mirror of
https://github.com/openwrt/openwrt.git
synced 2024-12-22 06:57:57 +00:00
8299d1f057
Rebased RPi foundation patches on linux 5.10.59, removed applied and reverted patches, wireless patches and defconfig patches. bcm2708: boot tested on RPi B+ v1.2 bcm2709: boot tested on RPi 4B v1.1 4G bcm2711: boot tested on RPi 4B v1.1 4G Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
192 lines
7.5 KiB
Diff
192 lines
7.5 KiB
Diff
From 095bad7f310809a951735d03be9d06938524a6bc Mon Sep 17 00:00:00 2001
|
|
From: Assaf Gordon <assafgordon@gmail.com>
|
|
Date: Fri, 12 Mar 2021 00:13:07 -0700
|
|
Subject: [PATCH] overlays: gpio-led: new overlay
|
|
|
|
Add generic connection between the kernel's LED framework and
|
|
RPI's GPIO pins.
|
|
|
|
Signed-off-by: Assaf Gordon <assafgordon@gmail.com>
|
|
---
|
|
arch/arm/boot/dts/overlays/Makefile | 1 +
|
|
arch/arm/boot/dts/overlays/README | 56 +++++++++++
|
|
.../boot/dts/overlays/gpio-led-overlay.dts | 97 +++++++++++++++++++
|
|
3 files changed, 154 insertions(+)
|
|
create mode 100755 arch/arm/boot/dts/overlays/gpio-led-overlay.dts
|
|
|
|
--- a/arch/arm/boot/dts/overlays/Makefile
|
|
+++ b/arch/arm/boot/dts/overlays/Makefile
|
|
@@ -54,6 +54,7 @@ dtbo-$(CONFIG_ARCH_BCM2835) += \
|
|
gpio-ir.dtbo \
|
|
gpio-ir-tx.dtbo \
|
|
gpio-key.dtbo \
|
|
+ gpio-led.dtbo \
|
|
gpio-no-bank0-irq.dtbo \
|
|
gpio-no-irq.dtbo \
|
|
gpio-poweroff.dtbo \
|
|
--- a/arch/arm/boot/dts/overlays/README
|
|
+++ b/arch/arm/boot/dts/overlays/README
|
|
@@ -914,6 +914,62 @@ Params: gpio GPIO pin
|
|
keycode Set the key code for the button
|
|
|
|
|
|
+
|
|
+Name: gpio-led
|
|
+Info: This is a generic overlay for activating LEDs (or any other component)
|
|
+ by a GPIO pin. Multiple LEDs can be set up using multiple calls to the
|
|
+ overlay. While there are many existing methods to activate LEDs on the
|
|
+ RPi, this method offers some advantages:
|
|
+ 1) Does not require any userspace programs.
|
|
+ 2) LEDs can be connected to the kernel's led-trigger framework,
|
|
+ and drive the LED based on triggers such as cpu load, heartbeat,
|
|
+ kernel panic, key input, timers and others.
|
|
+ 3) LED can be tied to the input state of another GPIO pin.
|
|
+ 4) The LED is setup early during the kernel boot process (useful
|
|
+ for cpu/heartbeat/panic triggers).
|
|
+
|
|
+ Typical electrical connection is:
|
|
+ RPI-GPIO.19 -> LED -> 300ohm resister -> RPI-GND
|
|
+ The GPIO pin number can be changed with the 'gpio=' parameter.
|
|
+
|
|
+ To control an LED from userspace, write a 0 or 1 value:
|
|
+ echo 1 > /sys/class/leds/myled1/brightness
|
|
+ The 'myled1' name can be changed with the 'label=' parameter.
|
|
+
|
|
+ To connect the LED to a kernel trigger from userspace:
|
|
+ echo cpu > /sys/class/leds/myled1/trigger
|
|
+ echo heartbeat > /sys/class/leds/myled1/trigger
|
|
+ echo none > /sys/class/leds/myled1/trigger
|
|
+ To connect the LED to GPIO.26 pin (physical pin 37):
|
|
+ echo gpio > /sys/class/leds/myled1/trigger
|
|
+ echo 26 > /sys/class/leds/myled1/gpio
|
|
+ Available triggers:
|
|
+ cat /sys/class/leds/myled1/trigger
|
|
+
|
|
+ More information about the Linux kernel LED/Trigger system:
|
|
+ https://www.kernel.org/doc/Documentation/leds/leds-class.rst
|
|
+ https://www.kernel.org/doc/Documentation/leds/ledtrig-oneshot.rst
|
|
+Load: dtoverlay=gpio-led,<param>=<val>
|
|
+Params: gpio GPIO pin connected to the LED (default 19)
|
|
+ label The label for this LED. It will appear under
|
|
+ /sys/class/leds/<label> . Default 'myled1'.
|
|
+ trigger Set the led-trigger to connect to this LED.
|
|
+ default 'none' (LED is user-controlled).
|
|
+ Some possible triggers:
|
|
+ cpu - CPU load (all CPUs)
|
|
+ cpu0 - CPU load of first CPU.
|
|
+ mmc - disk activity (all disks)
|
|
+ panic - turn on on kernel panic
|
|
+ heartbeat - indicate system health
|
|
+ gpio - connect to a GPIO input pin (note:
|
|
+ currently the GPIO PIN can not be set
|
|
+ using overlay parameters, must be
|
|
+ done in userspace, see examples above.
