ExternalVendorCode/openwrt
1
0
Fork 0
mirror of https://github.com/openwrt/openwrt.git synced 2025-01-04 21:14:21 +00:00
Code Issues Actions 7 Packages Projects Releases Wiki Activity
31a6605de0
openwrt/target/linux/ath79/image/generic.mk
Michael Pratt 5df1b33298 ath79: add support for Senao Watchguard AP100 
FCC ID: U2M-CAP2100AG

WatchGuard AP100 is an indoor wireless access point with
1 Gb ethernet port, dual-band but single-radio wireless,
internal antenna plates, and 802.3at PoE+

this board is a Senao device:
the hardware is equivalent to EnGenius EAP300 v2
the software is modified Senao SDK which is based on openwrt and uboot
including image checksum verification at boot time,
and a failsafe image that boots if checksum fails

**Specification:**

  - AR9344 SOC          MIPS 74kc, 2.4 GHz AND 5 GHz WMAC, 2x2
  - AR8035-A EPHY       RGMII GbE with PoE+ IN
  - 25 MHz clock
  - 16 MB FLASH         mx25l12805d
  - 2x 64 MB RAM
  - UART console        J11, populated
  - GPIO watchdog       GPIO 16, 20 sec toggle
  - 2 antennas          5 dBi, internal omni-directional plates
  - 5 LEDs              power, eth0 link/data, 2G, 5G
  - 1 button            reset

**MAC addresses:**

  Label has no MAC
  Only one Vendor MAC address in flash at art 0x0

  eth0 ---- *:e5 art 0x0 -2
  phy0 ---- *:e5 art 0x0 -2

**Installation:**

  Method 1: OEM webpage

    use OEM webpage for firmware upgrade to upload factory.bin

  Method 2: root shell

    It may be necessary to use a Watchguard router to flash the image to the AP
    and / or to downgrade the software on the AP to access SSH
    For some Watchguard devices, serial console over UART is disabled.

  NOTE: DHCP is not enabled by default after flashing

**TFTP recovery:**

  reset button has no function at boot time
  only possible with modified uboot environment,
  (see commit message for Watchguard AP300)

**Return to OEM:**

  user should make backup of MTD partitions
  and write the backups back to mtd devices
  in order to revert to OEM reliably

  It may be possible to use sysupgrade
  with an OEM image as well...
  (not tested)

**OEM upgrade info:**

  The OEM upgrade script is at /etc/fwupgrade.sh

  OKLI kernel loader is required because the OEM software
  expects the kernel to be no greater than 1536k
  and the factory.bin upgrade procedure would otherwise
  overwrite part of the kernel when writing rootfs.

**Note on eth0 PLL-data:**

  The default Ethernet Configuration register values will not work
  because of the external AR8035 switch between
  the SOC and the ethernet port.

  For AR934x series, the PLL registers for eth0
  can be see in the DTSI as 0x2c.
  Therefore the PLL registers can be read from uboot
  for each link speed after attempting tftpboot
  or another network action using that link speed
  with `md 0x1805002c 1`.

  The clock delay required for RGMII can be applied
  at the PHY side, using the at803x driver `phy-mode`.
  Therefore the PLL registers for GMAC0
  do not need the bits for delay on the MAC side.
  This is possible due to fixes in at803x driver
  since Linux 5.1 and 5.3

**Note on WatchGuard Magic string:**

  The OEM upgrade script is a modified version of
  the generic Senao sysupgrade script
  which is used on EnGenius devices.

  On WatchGuard boards produced by Senao,
  images are verified using a md5sum checksum of
  the upgrade image concatenated with a magic string.
  this checksum is then appended to the end of the final image.

  This variable does not apply to all the senao devices
  so set to null string as default

Tested-by: Steve Wheeler <stephenw10@gmail.com>
Signed-off-by: Michael Pratt <mcpratt@pm.me>
2022-09-11 21:54:00 +02:00

