mirror of
https://github.com/openwrt/openwrt.git
synced 2024-12-30 10:39:04 +00:00
9703a2adcc
Refresh all patches on top of kernel 5.10.138. The following patches were applied upstream: bcm27xx/patches-5.10/950-0311-drm-vc4-Adopt-the-dma-configuration-from-the-HVS-or-.patch bcm27xx/patches-5.10/950-0317-vc4_hdmi-Remove-firmware-logic-for-MAI-threshold-set.patch bcm27xx/patches-5.10/950-0346-drm-vc4-A-present-but-empty-dmas-disables-audio.patch bcm27xx/patches-5.10/950-0354-drm-vc4-Add-the-2711-HVS-as-a-suitable-DMA-node.patch bcm27xx/patches-5.10/950-0413-drm-vc4-hdmi-Don-t-access-the-connector-state-in-res.patch bcm27xx/patches-5.10/950-0505-vc4-drm-Avoid-full-hdmi-audio-fifo-writes.patch bcm27xx/patches-5.10/950-0512-vc4-drm-vc4_plane-Remove-subpixel-positioning-check.patch bcm27xx/patches-5.10/950-0560-drm-vc4-drv-Remove-the-DSI-pointer-in-vc4_drv.patch bcm27xx/patches-5.10/950-0561-drm-vc4-dsi-Use-snprintf-for-the-PHY-clocks-instead-.patch bcm27xx/patches-5.10/950-0562-drm-vc4-dsi-Introduce-a-variant-structure.patch bcm27xx/patches-5.10/950-0565-drm-vc4-Correct-pixel-order-for-DSI0.patch bcm27xx/patches-5.10/950-0566-drm-vc4-Register-dsi0-as-the-correct-vc4-encoder-typ.patch bcm27xx/patches-5.10/950-0567-drm-vc4-Fix-dsi0-interrupt-support.patch bcm27xx/patches-5.10/950-0568-drm-vc4-Add-correct-stop-condition-to-vc4_dsi_encode.patch bcm27xx/patches-5.10/950-0647-drm-vc4-Fix-timings-for-interlaced-modes.patch bcm27xx/patches-5.10/950-0695-drm-vc4-Fix-margin-calculations-for-the-right-bottom.patch Upstream sets the pixel clock to 340MHz now, do not set it to 600MHz any more. bcm27xx/patches-5.10/950-0576-drm-vc4-hdmi-Raise-the-maximum-clock-rate.patch Fixes:89956c6532("kernel: bump 5.10 to 5.10.138") Fixes:4209c33ae2("kernel: bump 5.10 to 5.10.137") Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
36 lines
1.1 KiB
Diff
36 lines
1.1 KiB
Diff
From 72d78ec8b6898976ea46b1c0cb9780707985cd80 Mon Sep 17 00:00:00 2001
|
|
From: Phil Elwell <phil@raspberrypi.com>
|
|
Date: Thu, 19 Aug 2021 14:28:56 +0100
|
|
Subject: [PATCH] Makefiles: dt: Always set '-@' on ARCH_BCM2835
|
|
|
|
On the BCM2835 architecture, always add the '-@' option to enable the
|
|
generation of symbols, rather than relying on DTC_FLAGS being empty
|
|
or correct.
|
|
|
|
See: https://github.com/raspberrypi/linux/issues/3846
|
|
|
|
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
|
|
---
|
|
arch/arm/boot/dts/Makefile | 2 +-
|
|
arch/arm64/boot/dts/broadcom/Makefile | 2 +-
|
|
2 files changed, 2 insertions(+), 2 deletions(-)
|
|
|
|
--- a/arch/arm/boot/dts/Makefile
|
|
+++ b/arch/arm/boot/dts/Makefile
|
|
@@ -1434,5 +1434,5 @@ subdir-y := overlays
|
|
|
|
# Enable fixups to support overlays on BCM2835 platforms
|
|
ifeq ($(CONFIG_ARCH_BCM2835),y)
|
|
- DTC_FLAGS ?= -@
|
|
+ DTC_FLAGS += -@
|
|
endif
|
|
--- a/arch/arm64/boot/dts/broadcom/Makefile
|
|
+++ b/arch/arm64/boot/dts/broadcom/Makefile
|
|
@@ -16,5 +16,5 @@ subdir-y += stingray
|
|
|
|
# Enable fixups to support overlays on BCM2835 platforms
|
|
ifeq ($(CONFIG_ARCH_BCM2835),y)
|
|
- DTC_FLAGS ?= -@
|
|
+ DTC_FLAGS += -@
|
|
endif
|