mirror of
https://github.com/openwrt/openwrt.git
synced 2024-12-29 10:08:59 +00:00
5d0ccaf67c
This commit adds support for a dual-band AX1800 wall plug manufactured by Shenzhen Century Xinyang Tech Co., Ltd. CPU: Mediatek MT7621A (2 cores, 4 threads) RAM: 256i MiB DDR3 (Samsung K4B2G1646F-BCNB) ROM: 16 MiB SPI NOR (Winbond W25Q128JVPQ) Wired: one gigabit RJ45 port (with green/yellow non-GPIO LEDs) WiFi: Mediatek MT7905DAN + MT7975DN (DBDC 2x 2T2R) Ant.: four 2 dBi external antennas (two 2.4GHz, two 5 GHz) GPIO: tri-color status LED (GPIO 13, 14, 16); reset button (GPIO 18) Power: 12V 2-pin JST-XH on main PCB 110/220V AC to 12V1A DC on auxiliary PCB UART: 115200 8n1, SMD pads available on the PCB as J4 pinout is [3v3] (Rx) (Tx) (Gnd) MAC: 1C:BF:CE:xx:xx:xx (2.4 GHz, label) 1C:BF:CE:xx:xx:xx + 1 (ethernet [1]) 1C:BF:CE:xx:xx:xx + 2 (5 GHz) Original firmware is LEDE Reboot 17.01-SNAPSHOT (kernel 4.4.198) with a few custom packages and a non-LuCI web interface. Telnet and SSH are enabled, requiring an unknown root password [2]. Root password is also needed to access the router via UART console, but passwordless telnet can be enabled via a trivial web exploit [3] and then the root password can be removed by editing `/etc/shadow`. Installation: First upload `sysupgrade` binary via web interface at `http://192.168.188.1/settings.shtml` and wait until getting back to the home screen (select network to extend). The installation fails since the original firmware uses `swconfig` and recent versions of OpenWrt use DSA. However, the sysupgrade file is uploaded correctly and stored at `/tmp/upgrade.bin`, so it can be written to flash via the web exploit [4] (both `mtd -r write` and `sysupgrade -Fn` work fine). Passwordless telnet/ssh is not needed for installation. Alternatively, use u-boot menu to load image via TFTP. Notes: - Device model in LEDE is "MediaTek MT7621 RFB (802.11ax,SNOR)". - It is sold under several names, among them are Wodesys WD-R1802U, Fenvi F-AX1802U, and EDUP EP-2971; the Wodesys brand was selected since it is referenced in `/etc/banner` and `/etc/hosts`, and the PCB is marked "WD518A V1.0". - Instead of a standard ethernet transformer, the PCB has a few tiny SMD coils. [1] Original firmware sets ethernet MAC to 1C:BF:CE:E7:62:1D based on offset `0x3fff4` in the Factory partition; since this is the same MAC for all units, whereas WiFi MACs stored at offsets 0x6 and 0xc are unique, it was decided to use <label MAC + 1> for ethernet. [2] root:$1$7rmMiPJj$91iv9LWhfkZE/t7aCBdo.0:18388:0:99999:7::: [3] curl -X POST http://192.168.188.1/cgi-bin/adm.cgi \ -d page=Lang -d langType="en;killall telnetd;telnetd -l /bin/sh" [4] curl -X POST http://192.168.188.1/cgi-bin/adm.cgi \ -d page=Lang -d langType="en;mtd -r write /tmp/upgrade.bin firmware" Signed-off-by: Rani Hod <rani.hod@gmail.com> Link: https://github.com/openwrt/openwrt/pull/15777 Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
154 lines
2.6 KiB
