This repository is a mirror of https://git.openwrt.org/openwrt/openwrt.git It is for reference only and is not active for check-ins. We will continue to accept Pull Requests here. They will be merged via staging trees then into openwrt.git.
Go to file
John Crispin 3991526989 ramips: use kernel 3.6.6
## Booting image at 80800000 ...
   Image Name:   MIPS OpenWrt Linux-3.6.6
   Created:      2012-11-06  14:19:54 UTC

 System Control Status = 0x20440000
   Image Type:   MIPS Linux Kernel Image (lzma compressed)
   Data Size:    3560768 Bytes =  3.4 MB
   Load Address: 80000000
   Entry Point:  80000000
   Verifying Checksum ... OK
   Uncompressing Kernel Image ... OK
No initrd
## Transferring control to Linux (at address 80000000) ...
## Giving linux memsize in MB, 32

Starting kernel ...

[    0.000000] Linux version 3.6.6 (daniel@localhost.localdomain) (gcc version 4.6.4 20121001 (prerelease) (Linaro GCC 4.6-2012.10) ) #2 Tue Nov 6 16:19:48 IST 2012
[    0.000000] bootconsole [early0] enabled
[    0.000000] CPU revision is: 0001964c (MIPS 24KEc)
[    0.000000] Ralink RT3052 id:1 rev:2 running at 384.00 MHz
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 02000000 @ 00000000 (usable)
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] Zone ranges:
[    0.000000]   Normal   [mem 0x00000000-0x01ffffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x00000000-0x01ffffff]
[    0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[    0.000000] Primary data cache 16kB, 4-way, VIPT, no aliases, linesize 32 bytes
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 8128
[    0.000000] Kernel command line:  console=ttyS1,57600n8 board=ALL0239-3G mtdparts=physmap-flash.0:192k(u-boot)ro,64k(u-boot-env)ro,64k(factory)ro,896k(kernel),6976k(rootfs),7872k@0x50000(firmware) rootfstype=squashfs,jffs2
[    0.000000] PID hash table entries: 128 (order: -3, 512 bytes)
[    0.000000] Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
[    0.000000] __ex_table already sorted, skipping sort
[    0.000000] Writing ErrCtl register=0000c388
[    0.000000] Readback ErrCtl register=0000c388
[    0.000000] Memory: 27048k/32768k available (2015k kernel code, 5720k reserved, 498k data, 2676k init, 0k highmem)
[    0.000000] SLUB: Genslabs=9, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000] NR_IRQS:48
[    0.000000] console [ttyS1] enabled, bootconsole disabled
[    0.000000] console [ttyS1] enabled, bootconsole disabled
[    0.010000] Calibrating delay loop... 255.59 BogoMIPS (lpj=1277952)
[    0.090000] pid_max: default: 32768 minimum: 301
[    0.100000] Mount-cache hash table entries: 512
[    0.110000] NET: Registered protocol family 16
[    0.120000] MIPS: machine is Allnet ALL0239-3G
[    0.140000] bio: create slab <bio-0> at 0
[    0.150000] Switching to clocksource MIPS
[    0.160000] NET: Registered protocol family 2
[    0.170000] TCP established hash table entries: 1024 (order: 1, 8192 bytes)
[    0.180000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[    0.200000] TCP: Hash tables configured (established 1024 bind 1024)
[    0.210000] TCP: reno registered
[    0.220000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    0.230000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    0.240000] NET: Registered protocol family 1
[    5.460000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    5.470000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    5.490000] msgmni has been set to 52
[    5.500000] io scheduler noop registered
[    5.510000] io scheduler deadline registered (default)
[    5.520000] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[    5.530000] serial8250: ttyS0 at MMIO 0x10000500 (irq = 13) is a 16550A
[    5.550000] serial8250: ttyS1 at MMIO 0x10000c00 (irq = 20) is a 16550A
[    5.560000] physmap platform flash device: 00800000 at bf000000
[    5.580000] physmap-flash.0: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x000001 Chip ID 0x001000
[    5.600000] Amd/Fujitsu Extended Query Table at 0x0040
[    5.610000]   Amd/Fujitsu Extended Query version 1.3.
[    5.620000] number of CFI chips: 1
[    5.620000] 6 cmdlinepart partitions found on MTD device physmap-flash.0
[    5.640000] Creating 6 MTD partitions on "physmap-flash.0":
[    5.650000] 0x000000000000-0x000000030000 : "u-boot"
[    5.660000] 0x000000030000-0x000000040000 : "u-boot-env"
[    5.680000] 0x000000040000-0x000000050000 : "factory"
[    5.690000] 0x000000050000-0x000000130000 : "kernel"
[    5.700000] 0x000000130000-0x000000800000 : "rootfs"
[    5.710000] mtd: partition "rootfs" set to be root filesystem
[    5.730000] split_squashfs: error occured while reading from "physmap-flash.0"
[    5.740000] 0x000000050000-0x000000800000 : "firmware"
[    5.760000] ramips-wdt ramips-wdt: timeout value must be 0 < timeout <= 33, using 33
[    5.780000] TCP: cubic registered
[    5.780000] NET: Registered protocol family 17
[    5.790000] 8021q: 802.1Q VLAN Support v1.8
[    5.820000] Freeing unused kernel memory: 2676k freed
[    6.490000] Button Hotplug driver version 0.4.1
- preinit -
Press the [f] key and hit [enter] to enter failsafe mode
- regular preinit -
- init -