2837 lines
78 KiB
Makefile
Raw Blame History

include ./common-buffalo.mk
include ./common-netgear.mk
include ./common-senao.mk
include ./common-tp-link.mk
include ./common-yuncore.mk
include ./common-ubnt.mk
DEVICE_VARS += ADDPATTERN_ID ADDPATTERN_VERSION
DEVICE_VARS += SEAMA_SIGNATURE SEAMA_MTDBLOCK
DEVICE_VARS += KERNEL_INITRAMFS_PREFIX DAP_SIGNATURE
DEVICE_VARS += EDIMAX_HEADER_MAGIC EDIMAX_HEADER_MODEL
DEVICE_VARS += OPENMESH_CE_TYPE ZYXEL_MODEL_STRING
define Build/add-elecom-factory-initramfs
$(eval edimax_model=$(word 1,$(1)))
$(eval product=$(word 2,$(1)))
$(STAGING_DIR_HOST)/bin/mkedimaximg \
-b -s CSYS -m $(edimax_model) \
-f 0x70000 -S 0x01100000 \
-i $@ -o $@.factory
$(call Build/elecom-product-header,$(product) $@.factory)
if [ "$$(stat -c%s $@.factory)" -le $$(($(subst k,* 1024,$(subst m, * 1024k,$(IMAGE_SIZE))))) ]; then \
mv $@.factory $(BIN_DIR)/$(KERNEL_INITRAMFS_PREFIX)-factory.bin; \
else \
echo "WARNING: initramfs kernel image too big, cannot generate factory image" >&2; \
fi
endef
define Build/addpattern
-$(STAGING_DIR_HOST)/bin/addpattern -B $(ADDPATTERN_ID) \
-v v$(ADDPATTERN_VERSION) -i $@ -o $@.new
-mv "$@.new" "$@"
endef
define Build/append-md5sum-bin
$(MKHASH) md5 $@ | sed 's/../\\\\x&/g' |\
xargs echo -ne >> $@
endef
define Build/cybertan-trx
@echo -n '' > $@-empty.bin
-$(STAGING_DIR_HOST)/bin/trx -o $@.new \
-f $(IMAGE_KERNEL) -F $@-empty.bin \
-x 32 -a 0x10000 -x -32 -f $@
-mv "$@.new" "$@"
-rm $@-empty.bin
endef
define Build/edimax-headers
$(eval edimax_magic=$(word 1,$(1)))
$(eval edimax_model=$(word 2,$(1)))
$(STAGING_DIR_HOST)/bin/edimax_fw_header -M $(edimax_magic) -m $(edimax_model)\
-v $(VERSION_DIST)$(firstword $(subst +, , $(firstword $(subst -, ,$(REVISION))))) \
-n "uImage" \
-i $(KDIR)/loader-$(DEVICE_NAME).uImage \
-o $@.uImage
$(STAGING_DIR_HOST)/bin/edimax_fw_header -M $(edimax_magic) -m $(edimax_model)\
-v $(VERSION_DIST)$(firstword $(subst +, , $(firstword $(subst -, ,$(REVISION))))) \
-n "rootfs" \
-i $@ \
-o $@.rootfs
cat $@.uImage $@.rootfs > $@
rm -rf $@.uImage $@.rootfs
endef
define Build/mkdapimg2
$(STAGING_DIR_HOST)/bin/mkdapimg2 \
-i $@ -o $@.new \
-s $(DAP_SIGNATURE) \
-v $(VERSION_DIST)-$(firstword $(subst +, , \
$(firstword $(subst -, ,$(REVISION))))) \
-r Default \
$(if $(1),-k $(1))
mv $@.new $@
endef
define Build/mkmylofw_16m
$(eval device_id=$(word 1,$(1)))
$(eval revision=$(word 2,$(1)))
# On WPJ344, WPJ531, and WPJ563, the default boot command tries 0x9f680000
# first and fails if the remains of the stock image are sill there
# - resulting in an infinite boot loop.
# The size parameter is grown to have that block deleted if the firmware
# isn't big enough by itself.
let \
size="$$(stat -c%s $@)" \
pad="$(subst k,* 1024,$(BLOCKSIZE))" \
pad="(pad - (size % pad)) % pad" \
newsize='size + pad' ; \
[ $$newsize -lt $$((0x660000)) ] && newsize=0x660000 ; \
$(STAGING_DIR_HOST)/bin/mkmylofw \
-B WPE72 -i 0x11f6:$(device_id):0x11f6:$(device_id) -r $(revision) \
-s 0x1000000 -p0x30000:$$newsize:al:0x80060000:"OpenWRT":$@ \
$@.new
@mv $@.new $@
endef
define Build/mkwrggimg
$(STAGING_DIR_HOST)/bin/mkwrggimg -b \
-i $@ -o $@.imghdr -d /dev/mtdblock/1 \
-m $(DEVICE_MODEL)-$(DEVICE_VARIANT) -s $(DAP_SIGNATURE) \
-v $(VERSION_DIST) -B $(REVISION)
mv $@.imghdr $@
endef
define Build/nec-enc
$(STAGING_DIR_HOST)/bin/nec-enc \
-i $@ -o $@.new -k $(1)
mv $@.new $@
endef
define Build/nec-fw
( stat -c%s $@ | tr -d "\n" | dd bs=16 count=1 conv=sync; ) >> $@
( \
echo -n -e "$(1)" | dd bs=16 count=1 conv=sync; \
echo -n "0.0.00" | dd bs=16 count=1 conv=sync; \
dd if=$@; \
) > $@.new
mv $@.new $@
endef
define Build/pisen_wmb001n-factory
-[ -f "$@" ] && \
mkdir -p "$@.tmp" && \
cp "$(KDIR)/loader-$(word 1,$(1)).uImage" "$@.tmp/uImage" && \
mv "$@" "$@.tmp/rootfs" && \
cp "bin/pisen_wmb001n_factory-header.bin" "$@" && \
$(TAR) -cp --numeric-owner --owner=0 --group=0 --mode=a-s --sort=name \
$(if $(SOURCE_DATE_EPOCH),--mtime="@$(SOURCE_DATE_EPOCH)") \
-C "$@.tmp" . | gzip -9n >> "$@" && \
rm -rf "$@.tmp"
endef
define Build/teltonika-fw-fake-checksum
# Teltonika U-Boot web based firmware upgrade/recovery routine compares
# 16 bytes from md5sum1[16] field in TP-Link v1 header (offset: 76 bytes
# from begin of the firmware file) with 16 bytes stored just before
# 0xdeadc0de marker. Values are only compared, MD5 sum is not verified.
let \
offs="$$(stat -c%s $@) - $(1)"; \
dd if=$@ bs=1 count=16 skip=76 |\
dd of=$@ bs=1 count=16 seek=$$offs conv=notrunc
endef
define Build/teltonika-v1-header
$(STAGING_DIR_HOST)/bin/mktplinkfw \
-c -H $(TPLINK_HWID) -W $(TPLINK_HWREV) -L $(KERNEL_LOADADDR) \
-E $(if $(KERNEL_ENTRY),$(KERNEL_ENTRY),$(KERNEL_LOADADDR)) \
-m $(TPLINK_HEADER_VERSION) -N "$(VERSION_DIST)" -V "RUT2xx " \
-k $@ -o $@.new $(1)
@mv $@.new $@
endef
define Build/wrgg-pad-rootfs
$(STAGING_DIR_HOST)/bin/padjffs2 $(IMAGE_ROOTFS) -c 64 >>$@
endef
define Build/zyxel-tar-bz2
mkdir -p $@.tmp
mv $@ $@.tmp/$(word 2,$(1))
cp $(KDIR)/loader-$(DEVICE_NAME).uImage $@.tmp/$(word 1,$(1)).lzma.uImage
$(TAR) -cjf $@ -C $@.tmp .
rm -rf $@.tmp
endef
define Device/seama
KERNEL := kernel-bin | append-dtb | relocate-kernel | lzma
KERNEL_INITRAMFS := $$(KERNEL) | seama
IMAGES += factory.bin
SEAMA_MTDBLOCK := 1
# 64 bytes offset:
# - 28 bytes seama_header
# - 36 bytes of META data (4-bytes aligned)
IMAGE/default := append-kernel | pad-offset $$$$(BLOCKSIZE) 64 | append-rootfs