Plaintext
154 lines
2.6 KiB
Plaintext
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
|
|
|
#include "mt7621.dtsi"
|
|
|
|
#include <dt-bindings/gpio/gpio.h>
|
|
#include <dt-bindings/input/input.h>
|
|
#include <dt-bindings/leds/common.h>
|
|
|
|
/ {
|
|
compatible = "wodesys,wd-r1802u", "mediatek,mt7621-soc";
|
|
model = "Wodesys WD-R1802U";
|
|
|
|
aliases {
|
|
label-mac-device = &gmac0;
|
|
led-boot = &led_blue;
|
|
led-failsafe = &led_red;
|
|
led-running = &led_green;
|
|
led-upgrade = &led_blue;
|
|
};
|
|
|
|
chosen {
|
|
bootargs = "console=ttyS0,115200";
|
|
};
|
|
|
|
gpio-keys {
|
|
compatible = "gpio-keys";
|
|
|
|
key-0 {
|
|
label = "reset";
|
|
gpios = <&gpio 18 GPIO_ACTIVE_LOW>;
|
|
linux,code = <KEY_RESTART>;
|
|
};
|
|
};
|
|
|
|
gpio-leds {
|
|
compatible = "gpio-leds";
|
|
|
|
led_green: led-0 {
|
|
color = <LED_COLOR_ID_GREEN>;
|
|
function = LED_FUNCTION_STATUS;
|
|
gpios = <&gpio 13 GPIO_ACTIVE_LOW>;
|
|
};
|
|
|
|
led_blue: led-1 {
|
|
color = <LED_COLOR_ID_BLUE>;
|
|
function = LED_FUNCTION_STATUS;
|
|
gpios = <&gpio 14 GPIO_ACTIVE_LOW>;
|
|
};
|
|
|
|
led_red: led-2 {
|
|
color = <LED_COLOR_ID_RED>;
|
|
function = LED_FUNCTION_STATUS;
|
|
gpios = <&gpio 17 GPIO_ACTIVE_LOW>;
|
|
panic-indicator;
|
|
};
|
|
};
|
|
};
|
|
|
|
&gmac0 {
|
|
nvmem-cells = <&macaddr_factory_4 1>;
|
|
nvmem-cell-names = "mac-address";
|
|
};
|
|
|
|
&pcie {
|
|
status = "okay";
|
|
};
|
|
|
|
&pcie1 {
|
|
wifi@0,0 {
|
|
compatible = "mediatek,mt76";
|
|
reg = <0x0000 0 0 0 0>;
|
|
nvmem-cells = <&eeprom_factory_0>, <&precal_factory_e10>;
|
|
nvmem-cell-names = "eeprom", "precal";
|
|
mediatek,disable-radar-background;
|
|
};
|
|
};
|
|
|
|
&spi0 {
|
|
status = "okay";
|
|
|
|
flash@0 {
|
|
compatible = "jedec,spi-nor";
|
|
reg = <0>;
|
|
spi-max-frequency = <50000000>;
|
|
|
|
partitions {
|
|
compatible = "fixed-partitions";
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
|
|
partition@0 {
|
|
label = "u-boot";
|
|
reg = <0x00000 0x30000>;
|
|
read-only;
|
|
};
|
|
|
|
/* 0x30000-0x4ffff are unused
|
|
(flash contents is 0xff) */
|
|
|
|
partition@50000 {
|
|
label = "factory";
|
|
reg = <0x50000 0x40000>;
|
|
read-only;
|
|
|
|
nvmem-layout {
|
|
compatible = "fixed-layout";
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
|
|
eeprom_factory_0: eeprom@0 {
|
|
reg = <0x0 0xe00>;
|
|
};
|
|
|
|
macaddr_factory_4: macaddr@4 { // wifi 2.4
|
|
compatible = "mac-base";
|
|
reg = <0x4 0x6>;
|
|
#nvmem-cell-cells = <1>;
|
|
};
|
|
|
|
precal_factory_e10: precal@e10 {
|
|
reg = <0xe10 0x19c10>;
|
|
};
|
|
};
|
|
};
|
|
|
|
partition@90000 {
|
|
compatible = "denx,uimage";
|
|
label = "firmware";
|
|
reg = <0x90000 0xf70000>;
|
|
};
|
|
};
|
|
};
|
|
};
|
|
|
|
&state_default {
|
|
gpio {
|
|
groups = "jtag", "wdt";
|
|
function = "gpio";
|
|
};
|
|
};
|
|
|
|
&switch0 {
|
|
ports {
|
|
port@4 {
|
|
status = "okay";
|
|
label = "lan";
|
|
};
|
|
};
|
|
};
|
|
|
|
&xhci {
|
|
status = "disabled";
|
|
};
|