mirror of
https://github.com/openwrt/openwrt.git
synced 2025-01-11 07:22:54 +00:00
93610492b6
Netgear WAX214 is a 802.11 ax dual-band AP
with PoE. (similar to Engenius EWS357APV3)
Specifications:
• CPU: Qualcomm IPQ6010 Quad core Cortex-A53
• RAM: 512MB of DDR3
• Storage: 128MB NAND (Macronix MX30UF1G18AC)
• Ethernet: 1x 1G RJ45 port (QCA8072) PoE
• WIFI:
2.4GHz: Qualcomm QCN5022 2x2 802.11b/g/n/ax 574 Mbps PHY rate
5GHz: Qualcomm QCN5052 2x2 802.11a/b/g/n/ac/ax 1201 PHY rate
• LEDs:
4 x GPIO-controlled LEDs
- 1 Power LED (orange)
- 1 LAN LED (blue)
- 1 WIFI 5g LED (blue)
- 1 WIFI 2g LED (blue)
black_small_square Buttons: 1x soft reset
black_small_square Power: 12V DC jack or PoE (802.3af )
An populated serial header is onboard, format is
1.25mm 4p (DF13A-4P-1.25H)
RX/TX is working, bootwait is active, secure boot is not
enabled.
The root password of the stock firmware is unknown,
but failsafe mode can be entered to reset the password.
Installation Instructions:
- obtain serial access
- stop auto boot (press "4", Entr boot command line
interface)
- setenv active_fw 0 (to boot from the primary rootfs,
or set to 1 to boot from the secondary rootfs
partition)
- saveenv
- tftpboot the initramfs image
- bootm
- copy
openwrt-qualcommax-ipq60xx-netgear_wax214-squashfs-factory.ubi
to the device
- write the image to the NAND:
- cat /proc/mtd and look for rootfs partition (should
be mtd11,
or mtd12 if you choose active_fw 1)
- ubiformat /dev/mtd11 -f -y
openwrt-qualcommax-ipq60xx-netgear_wax214-squashfs-factory.ubi
- reboot
Note: the firmware is senao-based. But I was unable to build
a valid senao-header into the image.
Maybe they changed the header format and senaoFW isn't
working any more.
Signed-off-by: Dirk Buchwalder <buchwalder@posteo.de>
180 lines
6.7 KiB
Makefile
180 lines
6.7 KiB
Makefile
include $(TOPDIR)/rules.mk
|
|
include $(INCLUDE_DIR)/version.mk
|
|
|
|
PKG_NAME:=ipq-wifi
|
|
PKG_RELEASE:=1
|
|
|
|
PKG_SOURCE_PROTO:=git
|
|
PKG_SOURCE_URL=$(PROJECT_GIT)/project/firmware/qca-wireless.git
|
|
PKG_SOURCE_DATE:=2024-03-04
|
|
PKG_SOURCE_VERSION:=38c02ae4302f9cb73f6914574239fe84799caa84
|
|
PKG_MIRROR_HASH:=0f6a2dea8466ea0e8df3262bff643d60b1725f2218589c41d9f87fb37843c362