IMAGE/sysupgrade.bin := $$(IMAGE/default) | seama | pad-rootfs | \
check-size | append-metadata
IMAGE/factory.bin := $$(IMAGE/default) | pad-rootfs -x 64 | seama | \
seama-seal | check-size
SEAMA_SIGNATURE :=
endef
define Device/8dev_carambola2
SOC := ar9331
DEVICE_VENDOR := 8devices
DEVICE_MODEL := Carambola2
DEVICE_PACKAGES := kmod-usb-chipidea2
IMAGE_SIZE := 16000k
SUPPORTED_DEVICES += carambola2
endef
TARGET_DEVICES += 8dev_carambola2
define Device/8dev_lima
SOC := qca9531
DEVICE_VENDOR := 8devices
DEVICE_MODEL := Lima
DEVICE_PACKAGES := kmod-usb2
IMAGE_SIZE := 15616k
SUPPORTED_DEVICES += lima
endef
TARGET_DEVICES += 8dev_lima
define Device/adtran_bsap1880
SOC := ar7161
DEVICE_VENDOR := Adtran/Bluesocket
DEVICE_PACKAGES += -swconfig -uboot-envtools fconfig
KERNEL := kernel-bin | append-dtb | lzma | pad-to $$(BLOCKSIZE)
KERNEL_INITRAMFS := kernel-bin | append-dtb
IMAGE_SIZE := 11200k
IMAGES += kernel.bin rootfs.bin
IMAGE/kernel.bin := append-kernel
IMAGE/rootfs.bin := append-rootfs | pad-rootfs | pad-to $$(BLOCKSIZE)
IMAGE/sysupgrade.bin := append-rootfs | pad-rootfs | \
check-size | sysupgrade-tar rootfs=$$$$@ | append-metadata
endef
define Device/adtran_bsap1800-v2
$(Device/adtran_bsap1880)
DEVICE_MODEL := BSAP-1800
DEVICE_VARIANT := v2
endef
TARGET_DEVICES += adtran_bsap1800-v2
define Device/adtran_bsap1840
$(Device/adtran_bsap1880)
DEVICE_MODEL := BSAP-1840
endef
TARGET_DEVICES += adtran_bsap1840
define Device/airtight_c-75
SOC := qca9550
DEVICE_VENDOR := AirTight Networks
DEVICE_MODEL := C-75
DEVICE_ALT0_VENDOR := Mojo Networks
DEVICE_ALT0_MODEL := C-75
DEVICE_ALT1_VENDOR := WatchGuard
DEVICE_ALT1_MODEL := AP320
DEVICE_PACKAGES := ath10k-firmware-qca988x-ct kmod-ath10k-ct kmod-usb2
IMAGE_SIZE := 32320k
KERNEL_SIZE := 15936k
endef
TARGET_DEVICES += airtight_c-75
define Device/alfa-network_ap121f
SOC := ar9331
DEVICE_VENDOR := ALFA Network
DEVICE_MODEL := AP121F
DEVICE_PACKAGES := kmod-usb-chipidea2 kmod-usb-storage -swconfig
IMAGE_SIZE := 16064k
SUPPORTED_DEVICES += ap121f
endef
TARGET_DEVICES += alfa-network_ap121f
define Device/alfa-network_ap121fe
SOC := ar9331
DEVICE_VENDOR := ALFA Network
DEVICE_MODEL := AP121FE
DEVICE_PACKAGES := kmod-usb-chipidea2 kmod-usb-gadget-eth -swconfig
IMAGE_SIZE := 16064k
endef
TARGET_DEVICES += alfa-network_ap121fe
define Device/alfa-network_n2q
SOC := qca9531
DEVICE_VENDOR := ALFA Network
DEVICE_MODEL := N2Q
DEVICE_PACKAGES := kmod-i2c-gpio kmod-gpio-pcf857x kmod-usb2 \
kmod-usb-ledtrig-usbport rssileds
IMAGE_SIZE := 15872k
endef
TARGET_DEVICES += alfa-network_n2q
define Device/alfa-network_n5q
SOC := ar9344
DEVICE_VENDOR := ALFA Network
DEVICE_MODEL := N5Q
DEVICE_PACKAGES := rssileds
IMAGE_SIZE := 15872k
SUPPORTED_DEVICES += n5q
endef
TARGET_DEVICES += alfa-network_n5q
define Device/alfa-network_pi-wifi4
SOC := qca9531
DEVICE_VENDOR := ALFA Network
DEVICE_MODEL := Pi-WiFi4
DEVICE_PACKAGES := kmod-usb2 kmod-usb-ledtrig-usbport -swconfig
IMAGE_SIZE := 15872k
endef
TARGET_DEVICES += alfa-network_pi-wifi4
define Device/alfa-network_r36a
SOC := qca9531
DEVICE_VENDOR := ALFA Network
DEVICE_MODEL := R36A
DEVICE_PACKAGES := kmod-usb2 kmod-usb-ledtrig-usbport
IMAGE_SIZE := 15872k
SUPPORTED_DEVICES += r36a
endef
TARGET_DEVICES += alfa-network_r36a
define Device/alfa-network_tube-2hq
SOC := qca9531
DEVICE_VENDOR := ALFA Network
DEVICE_MODEL := Tube-2HQ
DEVICE_PACKAGES := rssileds -swconfig
IMAGE_SIZE := 15872k
SUPPORTED_DEVICES += tube-2hq
endef
TARGET_DEVICES += alfa-network_tube-2hq
define Device/allnet_all-wap02860ac
$(Device/senao_loader_okli)
SOC := qca9558
DEVICE_VENDOR := ALLNET
DEVICE_MODEL := ALL-WAP02860AC
DEVICE_PACKAGES := ath10k-firmware-qca988x-ct kmod-ath10k-ct
IMAGE_SIZE := 11584k
LOADER_FLASH_OFFS := 0x220000
SENAO_IMGNAME := senao-allwap02860ac
endef
TARGET_DEVICES += allnet_all-wap02860ac
define Device/araknis_an-300-ap-i-n
$(Device/senao_loader_okli)
SOC := ar9344
DEVICE_VENDOR := Araknis
DEVICE_MODEL := AN-300-AP-I-N
IMAGE_SIZE := 12096k
LOADER_FLASH_OFFS := 0x220000
SENAO_IMGNAME := senao-an300
endef
TARGET_DEVICES += araknis_an-300-ap-i-n
define Device/araknis_an-500-ap-i-ac
$(Device/senao_loader_okli)
SOC := qca9557
DEVICE_VENDOR := Araknis
DEVICE_MODEL := AN-500-AP-I-AC
DEVICE_PACKAGES := ath10k-firmware-qca988x-ct kmod-ath10k-ct
IMAGE_SIZE := 11584k
LOADER_FLASH_OFFS := 0x220000
SENAO_IMGNAME := senao-generic-v1-an500
endef
TARGET_DEVICES += araknis_an-500-ap-i-ac
define Device/araknis_an-700-ap-i-ac
$(Device/senao_loader_okli)
SOC := qca9558
DEVICE_VENDOR := Araknis
DEVICE_MODEL := AN-700-AP-I-AC
DEVICE_PACKAGES := ath10k-firmware-qca988x-ct kmod-ath10k-ct
IMAGE_SIZE := 11584k
LOADER_FLASH_OFFS := 0x220000
SENAO_IMGNAME := senao-generic-v1-an700
endef
TARGET_DEVICES += araknis_an-700-ap-i-ac
define Device/arduino_yun
SOC := ar9331
DEVICE_VENDOR := Arduino
DEVICE_MODEL := Yun
DEVICE_PACKAGES := kmod-usb-chipidea2 kmod-usb-ledtrig-usbport \
kmod-usb-storage block-mount -swconfig
IMAGE_SIZE := 15936k
SUPPORTED_DEVICES += arduino-yun
endef
TARGET_DEVICES += arduino_yun
define Device/aruba_ap-105
SOC := ar7161
DEVICE_VENDOR := Aruba
DEVICE_MODEL := AP-105
IMAGE_SIZE := 16000k
DEVICE_PACKAGES := kmod-i2c-gpio kmod-tpm-i2c-atmel
endef
TARGET_DEVICES += aruba_ap-105
define Device/asus_pl-ac56