Please press Enter to activate this console. [   10.150000] Compat-drivers backport release: compat-drivers-2012-09-04-2-gddac993
[   10.170000] Backport based on wireless-testing.git master-2012-09-07
[   10.180000] compat.git: wireless-testing.git
[   10.210000] cfg80211: Calling CRDA to update world regulatory domain
[   10.230000] cfg80211: World regulatory domain updated:
[   10.240000] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[   10.250000] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   10.270000] cfg80211:   (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[   10.280000] cfg80211:   (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[   10.300000] cfg80211:   (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   10.310000] cfg80211:   (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   10.430000] NET: Registered protocol family 10
[   10.760000] PPP generic driver version 2.4.2
[   10.820000] l2tp_core: L2TP core driver, V2.0
[   10.840000] l2tp_netlink: L2TP netlink interface
[   10.870000] sit: IPv6 over IPv4 tunneling driver
[   10.920000] ip_tables: (C) 2000-2006 Netfilter Core Team
[   11.060000] NET: Registered protocol family 24
[   11.090000] nf_conntrack version 0.5.0 (464 buckets, 1856 max)
[   11.230000] l2tp_ppp: PPPoL2TP kernel driver, V2.0
[   11.410000] ip6_tables: (C) 2000-2006 Netfilter Core Team
[   14.510000] device eth0.1 entered promiscuous mode
[   14.520000] device eth0 entered promiscuous mode
[   14.530000] IPv6: ADDRCONF(NETDEV_CHANGE): eth0.1: link becomes ready
[   14.550000] br-lan: port 1(eth0.1) entered forwarding state
[   14.560000] br-lan: port 1(eth0.1) entered forwarding state
[   16.560000] br-lan: port 1(eth0.1) entered forwarding state
[   16.600000] ramips-wdt: timeout value 60 must be 0 < timeout <= 33, using 33

BusyBox v1.19.4 (2012-11-06 13:40:37 IST) built-in shell (ash)
Enter 'help' for a list of built-in commands.

  _______                     ________        __
 |       |.-----.-----.-----.|  |  |  |.----.|  |_
 |   -   ||  _  |  -__|     ||  |  |  ||   _||   _|
 |_______||   __|_____|__|__||________||__|  |____|
          |__| W I R E L E S S   F R E E D O M
 -----------------------------------------------------
 BARRIER BREAKER (Bleeding Edge, r34079)
 -----------------------------------------------------
  * 1/2 oz Galliano         Pour all ingredients into
  * 4 oz cold Coffee        an irish coffee mug filled
  * 1 1/2 oz Dark Rum       with crushed ice. Stir.
  * 2 tsp. Creme de Cacao
 -----------------------------------------------------
root@OpenWrt:/#

SVN-Revision: 34111
2012-11-07 20:26:21 +00:00
docs update switch documentation 2012-10-12 12:13:56 +00:00
include buildroot: isolate the .install stamp files for build variants (#12279) 2012-11-07 16:15:22 +00:00
package Load schedule modules 2012-11-07 19:36:56 +00:00
scripts scrips/metadata.pl: fix broken targets with subtargets being selectable 2012-10-22 22:16:19 +00:00
target ramips: use kernel 3.6.6 2012-11-07 20:26:21 +00:00
toolchain eglibc: update to r21110 2012-10-31 17:32:43 +00:00
tools rename patch-cmdline and add code for patching DTB files into kernel images 2012-11-02 20:06:45 +00:00
.gitattributes add .gitattributes to prevent the git autocrlf option from messing with CRLF/LF in files 2012-05-08 13:30:49 +00:00
.gitignore .gitignore: Ignore Emacs editor generated files 2011-10-31 09:37:59 +00:00
BSDmakefile add missing copyright header 2007-02-26 01:05:09 +00:00
Config.in hide C++ standard library selection behind INSTALL_LIBSTDCPP 2012-10-24 13:05:07 +00:00
feeds.conf.default Add xorg feed to feeds.conf.default 2011-11-16 16:05:23 +00:00
LICENSE finally move buildroot-ng to trunk 2016-03-20 17:29:15 +01:00
Makefile Makefile: add a check to bail out early when the path to the openwrt directory contains spaces (#12344) 2012-10-21 02:00:11 +00:00
README trying to make README file a bit more helpful 2012-01-21 01:15:24 +00:00
rules.mk build: rework the package/install step - collect package install lists during package/compile, then install all packages at once 2012-10-06 16:01:06 +00:00

This is the buildsystem for the OpenWrt Linux distribution.

Please use "make menuconfig" to configure your appreciated
configuration for the toolchain and firmware.

You need to have installed gcc, binutils, patch, bzip2, flex,
make, gettext, pkg-config, unzip, libz-dev and libc headers.

Run "./scripts/feeds update" to get the latest package definitions
defined in feeds.conf / feeds.conf.default respectively
and "./scripts/feeds install" to install symlinks into "package/feeds/*".

Use "make menuconfig" to configure your image.

Simply running "make" will build your firmware.
It will download all sources, build the cross-compile toolchain, 
the kernel and all choosen applications.

You can use "scripts/flashing/flash.sh" for remotely updating your embedded
system via tftp.

The OpenWrt system is documented in docs/. You will need a LaTeX distribution
and the tex4ht package to build the documentation. Type "make -C docs/" to build it.

To build your own firmware you need to have access to a Linux, BSD or MacOSX system
(case-sensitive filesystem required). Cygwin will not be supported because of
the lack of case sensitiveness in the file system.


Sunshine!
	Your OpenWrt Project
	http://openwrt.org