|
|
|
|
PKG_FLAGS:=nonshared
|
|
|
|
include $(INCLUDE_DIR)/package.mk
|
|
|
|
define Build/Compile
|
|
endef
|
|
|
|
# Use ath10k-bdencoder from https://github.com/qca/qca-swiss-army-knife.git
|
|
# to generate the board-* files here.
|
|
#
|
|
# This is intended to be used on an interim basis until device-specific
|
|
# board data for new devices is available through the upstream compilation
|
|
#
|
|
# Please send a mail with your device-specific board files upstream.
|
|
# You can find instructions and examples on the linux-wireless wiki:
|
|
# <https://wireless.wiki.kernel.org/en/users/drivers/ath10k/boardfiles>
|
|
|
|
ALLWIFIBOARDS:= \
|
|
8devices_mango \
|
|
arcadyan_aw1000 \
|
|
buffalo_wxr-5950ax12 \
|
|
cmcc_rm2-6 \
|
|
compex_wpq873 \
|
|
dynalink_dl-wrx36 \
|
|
edgecore_eap102 \
|
|
edimax_cax1800 \
|
|
linksys_mx4200 \
|
|
linksys_mx5300 \
|
|
netgear_lbr20 \
|
|
netgear_rax120v2 \
|
|
netgear_wax214 \
|
|
netgear_wax218 \
|
|
netgear_wax620 \
|
|
netgear_wax630 \
|
|
prpl_haze \
|
|
qnap_301w \
|
|
redmi_ax6 \
|
|
wallys_dr40x9 \
|
|
xiaomi_ax3600 \
|
|
xiaomi_ax9000 \
|
|
yyets_le1 \
|
|
yuncore_ax880 \
|
|
zte_mf269 \
|
|
zte_mf289f \
|
|
zte_mf287 \
|
|
zte_mf287plus \
|
|
zyxel_nbg7815
|
|
|
|
ALLWIFIPACKAGES:=$(foreach BOARD,$(ALLWIFIBOARDS),ipq-wifi-$(BOARD))
|
|
|
|
define Package/ipq-wifi-default
|
|
SUBMENU:=ath10k Board-Specific Overrides
|
|
SECTION:=firmware
|
|
CATEGORY:=Firmware
|
|
DEPENDS:=@(TARGET_ipq40xx||TARGET_ipq806x||TARGET_qualcommax)
|
|
TITLE:=Custom Board
|
|
endef
|
|
|
|
define ipq-wifi-install-one-to
|
|
$(INSTALL_DIR) $(2)/lib/firmware/ath10k/$(3)/
|
|
$(INSTALL_DATA) $(1) $(2)/lib/firmware/ath10k/$(3)/board-2.bin
|
|
endef
|
|
|
|
define ipq-wifi-install-ath11-one-to
|
|
$(INSTALL_DIR) $(2)/lib/firmware/ath11k/$(3)/
|
|
$(INSTALL_DATA) $(1) $(2)/lib/firmware/ath11k/$(3)/board-2.bin
|
|
endef
|
|
|
|
define ipq-wifi-install-one
|
|
$(if $(filter $(suffix $(1)),.QCA4019 .qca4019),\
|
|
$(call ipq-wifi-install-one-to,$(1),$(2),QCA4019/hw1.0),\
|
|
$(if $(filter $(suffix $(1)),.QCA9888 .qca9888),\
|
|
$(call ipq-wifi-install-one-to,$(1),$(2),QCA9888/hw2.0),\
|
|
$(if $(filter $(suffix $(1)),.QCA9889 .qca9889),\
|
|
$(call ipq-wifi-install-one-to,$(1),$(2),QCA9887/hw1.0),\
|
|
$(if $(filter $(suffix $(1)),.QCA9984 .qca9984),\
|
|
$(call ipq-wifi-install-one-to,$(1),$(2),QCA9984/hw1.0),\
|
|
$(if $(filter $(suffix $(1)),.QCA99X0 .qca99x0),\
|
|
$(call ipq-wifi-install-one-to,$(1),$(2),QCA99X0/hw2.0),\
|
|
$(if $(filter $(suffix $(1)),.IPQ6018 .ipq6018),\
|
|
$(call ipq-wifi-install-ath11-one-to,$(1),$(2),IPQ6018/hw1.0),\
|
|
$(if $(filter $(suffix $(1)),.IPQ8074 .ipq8074),\
|
|
$(call ipq-wifi-install-ath11-one-to,$(1),$(2),IPQ8074/hw2.0),\
|
|
$(if $(filter $(suffix $(1)),.QCN9074 .qcn9074),\
|
|
$(call ipq-wifi-install-ath11-one-to,$(1),$(2),QCN9074/hw1.0),\
|
|
$(error Unrecognized board-file suffix '$(suffix $(1))' for '$(1)')\
|
|
))))))))
|
|
|
|
endef
|
|
# Blank line required at end of above define due to foreach context
|
|
|
|
define generate-ipq-wifi-package
|
|
define Package/ipq-wifi-$(1)
|
|
$(call Package/ipq-wifi-default)
|
|
TITLE:=board-2.bin Overrides for $(2)
|
|
CONFLICTS:=$(PREV_BOARD)
|
|
endef
|
|
|
|
define Package/ipq-wifi-$(1)/description
|
|
The $(2) requires board-specific, reference ("cal") data
|
|
that is not yet present in the upstream wireless firmware distribution.
|
|
|
|
This package supplies board-2.bin file(s) that, in the interim,
|
|
overwrite those supplied by the ath10k-firmware-* packages.
|
|
|
|
This is package is only necessary for the $(2).
|
|
|
|
Do not install it for any other device!