SOC := qca9563
DEVICE_VENDOR := ASUS
DEVICE_MODEL := PL-AC56
DEVICE_VARIANT := A1
IMAGE_SIZE := 15488k
IMAGES += factory.bin
IMAGE/factory.bin := append-kernel | pad-to $$$$(BLOCKSIZE) | \
append-rootfs | pad-rootfs
DEVICE_PACKAGES := kmod-ath10k-ct-smallbuffers ath10k-firmware-qca988x-ct
endef
TARGET_DEVICES += asus_pl-ac56
define Device/asus_rp-ac51
SOC := qca9531
DEVICE_VENDOR := ASUS
DEVICE_MODEL := RP-AC51
IMAGE_SIZE := 16000k
IMAGES += factory.bin
DEVICE_PACKAGES := kmod-ath10k-ct ath10k-firmware-qca9888-ct \
-swconfig
endef
TARGET_DEVICES += asus_rp-ac51
define Device/asus_rp-ac66
SOC := qca9563
DEVICE_VENDOR := ASUS
DEVICE_MODEL := RP-AC66
IMAGE_SIZE := 16000k
IMAGES += factory.bin
IMAGE/factory.bin := append-kernel | pad-to $$$$(BLOCKSIZE) | \
append-rootfs | pad-rootfs
DEVICE_PACKAGES := kmod-ath10k-ct-smallbuffers ath10k-firmware-qca988x-ct \
rssileds -swconfig
endef
TARGET_DEVICES += asus_rp-ac66
define Device/atheros_db120
$(Device/loader-okli-uimage)
SOC := ar9344
DEVICE_VENDOR := Atheros
DEVICE_MODEL := DB120
DEVICE_PACKAGES := kmod-usb2
IMAGE_SIZE := 7808k
SUPPORTED_DEVICES += db120
LOADER_FLASH_OFFS := 0x50000
KERNEL := kernel-bin | append-dtb | lzma | uImage lzma -M 0x4f4b4c49
IMAGES += factory.bin
IMAGE/factory.bin := append-kernel | pad-to $$$$(BLOCKSIZE) | \
append-rootfs | pad-rootfs | check-size | pad-to 6336k | \
append-loader-okli-uimage $(1) | pad-to 64k
endef
TARGET_DEVICES += atheros_db120
define Device/avm
DEVICE_VENDOR := AVM
KERNEL := kernel-bin | append-dtb | lzma | eva-image
KERNEL_INITRAMFS := $$(KERNEL)
IMAGE/sysupgrade.bin := append-kernel | pad-to 64k | \
append-squashfs-fakeroot-be | pad-to 256 | append-rootfs | pad-rootfs | \
check-size | append-metadata
DEVICE_PACKAGES := fritz-tffs
endef
define Device/avm_fritz1750e
$(Device/avm)
SOC := qca9556
IMAGE_SIZE := 15232k
DEVICE_MODEL := FRITZ!WLAN Repeater 1750E
DEVICE_PACKAGES += rssileds kmod-ath10k-ct-smallbuffers \
ath10k-firmware-qca988x-ct -swconfig
endef
TARGET_DEVICES += avm_fritz1750e
define Device/avm_fritz300e
$(Device/avm)
SOC := ar7242
IMAGE_SIZE := 15232k
DEVICE_MODEL := FRITZ!WLAN Repeater 300E
DEVICE_PACKAGES += rssileds -swconfig
SUPPORTED_DEVICES += fritz300e
endef
TARGET_DEVICES += avm_fritz300e
define Device/avm_fritz4020
$(Device/avm)
SOC := qca9561
IMAGE_SIZE := 15232k
DEVICE_MODEL := FRITZ!Box 4020
SUPPORTED_DEVICES += fritz4020
endef
TARGET_DEVICES += avm_fritz4020
define Device/avm_fritz450e
$(Device/avm)
SOC := qca9556
IMAGE_SIZE := 15232k
DEVICE_MODEL := FRITZ!WLAN Repeater 450E
SUPPORTED_DEVICES += fritz450e
endef
TARGET_DEVICES += avm_fritz450e
define Device/avm_fritzdvbc
$(Device/avm)
SOC := qca9556
IMAGE_SIZE := 15232k
DEVICE_MODEL := FRITZ!WLAN Repeater DVB-C
DEVICE_PACKAGES += rssileds kmod-ath10k-ct-smallbuffers \
ath10k-firmware-qca988x-ct -swconfig
endef
TARGET_DEVICES += avm_fritzdvbc
define Device/belkin_f9x-v2
$(Device/loader-okli-uimage)
SOC := qca9558
DEVICE_VENDOR := Belkin
IMAGE_SIZE := 14464k
DEVICE_PACKAGES += kmod-ath10k-ct ath10k-firmware-qca988x-ct kmod-usb2 \
kmod-usb3 kmod-usb-ledtrig-usbport
LOADER_FLASH_OFFS := 0x50000
KERNEL := kernel-bin | append-dtb | lzma | uImage lzma -M 0x4f4b4c49
IMAGES += factory.bin
IMAGE/factory.bin := append-kernel | pad-to $$$$(BLOCKSIZE) | \
append-rootfs | pad-rootfs | check-size | \
edimax-headers $$$$(EDIMAX_HEADER_MAGIC) $$$$(EDIMAX_HEADER_MODEL) | \
pad-to $$$$(BLOCKSIZE)
endef
define Device/belkin_f9j1108-v2
$(Device/belkin_f9x-v2)
DEVICE_MODEL := F9J1108 v2 (AC1750 DB Wi-Fi)
EDIMAX_HEADER_MAGIC := F9J1108v1
EDIMAX_HEADER_MODEL := BR-6679BAC
endef
TARGET_DEVICES += belkin_f9j1108-v2
define Device/belkin_f9k1115-v2
$(Device/belkin_f9x-v2)
DEVICE_MODEL := F9K1115 v2 (AC1750 DB Wi-Fi)
EDIMAX_HEADER_MAGIC := eDiMaX
EDIMAX_HEADER_MODEL := F9K1115V2
endef
TARGET_DEVICES += belkin_f9k1115-v2
define Device/buffalo_bhr-4grv
$(Device/buffalo_common)
SOC := ar7242
DEVICE_MODEL := BHR-4GRV
BUFFALO_PRODUCT := BHR-4GRV
DEVICE_PACKAGES := kmod-usb2 kmod-usb-ledtrig-usbport
IMAGE_SIZE := 32256k
SUPPORTED_DEVICES += wzr-hp-g450h
endef
TARGET_DEVICES += buffalo_bhr-4grv
define Device/buffalo_bhr-4grv2
SOC := qca9557
DEVICE_VENDOR := Buffalo
DEVICE_MODEL := BHR-4GRV2
IMAGE_SIZE := 16000k
endef
TARGET_DEVICES += buffalo_bhr-4grv2
define Device/buffalo_wzr_ar7161
$(Device/buffalo_common)
SOC := ar7161
BUFFALO_PRODUCT := WZR-HP-AG300H
DEVICE_PACKAGES := kmod-usb-ohci kmod-usb2 kmod-usb-ledtrig-usbport \
kmod-leds-reset kmod-owl-loader
IMAGE_SIZE := 32320k
SUPPORTED_DEVICES += wzr-hp-ag300h
endef
define Device/buffalo_wzr-600dhp
$(Device/buffalo_wzr_ar7161)
DEVICE_MODEL := WZR-600DHP
endef
TARGET_DEVICES += buffalo_wzr-600dhp
define Device/buffalo_wzr-hp-ag300h
$(Device/buffalo_wzr_ar7161)
DEVICE_MODEL := WZR-HP-AG300H
endef
TARGET_DEVICES += buffalo_wzr-hp-ag300h
define Device/buffalo_wzr-hp-g300nh
$(Device/buffalo_common)
SOC := ar9132
BUFFALO_PRODUCT := WZR-HP-G300NH
BUFFALO_HWVER := 1
DEVICE_PACKAGES := kmod-gpio-cascade kmod-mux-gpio kmod-usb2 kmod-usb-ledtrig-usbport
BLOCKSIZE := 128k
IMAGE_SIZE := 32128k
SUPPORTED_DEVICES += wzr-hp-g300nh
endef
define Device/buffalo_wzr-hp-g300nh-rb
$(Device/buffalo_wzr-hp-g300nh)
DEVICE_MODEL := WZR-HP-G300NH (RTL8366RB switch)
endef
TARGET_DEVICES += buffalo_wzr-hp-g300nh-rb
define Device/buffalo_wzr-hp-g300nh-s