|
|
+ active_low Set to 1 to turn invert the LED control
|
|
+ (writing 0 to /sys/class/leds/XXX/brightness
|
|
+ will turn on the GPIO/LED). Default '0'.
|
|
+
|
|
+
|
|
Name: gpio-no-bank0-irq
|
|
Info: Use this overlay to disable GPIO interrupts for GPIOs in bank 0 (0-27),
|
|
which can be useful for UIO drivers.
|
|
--- /dev/null
|
|
+++ b/arch/arm/boot/dts/overlays/gpio-led-overlay.dts
|
|
@@ -0,0 +1,97 @@
|
|
+// SPDX-License-Identifier: GPL-2.0-or-later
|
|
+/*
|
|
+ * gpio-led - generic connection of kernel's LED framework to the RPI's GPIO.
|
|
+ * Copyright (C) 2021 House Gordon Software Company Ltd. <assafgordon@gmail.com>
|
|
+ *
|
|
+ * Based on information from:
|
|
+ * https://mjoldfield.com/atelier/2017/03/rpi-devicetree.html
|
|
+ * https://www.raspberrypi.org/documentation/configuration/device-tree.md
|
|
+ * https://www.kernel.org/doc/html/latest/leds/index.html
|
|
+ *
|
|
+ * compile with:
|
|
+ * dtc -@ -Hepapr -I dts -O dtb -o gpio-led.dtbo gpio-led-overlay.dts
|
|
+ *
|
|
+ * There will be some warnings (can be ignored):
|
|
+ * Warning (label_is_string): /__overrides__:label: property is not a string
|
|
+ * Warning (unit_address_vs_reg): /fragment@0/__overlay__/led_pins@0:
|
|
+ * node has a unit name, but no reg property
|
|
+ * Warning (unit_address_vs_reg): /fragment@1/__overlay__/leds@0:
|
|
+ * node has a unit name, but no reg property
|
|
+ * Warning (gpios_property): /__overrides__: Missing property
|
|
+ * '#gpio-cells' in node /fragment@1/__overlay__/leds@0/led
|
|
+ * or bad phandle (referred from gpio[0])
|
|
+ *
|
|
+ * Typical electrical connection is:
|
|
+ * RPI-GPIO.19 -> LED -> 300ohm resister -> RPI-GND
|
|
+ * The GPIO pin number can be changed with the 'gpio=' parameter.
|
|
+ *
|
|
+ * Test from user-space with:
|
|
+ * # if nothing is shown, the overlay file isn't found in /boot/overlays
|
|
+ * dtoverlay -a | grep gpio-led
|
|
+ *
|
|
+ * # Load the overlay
|
|
+ * dtoverlay gpio-led label=moo gpio=19
|
|
+ *
|
|
+ * # if nothing is shown, the overlay wasn't loaded successfully
|
|
+ * dtoverlay -l | grep gpio-led
|
|
+ *
|
|
+ * echo 1 > /sys/class/leds/moo/brightness
|
|
+ * echo 0 > /sys/class/leds/moo/brightness
|
|
+ * echo cpu > /sys/class/leds/moo/trigger
|
|
+ * echo heartbeat > /sys/class/leds/moo/trigger
|
|
+ *
|
|
+ * # unload the overlay
|
|
+ * dtoverlay -r gpio-led
|
|
+ *
|
|
+ * To load in /boot/config.txt add lines such as:
|
|
+ * dtoverlay=gpio-led,gpio=19,label=heart,trigger=heartbeat
|
|
+ * dtoverlay=gpio-led,gpio=26,label=brain,trigger=cpu
|
|
+ */
|
|
+
|
|
+/dts-v1/;
|
|
+/plugin/;
|
|
+
|
|
+/ {
|
|
+ compatible = "brcm,bcm2835";
|
|
+
|
|
+ fragment@0 {
|
|
+ // Configure the gpio pin controller
|
|
+ target = <&gpio>;
|
|
+ __overlay__ {
|
|
+ led_pin: led_pins@19 {
|
|
+ brcm,pins = <19>; // gpio number
|
|
+ brcm,function = <1>; // 0 = input, 1 = output
|
|
+ brcm,pull = <0>; // 0 = none, 1 = pull down, 2 = pull up
|
|
+ };
|
|
+ };
|
|
+ };
|
|
+ fragment@1 {
|
|
+ target-path = "/";
|
|
+ __overlay__ {
|
|
+ leds: leds@0 {
|
|
+ compatible = "gpio-leds";
|
|
+ pinctrl-names = "default";
|
|
+ pinctrl-0 = <&led_pin>;
|
|
+ status = "okay";
|
|
+
|
|
+ led: led {
|
|
+ label = "myled1";
|
|
+ gpios = <&gpio 19 0>;
|
|
+ linux,default-trigger = "none";
|
|
+ };
|
|
+ };
|
|
+ };
|
|
+ };
|
|
+
|
|
+ __overrides__ {
|
|
+ gpio = <&led>,"gpios:4",
|
|
+ <&leds>,"reg:0",
|
|
+ <&led_pin>,"brcm,pins:0",
|
|
+ <&led_pin>,"reg:0";
|
|
+ label = <&led>,"label";
|
|
+ active_low = <&led>,"gpios:8";
|
|
+ trigger = <&led>,"linux,default-trigger";
|
|
+ };
|
|
+
|
|
+};
|
|
+
|