|
|
endef
|
|
|
|
define Package/ipq-wifi-$(1)/install-overlay
|
|
$$$$(foreach IPQ_WIFI_BOARD_FILE,$$$$(wildcard $(PKG_BUILD_DIR)/board-$(1).*),\
|
|
$$$$(call ipq-wifi-install-one,$$$$(IPQ_WIFI_BOARD_FILE),$$(1)))
|
|
endef
|
|
|
|
PREV_BOARD+=ipq-wifi-$(1)
|
|
endef
|
|
|
|
# To add local files for testing:
|
|
# 1. create a new directory in the ipq-wifi package directory called "files".
|
|
# 2. place there the needed board files.
|
|
#
|
|
# To send a board file upstream:
|
|
# 1. create a pull request in https://github.com/openwrt/firmware_qca-wireless or
|
|
# send a patch to the mailing list adding the tag firmware/qca-wireless before
|
|
# the PATCH tag.
|
|
# 2. create a pull request in the main openwrt repository bumping the ipq-wifi
|
|
# package to the new version and adding the required lines to add the board file.
|
|
#
|
|
# Changes needed to the ipq-wifi Makefile:
|
|
# 1. Add board name to ALLWIFIBOARDS
|
|
# 2. Add $(eval $(call generate-ipq-wifi-package,<devicename>,<display name>))
|
|
#
|
|
# Board files should follow this name structure:
|
|
# board-<devicename>.<qca4019|qca9888|qca9889|qca9984|qca99x0|ipq8074>
|
|
|
|
$(eval $(call generate-ipq-wifi-package,8devices_mango,8devices Mango))
|
|
$(eval $(call generate-ipq-wifi-package,arcadyan_aw1000,Arcadyan AW1000))
|
|
$(eval $(call generate-ipq-wifi-package,buffalo_wxr-5950ax12,Buffalo WXR-5950AX12))
|
|
$(eval $(call generate-ipq-wifi-package,cmcc_rm2-6,CMCC RM2-6))
|
|
$(eval $(call generate-ipq-wifi-package,compex_wpq873,Compex WPQ-873))
|
|
$(eval $(call generate-ipq-wifi-package,dynalink_dl-wrx36,Dynalink DL-WRX36))
|
|
$(eval $(call generate-ipq-wifi-package,edgecore_eap102,Edgecore EAP102))
|
|
$(eval $(call generate-ipq-wifi-package,edimax_cax1800,Edimax CAX1800))
|
|
$(eval $(call generate-ipq-wifi-package,linksys_mx4200,Linksys MX4200))
|
|
$(eval $(call generate-ipq-wifi-package,linksys_mx5300,Linksys MX5300))
|
|
$(eval $(call generate-ipq-wifi-package,netgear_lbr20,Netgear LBR20))
|
|
$(eval $(call generate-ipq-wifi-package,netgear_rax120v2,Netgear RAX120v2))
|
|
$(eval $(call generate-ipq-wifi-package,netgear_wax214,Netgear WAX214))
|
|
$(eval $(call generate-ipq-wifi-package,netgear_wax218,Netgear WAX218))
|
|
$(eval $(call generate-ipq-wifi-package,netgear_wax620,Netgear WAX620))
|
|
$(eval $(call generate-ipq-wifi-package,netgear_wax630,Netgear WAX630))
|
|
$(eval $(call generate-ipq-wifi-package,qnap_301w,QNAP 301w))
|
|
$(eval $(call generate-ipq-wifi-package,prpl_haze,prpl Haze))
|
|
$(eval $(call generate-ipq-wifi-package,redmi_ax6,Redmi AX6))
|
|
$(eval $(call generate-ipq-wifi-package,wallys_dr40x9,Wallys DR40X9))
|
|
$(eval $(call generate-ipq-wifi-package,xiaomi_ax3600,Xiaomi AX3600))
|
|
$(eval $(call generate-ipq-wifi-package,xiaomi_ax9000,Xiaomi AX9000))
|
|
$(eval $(call generate-ipq-wifi-package,yyets_le1,YYeTs LE1))
|
|
$(eval $(call generate-ipq-wifi-package,yuncore_ax880,Yuncore AX880))
|
|
$(eval $(call generate-ipq-wifi-package,zte_mf269,ZTE MF269))
|
|
$(eval $(call generate-ipq-wifi-package,zte_mf289f,ZTE MF289F))
|
|
$(eval $(call generate-ipq-wifi-package,zte_mf287,ZTE MF287))
|
|
$(eval $(call generate-ipq-wifi-package,zte_mf287plus,ZTE MF287Plus))
|
|
$(eval $(call generate-ipq-wifi-package,zyxel_nbg7815,Zyxel NBG7815))
|
|
|
|
$(foreach PACKAGE,$(ALLWIFIPACKAGES),$(eval $(call BuildPackage,$(PACKAGE))))
|