$(Device/buffalo_wzr-hp-g300nh)
DEVICE_MODEL := WZR-HP-G300NH (RTL8366S switch)
DEVICE_PACKAGES += kmod-switch-rtl8366rb
endef
TARGET_DEVICES += buffalo_wzr-hp-g300nh-s
define Device/buffalo_wzr-hp-g302h-a1a0
$(Device/buffalo_common)
SOC := ar7242
DEVICE_MODEL := WZR-HP-G302H
DEVICE_VARIANT := A1A0
BUFFALO_PRODUCT := WZR-HP-G302H
BUFFALO_HWVER := 4
DEVICE_PACKAGES := kmod-usb2 kmod-usb-ledtrig-usbport
IMAGE_SIZE := 32128k
SUPPORTED_DEVICES += wzr-hp-g300nh2
endef
TARGET_DEVICES += buffalo_wzr-hp-g302h-a1a0
define Device/buffalo_wzr-hp-g450h
$(Device/buffalo_common)
SOC := ar7242
DEVICE_MODEL := WZR-HP-G450H/WZR-450HP
BUFFALO_PRODUCT := WZR-HP-G450H
DEVICE_PACKAGES := kmod-usb2 kmod-usb-ledtrig-usbport
IMAGE_SIZE := 32256k
SUPPORTED_DEVICES += wzr-hp-g450h
endef
TARGET_DEVICES += buffalo_wzr-hp-g450h
define Device/comfast_cf-e110n-v2
SOC := qca9533
DEVICE_VENDOR := COMFAST
DEVICE_MODEL := CF-E110N
DEVICE_VARIANT := v2
DEVICE_PACKAGES := rssileds -swconfig -uboot-envtools
IMAGE_SIZE := 16192k
endef
TARGET_DEVICES += comfast_cf-e110n-v2
define Device/comfast_cf-e120a-v3
SOC := ar9344
DEVICE_VENDOR := COMFAST
DEVICE_MODEL := CF-E120A
DEVICE_VARIANT := v3
DEVICE_PACKAGES := rssileds -uboot-envtools
IMAGE_SIZE := 8000k
endef
TARGET_DEVICES += comfast_cf-e120a-v3
define Device/comfast_cf-e130n-v2
SOC := qca9531
DEVICE_VENDOR := COMFAST
DEVICE_MODEL := CF-E130N
DEVICE_VARIANT := v2
DEVICE_PACKAGES := rssileds -swconfig -uboot-envtools
IMAGE_SIZE := 7936k
endef
TARGET_DEVICES += comfast_cf-e130n-v2
define Device/comfast_cf-e313ac
SOC := qca9531
DEVICE_VENDOR := COMFAST
DEVICE_MODEL := CF-E313AC
DEVICE_PACKAGES := rssileds kmod-ath10k-ct-smallbuffers \
ath10k-firmware-qca9888-ct -swconfig -uboot-envtools
IMAGE_SIZE := 7936k
endef
TARGET_DEVICES += comfast_cf-e313ac
define Device/comfast_cf-e314n-v2
SOC := qca9531
DEVICE_VENDOR := COMFAST
DEVICE_MODEL := CF-E314N
DEVICE_VARIANT := v2
DEVICE_PACKAGES := rssileds
IMAGE_SIZE := 7936k
endef
TARGET_DEVICES += comfast_cf-e314n-v2
define Device/comfast_cf-e375ac
SOC := qca9563
DEVICE_VENDOR := COMFAST
DEVICE_MODEL := CF-E375AC
DEVICE_PACKAGES := kmod-ath10k-ct \
ath10k-firmware-qca9888-ct -uboot-envtools
IMAGE_SIZE := 16000k
endef
TARGET_DEVICES += comfast_cf-e375ac
define Device/comfast_cf-e5
SOC := qca9531
DEVICE_VENDOR := COMFAST
DEVICE_MODEL := CF-E5/E7
DEVICE_PACKAGES := rssileds kmod-usb2 kmod-usb-net-qmi-wwan -swconfig \
-uboot-envtools
IMAGE_SIZE := 16192k
endef
TARGET_DEVICES += comfast_cf-e5
define Device/comfast_cf-e560ac
SOC := qca9531
DEVICE_VENDOR := COMFAST
DEVICE_MODEL := CF-E560AC
DEVICE_PACKAGES := kmod-usb2 kmod-ath10k-ct ath10k-firmware-qca9888-ct
IMAGE_SIZE := 16128k
endef
TARGET_DEVICES += comfast_cf-e560ac
define Device/comfast_cf-ew72
SOC := qca9531
DEVICE_VENDOR := COMFAST
DEVICE_MODEL := CF-EW72
DEVICE_PACKAGES := kmod-usb2 kmod-ath10k-ct ath10k-firmware-qca9888-ct \
-uboot-envtools -swconfig
IMAGE_SIZE := 16192k
endef
TARGET_DEVICES += comfast_cf-ew72
define Device/comfast_cf-wr650ac-v1
SOC := qca9558
DEVICE_VENDOR := COMFAST
DEVICE_MODEL := CF-WR650AC
DEVICE_VARIANT := v1
DEVICE_PACKAGES := kmod-ath10k-ct ath10k-firmware-qca988x-ct
IMAGE_SIZE := 16128k
endef
TARGET_DEVICES += comfast_cf-wr650ac-v1
define Device/comfast_cf-wr650ac-v2
SOC := qca9558
DEVICE_VENDOR := COMFAST
DEVICE_MODEL := CF-WR650AC
DEVICE_VARIANT := v2
DEVICE_PACKAGES := kmod-ath10k-ct ath10k-firmware-qca988x-ct
IMAGE_SIZE := 16000k
endef
TARGET_DEVICES += comfast_cf-wr650ac-v2
define Device/comfast_cf-wr752ac-v1
SOC := qca9531
DEVICE_VENDOR := COMFAST
DEVICE_MODEL := CF-WR752AC
DEVICE_VARIANT := v1
DEVICE_PACKAGES := kmod-usb2 kmod-ath10k-ct ath10k-firmware-qca9888-ct \
-uboot-envtools
IMAGE_SIZE := 16192k
endef
TARGET_DEVICES += comfast_cf-wr752ac-v1
define Device/compex_wpj344-16m
SOC := ar9344
DEVICE_PACKAGES := kmod-usb2
IMAGE_SIZE := 16128k
DEVICE_VENDOR := Compex
DEVICE_MODEL := WPJ344
DEVICE_VARIANT := 16M
SUPPORTED_DEVICES += wpj344
IMAGES += cpximg-6a08.bin
IMAGE/cpximg-6a08.bin := append-kernel | pad-to $$$$(BLOCKSIZE) | append-rootfs | pad-rootfs | mkmylofw_16m 0x690 3
endef
TARGET_DEVICES += compex_wpj344-16m
define Device/compex_wpj531-16m
SOC := qca9531
DEVICE_PACKAGES := kmod-usb2
IMAGE_SIZE := 16128k
DEVICE_VENDOR := Compex
DEVICE_MODEL := WPJ531
DEVICE_VARIANT := 16M
SUPPORTED_DEVICES += wpj531
IMAGES += cpximg-7a03.bin cpximg-7a04.bin cpximg-7a06.bin cpximg-7a07.bin
IMAGE/cpximg-7a03.bin := append-kernel | pad-to $$$$(BLOCKSIZE) | append-rootfs | pad-rootfs | mkmylofw_16m 0x68a 2
IMAGE/cpximg-7a04.bin := append-kernel | pad-to $$$$(BLOCKSIZE) | append-rootfs | pad-rootfs | mkmylofw_16m 0x693 3
IMAGE/cpximg-7a06.bin := append-kernel | pad-to $$$$(BLOCKSIZE) | append-rootfs | pad-rootfs | mkmylofw_16m 0x693 3
IMAGE/cpximg-7a07.bin := append-kernel | pad-to $$$$(BLOCKSIZE) | append-rootfs | pad-rootfs | mkmylofw_16m 0x693 3
endef
TARGET_DEVICES += compex_wpj531-16m
define Device/compex_wpj558-16m
SOC := qca9558
IMAGE_SIZE := 16128k
DEVICE_VENDOR := Compex
DEVICE_MODEL := WPJ558
DEVICE_VARIANT := 16M
SUPPORTED_DEVICES += wpj558
IMAGES += cpximg-6a07.bin
IMAGE/cpximg-6a07.bin := append-kernel | pad-to $$$$(BLOCKSIZE) | \
append-rootfs | pad-rootfs | mkmylofw_16m 0x691 3
DEVICE_PACKAGES := kmod-gpio-beeper
endef
TARGET_DEVICES += compex_wpj558-16m
define Device/compex_wpj563
SOC := qca9563
