway, disable it for now so this patch stays cosmetic. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
140 lines
2.3 KiB
Plaintext
140 lines
2.3 KiB
Plaintext
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
|
|
|
#include "ar9344.dtsi"
|
|
|
|
#include <dt-bindings/gpio/gpio.h>
|
|
#include <dt-bindings/input/input.h>
|
|
|
|
/ {
|
|
compatible = "comfast,cf-e120a-v3", "qca,ar9344";
|
|
model = "COMFAST CF-E120A v3";
|
|
|
|
aliases {
|
|
led-boot = &led_rssihigh;
|
|
led-failsafe = &led_rssihigh;
|
|
led-upgrade = &led_rssihigh;
|
|
label-mac-device = ð0;
|
|
};
|
|
|
|
leds {
|
|
compatible = "gpio-leds";
|
|
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&led_rssimediumhigh_pin>;
|
|
|
|
wan {
|
|
label = "green:wan";
|
|
gpios = <&gpio 3 GPIO_ACTIVE_LOW>;
|
|
};
|
|
|
|
lan {
|
|
label = "green:lan";
|
|
gpios = <&gpio 2 GPIO_ACTIVE_LOW>;
|
|
};
|
|
|
|
wlan {
|
|
label = "green:wlan";
|
|
gpios = <&gpio 0 GPIO_ACTIVE_LOW>;
|
|
linux,default-trigger = "phy0tpt";
|
|
};
|
|
|
|
rssilow {
|
|
label = "red:rssilow";
|
|
gpios = <&gpio 14 GPIO_ACTIVE_LOW>;
|
|
};
|
|
|
|
rssimediumlow {
|
|
label = "red:rssimediumlow";
|
|
gpios = <&gpio 15 GPIO_ACTIVE_LOW>;
|
|
};
|
|
|
|
rssimediumhigh {
|
|
label = "green:rssimediumhigh";
|
|
gpios = <&gpio 16 GPIO_ACTIVE_LOW>;
|
|
};
|
|
|
|
led_rssihigh: rssihigh {
|
|
label = "green:rssihigh";
|
|
gpios = <&gpio 17 GPIO_ACTIVE_LOW>;
|
|
};
|
|
};
|
|
|
|
keys {
|
|
compatible = "gpio-keys";
|
|
|
|
reset {
|
|
label = "reset";
|
|
linux,code = <KEY_RESTART>;
|
|
gpios = <&gpio 22 GPIO_ACTIVE_LOW>;
|
|
debounce-interval = <60>;
|
|
};
|
|
};
|
|
};
|
|
|
|
&pinmux {
|
|
led_rssimediumhigh_pin: pinmux_rssimediumhigh_pin {
|
|
pinctrl-single,bits = <0x10 0x0 0xff>;
|
|
};
|
|
};
|
|
|
|
&spi {
|
|
status = "okay";
|
|
|
|
flash@0 {
|
|
compatible = "jedec,spi-nor";
|
|
reg = <0>;
|
|
spi-max-frequency = <25000000>;
|
|
|
|
partitions {
|
|
compatible = "fixed-partitions";
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
|
|
partition@0 {
|
|
label = "u-boot";
|
|
reg = <0x000000 0x010000>;
|
|
read-only;
|
|
};
|
|
|
|
art: partition@10000 {
|
|
label = "art";
|
|
reg = <0x010000 0x010000>;
|
|
read-only;
|
|
};
|
|
|
|
partition@20000 {
|
|
compatible = "denx,uimage";
|
|
label = "firmware";
|
|
reg = <0x020000 0x7d0000>;
|
|
};
|
|
|
|
partition@7f0000 {
|
|
label = "nvram";
|
|
reg = <0x7f0000 0x010000>;
|
|
read-only;
|
|
};
|
|
};
|
|
};
|
|
};
|
|
|
|
ð0 {
|
|
status = "okay";
|
|
phy-handle = <&swphy0>;
|
|
mtd-mac-address = <&art 0x0>;
|
|
|
|
gmac-config {
|
|
device = <&gmac>;
|
|
switch-phy-swap = <1>;
|
|
};
|
|
};
|
|
|
|
ð1 {
|
|
status = "okay";
|
|
mtd-mac-address = <&art 0x6>;
|
|
};
|
|
|
|
&wmac {
|
|
status = "okay";
|
|
mtd-cal-data = <&art 0x1000>;
|
|
};
|