mirror of
https://github.com/openwrt/openwrt.git
synced 2024-12-22 15:02:32 +00:00
8a4dc6f48c
The Ubiquiti Network airCube ISP is a cube shaped 2.4 GHz with internal
2x2 MIMO antennas. It can be supplied via a USB connector or via PoE.
There are for 10/100 Mbps ports (1 * WAN + 3 * LAN). There is an
optional PoE passthrough from the first LAN port to the WAN port.
SoC: Qualcomm / Atheros QCA9533-BL3A
RAM: 64 MB DDR2
Flash: 16 MB SPI NOR
Ethernet: 4x 10/100 Mbps (1 WAN + 3 LAN)
LEDS: 1x via a SPI controller (not yet supported)
Buttons: 1x Reset
Serial: 1x (only RX and TX); 115200 baud, 8N1
Missing points:
- LED not yet supported
- Factory upgrade via web IF or TFTP recovery not yet supported
(Needs RSA signed images, for details see PR#1958)
The serial port is on a four pin connextor labeled J1 and located
between Ethernet and USB connector. The pinout is:
1. 3V3 (out)
2. Rx (in)
3. Tx (out)
4. GND
Upgrading via serial port / U-Boot:
- Connect the serial port via a level converter
- Power the system and stop U-Boot with pressing any key when `Hit any
key to stop autoboot` is displayed. Note: Pressing space multiple
times untill U-Boot reaches that location works well.
- Connect a PC with the IP 192.168.1.100 (or some other in that net)
running a TFTP-Server to one of the LAN ports. Copy the sysupgrade
image to the server.
- Set the U-Boot server IP with
setenv serverip 192.168.1.100
- Load the flash image to RAM with
tftpboot 0x81000000 sysupgrade.bin
- Erase the flash with
erase 0x9f050000 0x9ffaffff
- Write the new flash content with
cp 0x81000000 0x9f050000 ${filesize}
- Reset the device with
reset
Signed-off-by: Christian Mauderer <oss@c-mauderer.de>
[removed full stop in subject and added lockdown note to commit message]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
96 lines
1.5 KiB
Plaintext
96 lines
1.5 KiB
Plaintext
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
|
/dts-v1/;
|
|
|
|
#include <dt-bindings/gpio/gpio.h>
|
|
#include <dt-bindings/input/input.h>
|
|
|
|
#include "qca953x.dtsi"
|
|
|
|
/ {
|
|
compatible = "ubnt,acb-isp", "qca,qca9533";
|
|
model = "Ubiquiti airCube ISP";
|
|
|
|
keys {
|
|
compatible = "gpio-keys";
|
|
|
|
reset {
|
|
label = "reset";
|
|
linux,code = <KEY_RESTART>;
|
|
gpios = <&gpio 17 GPIO_ACTIVE_LOW>;
|
|
debounce-interval = <60>;
|
|
};
|
|
};
|
|
};
|
|
|
|
&spi {
|
|
status = "okay";
|
|
num-cs = <1>;
|
|
|
|
flash@0 {
|
|
compatible = "jedec,spi-nor";
|
|
reg = <0>;
|
|
spi-max-frequency = <25000000>;
|
|
|
|
partitions {
|
|
compatible = "fixed-partitions";
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
|
|
partition@0 {
|
|
label = "u-boot";
|
|
reg = <0x000000 0x040000>;
|
|
read-only;
|
|
};
|
|
|
|
partition@40000 {
|
|
label = "u-boot-env";
|
|
reg = <0x040000 0x010000>;
|
|
read-only;
|
|
};
|
|
|
|
partition@50000 {
|
|
compatible = "denx,uimage";
|
|
label = "firmware";
|
|
reg = <0x050000 0xf60000>;
|
|
};
|
|
|
|
partition@fb0000 {
|
|
label = "cfg";
|
|
reg = <0xfb0000 0x040000>;
|
|
read-only;
|
|
};
|
|
|
|
eeprom: partition@ff0000 {
|
|
label = "EEPROM";
|
|
reg = <0xff0000 0x010000>;
|
|
read-only;
|
|
};
|
|
};
|
|
};
|
|
};
|
|
|
|
&uart {
|
|
status = "okay";
|
|
};
|
|
|
|
ð0 {
|
|
status = "okay";
|
|
mtd-mac-address = <&eeprom 0x0>;
|
|
phy-handle = <&swphy4>;
|
|
};
|
|
|
|
ð1 {
|
|
status = "okay";
|
|
mtd-mac-address = <&eeprom 0x6>;
|
|
|
|
gmac-config {
|
|
device = <&gmac>;
|
|
};
|
|
};
|
|
|
|
&wmac {
|
|
status = "okay";
|
|
mtd-cal-data = <&eeprom 0x1000>;
|
|
mtd-mac-address = <&eeprom 0x1002>;
|
|
};
|