DEVICE_PACKAGES := kmod-usb2 kmod-usb3
IMAGE_SIZE := 16128k
DEVICE_VENDOR := Compex
DEVICE_MODEL := WPJ563
SUPPORTED_DEVICES += wpj563
IMAGES += cpximg-7a02.bin
IMAGE/cpximg-7a02.bin := append-kernel | pad-to $$$$(BLOCKSIZE) | append-rootfs | pad-rootfs | mkmylofw_16m 0x694 2
endef
TARGET_DEVICES += compex_wpj563
define Device/devolo_dlan-pro-1200plus-ac
SOC := ar9344
DEVICE_VENDOR := Devolo
DEVICE_MODEL := dLAN pro 1200+ WiFi ac
DEVICE_PACKAGES := kmod-ath10k-ct ath10k-firmware-qca988x-ct
IMAGE_SIZE := 15872k
endef
TARGET_DEVICES += devolo_dlan-pro-1200plus-ac
define Device/devolo_dvl1200e
SOC := qca9558
DEVICE_VENDOR := devolo
DEVICE_MODEL := WiFi pro 1200e
DEVICE_PACKAGES := kmod-ath10k-ct ath10k-firmware-qca988x-ct
IMAGE_SIZE := 15936k
endef
TARGET_DEVICES += devolo_dvl1200e
define Device/devolo_dvl1200i
SOC := qca9558
DEVICE_VENDOR := devolo
DEVICE_MODEL := WiFi pro 1200i
DEVICE_PACKAGES := kmod-ath10k-ct ath10k-firmware-qca988x-ct
IMAGE_SIZE := 15936k
endef
TARGET_DEVICES += devolo_dvl1200i
define Device/devolo_dvl1750c
SOC := qca9558
DEVICE_VENDOR := devolo
DEVICE_MODEL := WiFi pro 1750c
DEVICE_PACKAGES := kmod-ath10k-ct ath10k-firmware-qca988x-ct
IMAGE_SIZE := 15936k
endef
TARGET_DEVICES += devolo_dvl1750c
define Device/devolo_dvl1750e
SOC := qca9558
DEVICE_VENDOR := devolo
DEVICE_MODEL := WiFi pro 1750e
DEVICE_PACKAGES := kmod-usb2 kmod-ath10k-ct ath10k-firmware-qca988x-ct
IMAGE_SIZE := 15936k
endef
TARGET_DEVICES += devolo_dvl1750e
define Device/devolo_dvl1750i
SOC := qca9558
DEVICE_VENDOR := devolo
DEVICE_MODEL := WiFi pro 1750i
DEVICE_PACKAGES := kmod-ath10k-ct ath10k-firmware-qca988x-ct
IMAGE_SIZE := 15936k
endef
TARGET_DEVICES += devolo_dvl1750i
define Device/devolo_dvl1750x
SOC := qca9558
DEVICE_VENDOR := devolo
DEVICE_MODEL := WiFi pro 1750x
DEVICE_PACKAGES := kmod-ath10k-ct ath10k-firmware-qca988x-ct
IMAGE_SIZE := 15936k
endef
TARGET_DEVICES += devolo_dvl1750x
define Device/devolo_magic-2-wifi
SOC := ar9344
DEVICE_VENDOR := Devolo
DEVICE_MODEL := Magic 2 WiFi
DEVICE_PACKAGES := kmod-ath10k-ct ath10k-firmware-qca988x-ct
IMAGE_SIZE := 15872k
endef
TARGET_DEVICES += devolo_magic-2-wifi
define Device/dlink_dap-13xx
SOC := qca9533
DEVICE_VENDOR := D-Link
DEVICE_PACKAGES += rssileds
IMAGE_SIZE := 7936k
IMAGES += factory.bin
IMAGE/factory.bin := append-kernel | pad-to $$$$(BLOCKSIZE) | \
append-rootfs | pad-rootfs | check-size | mkdapimg2 0xE0000
endef
define Device/dlink_dap-1330-a1
$(Device/dlink_dap-13xx)
DEVICE_MODEL := DAP-1330
DEVICE_VARIANT := A1
DAP_SIGNATURE := HONEYBEE-FIRMWARE-DAP-1330
SUPPORTED_DEVICES += dap-1330-a1
endef
TARGET_DEVICES += dlink_dap-1330-a1
define Device/dlink_dap-1365-a1
$(Device/dlink_dap-13xx)
DEVICE_MODEL := DAP-1365
DEVICE_VARIANT := A1
DAP_SIGNATURE := HONEYBEE-FIRMWARE-DAP-1365
endef
TARGET_DEVICES += dlink_dap-1365-a1
define Device/dlink_dap-2xxx
IMAGES += factory.img
IMAGE/factory.img := append-kernel | pad-offset 6144k 160 | \
append-rootfs | wrgg-pad-rootfs | mkwrggimg | check-size
IMAGE/sysupgrade.bin := append-kernel | mkwrggimg | \
pad-to $$$$(BLOCKSIZE) | append-rootfs | wrgg-pad-rootfs | \
check-size | append-metadata
KERNEL := kernel-bin | append-dtb | relocate-kernel | lzma
KERNEL_INITRAMFS := $$(KERNEL) | mkwrggimg
endef
define Device/dlink_dap-2230-a1
$(Device/dlink_dap-2xxx)
SOC := qca9533
DEVICE_VENDOR := D-Link
DEVICE_MODEL := DAP-2230
DEVICE_VARIANT := A1
IMAGE_SIZE := 15232k
DAP_SIGNATURE := wapn31_dkbs_dap2230
endef
TARGET_DEVICES += dlink_dap-2230-a1
define Device/dlink_dap-2660-a1
$(Device/dlink_dap-2xxx)
SOC := qca9557
DEVICE_VENDOR := D-Link
DEVICE_MODEL := DAP-2660
DEVICE_VARIANT := A1
DEVICE_PACKAGES := ath10k-firmware-qca988x-ct kmod-ath10k-ct
IMAGE_SIZE := 15232k
DAP_SIGNATURE := wapac09_dkbs_dap2660
endef
TARGET_DEVICES += dlink_dap-2660-a1
define Device/dlink_dap-2680-a1
$(Device/dlink_dap-2xxx)
SOC := qca9558
DEVICE_VENDOR := D-Link
DEVICE_MODEL := DAP-2680
DEVICE_VARIANT := A1
DEVICE_PACKAGES := ath10k-firmware-qca9984-ct kmod-ath10k-ct
IMAGE_SIZE := 15232k
DAP_SIGNATURE := wapac36_dkbs_dap2680
endef
TARGET_DEVICES += dlink_dap-2680-a1
define Device/dlink_dap-2695-a1
$(Device/dlink_dap-2xxx)
SOC := qca9558
DEVICE_VENDOR := D-Link
DEVICE_MODEL := DAP-2695
DEVICE_VARIANT := A1
DEVICE_PACKAGES := ath10k-firmware-qca988x-ct kmod-ath10k-ct
IMAGE_SIZE := 15360k
DAP_SIGNATURE := wapac02_dkbs_dap2695
SUPPORTED_DEVICES += dap-2695-a1
endef
TARGET_DEVICES += dlink_dap-2695-a1
define Device/dlink_dap-3320-a1
$(Device/dlink_dap-2xxx)
SOC := qca9533
DEVICE_VENDOR := D-Link
DEVICE_MODEL := DAP-3320
DEVICE_VARIANT := A1
IMAGE_SIZE := 15296k
DAP_SIGNATURE := wapn29_dkbs_dap3320
endef
TARGET_DEVICES += dlink_dap-3320-a1
define Device/dlink_dap-3662-a1
$(Device/dlink_dap-2xxx)
SOC := qca9558
DEVICE_VENDOR := D-Link
DEVICE_MODEL := DAP-3662
DEVICE_VARIANT := A1
DEVICE_PACKAGES := ath10k-firmware-qca988x-ct kmod-ath10k-ct
IMAGE_SIZE := 15296k
DAP_SIGNATURE := wapac11_dkbs_dap3662
endef
TARGET_DEVICES += dlink_dap-3662-a1
define Device/dlink_dch-g020-a1
SOC := qca9531
DEVICE_VENDOR := D-Link
DEVICE_MODEL := DCH-G020
DEVICE_VARIANT := A1
DEVICE_PACKAGES := kmod-gpio-pca953x kmod-i2c-gpio kmod-usb2 kmod-usb-acm
IMAGES += factory.bin
IMAGE_SIZE := 14784k
IMAGE/factory.bin := append-kernel | pad-to $$$$(BLOCKSIZE) | \
append-rootfs | pad-rootfs | check-size | mkdapimg2 0x20000
DAP_SIGNATURE := HONEYBEE-FIRMWARE-DCH-G020
endef
TARGET_DEVICES += dlink_dch-g020-a1
define Device/dlink_dir-505
SOC := ar9330
DEVICE_VENDOR := D-Link
DEVICE_MODEL := DIR-505
IMAGE_SIZE := 7680k
DEVICE_PACKAGES := kmod-usb-chipidea2
SUPPORTED_DEVICES += dir-505-a1
endef
TARGET_DEVICES += dlink_dir-505
define Device/dlink_dir-825-b1
SOC := ar7161
DEVICE_VENDOR := D-Link
DEVICE_MODEL := DIR-825
DEVICE_VARIANT := B1
IMAGE_SIZE := 6208k
IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | \
check-size | append-metadata
DEVICE_PACKAGES := kmod-usb-ohci kmod-usb2 kmod-usb-ledtrig-usbport \
kmod-leds-reset kmod-owl-loader kmod-switch-rtl8366s
SUPPORTED_DEVICES += dir-825-b1
endef
TARGET_DEVICES += dlink_dir-825-b1
define Device/dlink_dir-825-c1
SOC := ar9344
DEVICE_VENDOR := D-Link
DEVICE_MODEL := DIR-825
DEVICE_VARIANT := C1
DEVICE_PACKAGES := kmod-usb2 kmod-usb-ledtrig-usbport kmod-leds-reset \
kmod-owl-loader
SUPPORTED_DEVICES += dir-825-c1
IMAGE_SIZE := 15936k
IMAGES := factory.bin sysupgrade.bin
IMAGE/default := append-kernel | pad-to $$$$(BLOCKSIZE) | append-rootfs | \
pad-rootfs
IMAGE/factory.bin := $$(IMAGE/default) | pad-offset $$$$(IMAGE_SIZE) 26 | \
append-string 00DB120AR9344-RT-101214-00 | check-size
IMAGE/sysupgrade.bin := $$(IMAGE/default) | check-size | append-metadata
endef
TARGET_DEVICES += dlink_dir-825-c1
define Device/dlink_dir-835-a1
SOC := ar9344
DEVICE_VENDOR := D-Link
DEVICE_MODEL := DIR-835
DEVICE_VARIANT := A1
DEVICE_PACKAGES := kmod-usb2 kmod-leds-reset kmod-owl-loader
SUPPORTED_DEVICES += dir-835-a1
IMAGE_SIZE := 15936k
IMAGES := factory.bin sysupgrade.bin
IMAGE/default := append-kernel | pad-to $$$$(BLOCKSIZE) | append-rootfs | \
pad-rootfs
IMAGE/factory.bin := $$(IMAGE/default) | pad-offset $$$$(IMAGE_SIZE) 26 | \
append-string 00DB120AR9344-RT-101214-00 | check-size
IMAGE/sysupgrade.bin := $$(IMAGE/default) | check-size | append-metadata
endef
TARGET_DEVICES += dlink_dir-835-a1
define Device/dlink_dir-842-c
SOC := qca9563
DEVICE_VENDOR := D-Link
DEVICE_MODEL := DIR-842
KERNEL := kernel-bin | append-dtb | relocate-kernel | lzma
KERNEL_INITRAMFS := $$(KERNEL) | seama
IMAGES += factory.bin
SEAMA_MTDBLOCK := 5
SEAMA_SIGNATURE := wrgac65_dlink.2015_dir842
# 64 bytes offset:
# - 28 bytes seama_header
# - 36 bytes of META data (4-bytes aligned)
IMAGE/default := append-kernel | uImage lzma | \
pad-offset $$$$(BLOCKSIZE) 64 | append-rootfs
IMAGE/sysupgrade.bin := $$(IMAGE/default) | seama | pad-rootfs | \
check-size | append-metadata
IMAGE/factory.bin := $$(IMAGE/default) | pad-rootfs -x 64 | seama | \
seama-seal | check-size
IMAGE_SIZE := 15680k
endef
define Device/dlink_dir-842-c1
$(Device/dlink_dir-842-c)
DEVICE_VARIANT := C1
DEVICE_PACKAGES := kmod-ath10k-ct ath10k-firmware-qca9888-ct
endef
TARGET_DEVICES += dlink_dir-842-c1
define Device/dlink_dir-842-c2
$(Device/dlink_dir-842-c)
DEVICE_VARIANT := C2
DEVICE_PACKAGES := kmod-usb2 kmod-ath10k-ct ath10k-firmware-qca9888-ct
endef
TARGET_DEVICES += dlink_dir-842-c2
define Device/dlink_dir-842-c3
$(Device/dlink_dir-842-c)
DEVICE_VARIANT := C3
DEVICE_PACKAGES := kmod-ath10k-ct ath10k-firmware-qca9888-ct
endef
TARGET_DEVICES += dlink_dir-842-c3
define Device/dlink_dir-859-a1
$(Device/seama)
SOC := qca9563
DEVICE_VENDOR := D-Link
DEVICE_MODEL := DIR-859
DEVICE_VARIANT := A1
IMAGE_SIZE := 15872k
DEVICE_PACKAGES := kmod-usb2 kmod-ath10k-ct-smallbuffers ath10k-firmware-qca988x-ct
SEAMA_SIGNATURE := wrgac37_dlink.2013gui_dir859
endef
TARGET_DEVICES += dlink_dir-859-a1
define Device/elecom_wrc-1750ghbk2-i
SOC := qca9563
DEVICE_VENDOR := ELECOM
DEVICE_MODEL := WRC-1750GHBK2-I/C
IMAGE_SIZE := 15808k
KERNEL_INITRAMFS := $$(KERNEL) | pad-to 2 | \
add-elecom-factory-initramfs RN68 WRC-1750GHBK2
DEVICE_PACKAGES := kmod-ath10k-ct ath10k-firmware-qca988x-ct
endef
TARGET_DEVICES += elecom_wrc-1750ghbk2-i
define Device/elecom_wrc-300ghbk2-i
SOC := qca9563
DEVICE_VENDOR := ELECOM
DEVICE_MODEL := WRC-300GHBK2-I
IMAGE_SIZE := 7616k
KERNEL_INITRAMFS := $$(KERNEL) | pad-to 2 | \
add-elecom-factory-initramfs RN51 WRC-300GHBK2-I
endef
TARGET_DEVICES += elecom_wrc-300ghbk2-i
define Device/embeddedwireless_balin
SOC := ar9344
DEVICE_VENDOR := Embedded Wireless
DEVICE_MODEL := Balin
DEVICE_PACKAGES := kmod-usb-chipidea2
IMAGE_SIZE := 16000k
endef
TARGET_DEVICES += embeddedwireless_balin
define Device/embeddedwireless_dorin
SOC := ar9331
DEVICE_VENDOR := Embedded Wireless
DEVICE_MODEL := Dorin
DEVICE_PACKAGES := kmod-usb-chipidea2
IMAGE_SIZE := 16000k
endef
TARGET_DEVICES += embeddedwireless_dorin
define Device/engenius_eap1200h
$(Device/senao_loader_okli)
SOC := qca9557
DEVICE_VENDOR := EnGenius
DEVICE_MODEL := EAP1200H
DEVICE_PACKAGES := ath10k-firmware-qca988x-ct kmod-ath10k-ct
IMAGE_SIZE := 11584k
LOADER_FLASH_OFFS := 0x220000
SENAO_IMGNAME := ar71xx-generic-eap1200h
endef
TARGET_DEVICES += engenius_eap1200h
define Device/engenius_eap300-v2
$(Device/senao_loader_okli)
SOC := ar9341
DEVICE_VENDOR := EnGenius
DEVICE_MODEL := EAP300
DEVICE_VARIANT := v2
IMAGE_SIZE := 12096k
LOADER_FLASH_OFFS := 0x220000
SENAO_IMGNAME := senao-eap300v2
endef
TARGET_DEVICES += engenius_eap300-v2
define Device/engenius_eap600
$(Device/senao_loader_okli)
SOC := ar9344
DEVICE_VENDOR := EnGenius
DEVICE_MODEL := EAP600
IMAGE_SIZE := 12096k
LOADER_FLASH_OFFS := 0x220000
SENAO_IMGNAME := senao-eap600
endef
TARGET_DEVICES += engenius_eap600
define Device/engenius_ecb1200
SOC := qca9557
DEVICE_VENDOR := EnGenius
DEVICE_MODEL := ECB1200
DEVICE_PACKAGES := ath10k-firmware-qca988x-ct kmod-ath10k-ct
IMAGE_SIZE := 15680k
IMAGES += factory.bin
IMAGE/factory.bin := append-kernel | pad-to $$$$(BLOCKSIZE) | \
append-rootfs | pad-rootfs | check-size | \
senao-header -r 0x101 -p 0x6e -t 2
endef
TARGET_DEVICES += engenius_ecb1200
define Device/engenius_ecb1750
SOC := qca9558
DEVICE_VENDOR := EnGenius
DEVICE_MODEL := ECB1750
DEVICE_PACKAGES := ath10k-firmware-qca988x-ct kmod-ath10k-ct
IMAGE_SIZE := 15680k
IMAGES += factory.bin
IMAGE/factory.bin := append-kernel | pad-to $$$$(BLOCKSIZE) | \
append-rootfs | pad-rootfs | check-size | \
senao-header -r 0x101 -p 0x6d -t 2
endef
TARGET_DEVICES += engenius_ecb1750
define Device/engenius_ecb600
$(Device/senao_loader_okli)
SOC := ar9344
DEVICE_VENDOR := EnGenius
DEVICE_MODEL := ECB600
IMAGE_SIZE := 12096k
LOADER_FLASH_OFFS := 0x220000
SENAO_IMGNAME := senao-ecb600
endef
TARGET_DEVICES += engenius_ecb600
define Device/engenius_ens202ext-v1
$(Device/senao_loader_okli)
SOC := ar9341
DEVICE_VENDOR := EnGenius
DEVICE_MODEL := ENS202EXT
DEVICE_VARIANT := v1
DEVICE_PACKAGES := rssileds
IMAGE_SIZE := 12096k
LOADER_FLASH_OFFS := 0x220000
SENAO_IMGNAME := senao-ens202ext
endef
TARGET_DEVICES += engenius_ens202ext-v1
define Device/engenius_enstationac-v1
$(Device/senao_loader_okli)
SOC := qca9557
DEVICE_VENDOR := EnGenius
DEVICE_MODEL := EnStationAC
DEVICE_VARIANT := v1
DEVICE_PACKAGES := ath10k-firmware-qca988x-ct kmod-ath10k-ct rssileds
IMAGE_SIZE := 11584k
LOADER_FLASH_OFFS := 0x220000
SENAO_IMGNAME := ar71xx-generic-enstationac
endef
TARGET_DEVICES += engenius_enstationac-v1
define Device/engenius_epg5000
SOC := qca9558
DEVICE_VENDOR := EnGenius
DEVICE_MODEL := EPG5000
DEVICE_PACKAGES := ath10k-firmware-qca988x-ct kmod-ath10k-ct kmod-usb2
IMAGE_SIZE := 14656k
IMAGES += factory.dlf
IMAGE/factory.dlf := append-kernel | pad-to $$$$(BLOCKSIZE) | \
append-rootfs | pad-rootfs | check-size | \
senao-header -r 0x101 -p 0x71 -t 2
SUPPORTED_DEVICES += epg5000
endef
TARGET_DEVICES += engenius_epg5000
define Device/engenius_ews511ap
SOC := qca9531
DEVICE_VENDOR := EnGenius
DEVICE_MODEL := EWS511AP
DEVICE_PACKAGES := kmod-ath10k-ct ath10k-firmware-qca9887-ct
IMAGE_SIZE := 16000k
endef
TARGET_DEVICES += engenius_ews511ap
define Device/enterasys_ws-ap3705i
SOC := ar9344
DEVICE_VENDOR := Enterasys
DEVICE_MODEL := WS-AP3705i
IMAGE_SIZE := 30528k
endef
TARGET_DEVICES += enterasys_ws-ap3705i
define Device/etactica_eg200
SOC := ar9331
DEVICE_VENDOR := eTactica
DEVICE_MODEL := EG200
DEVICE_PACKAGES := kmod-usb-chipidea2 kmod-ledtrig-oneshot \
kmod-usb-serial-ftdi kmod-usb-storage kmod-fs-ext4
IMAGE_SIZE := 16000k
SUPPORTED_DEVICES += rme-eg200
endef
TARGET_DEVICES += etactica_eg200
define Device/extreme-networks_ws-ap3805i
SOC := qca9557
BLOCKSIZE := 256k
DEVICE_VENDOR := Extreme Networks
DEVICE_MODEL := WS-AP3805i
DEVICE_PACKAGES := ath10k-firmware-qca988x-ct kmod-ath10k-ct
IMAGE_SIZE := 29440k
endef
TARGET_DEVICES += extreme-networks_ws-ap3805i
define Device/glinet_6408
$(Device/tplink-8mlzma)
SOC := ar9331
DEVICE_VENDOR := GL.iNet
DEVICE_MODEL := 6408
DEVICE_PACKAGES := kmod-usb-chipidea2
IMAGE_SIZE := 8000k
TPLINK_HWID := 0x08000001
IMAGES := sysupgrade.bin
SUPPORTED_DEVICES += gl-inet
endef
TARGET_DEVICES += glinet_6408
define Device/glinet_6416
$(Device/tplink-16mlzma)
SOC := ar9331
DEVICE_VENDOR := GL.iNet
DEVICE_MODEL := 6416
DEVICE_PACKAGES := kmod-usb-chipidea2
IMAGE_SIZE := 16192k
TPLINK_HWID := 0x08000001
IMAGES := sysupgrade.bin
SUPPORTED_DEVICES += gl-inet
endef
TARGET_DEVICES += glinet_6416
define Device/glinet_gl-ar150
SOC := ar9330
DEVICE_VENDOR := GL.iNet
DEVICE_MODEL := GL-AR150
DEVICE_PACKAGES := kmod-usb-chipidea2
IMAGE_SIZE := 16000k
SUPPORTED_DEVICES += gl-ar150
endef
TARGET_DEVICES += glinet_gl-ar150
define Device/glinet_gl-ar300m-common-nor
SOC := qca9531
DEVICE_VENDOR := GL.iNet
DEVICE_PACKAGES := kmod-usb2
IMAGE_SIZE := 16000k
SUPPORTED_DEVICES += gl-ar300m
endef
define Device/glinet_gl-ar300m-lite
$(Device/glinet_gl-ar300m-common-nor)
DEVICE_MODEL := GL-AR300M
DEVICE_VARIANT := Lite
endef
TARGET_DEVICES += glinet_gl-ar300m-lite
define Device/glinet_gl-ar300m16
$(Device/glinet_gl-ar300m-common-nor)
DEVICE_MODEL := GL-AR300M16
endef
TARGET_DEVICES += glinet_gl-ar300m16
define Device/glinet_gl-ar750
SOC := qca9531
DEVICE_VENDOR := GL.iNet
DEVICE_MODEL := GL-AR750
DEVICE_PACKAGES := kmod-usb2 kmod-ath10k-ct ath10k-firmware-qca9887-ct
IMAGE_SIZE := 16000k
SUPPORTED_DEVICES += gl-ar750
endef
TARGET_DEVICES += glinet_gl-ar750
define Device/glinet_gl-mifi
SOC := ar9331
DEVICE_VENDOR := GL.iNET
DEVICE_MODEL := GL-MiFi
DEVICE_PACKAGES := kmod-usb-chipidea2
IMAGE_SIZE := 16000k
SUPPORTED_DEVICES += gl-mifi
endef
TARGET_DEVICES += glinet_gl-mifi
define Device/glinet_gl-usb150
SOC := ar9331
DEVICE_VENDOR := GL.iNET
DEVICE_MODEL := GL-USB150
IMAGE_SIZE := 16000k
SUPPORTED_DEVICES += gl-usb150
endef
TARGET_DEVICES += glinet_gl-usb150
define Device/glinet_gl-x300b
SOC := qca9531
DEVICE_VENDOR := GL.iNet
DEVICE_MODEL := GL-X300B
DEVICE_PACKAGES := kmod-usb2
IMAGE_SIZE := 16000k
endef
TARGET_DEVICES += glinet_gl-x300b
define Device/glinet_gl-x750
SOC := qca9531
DEVICE_VENDOR := GL.iNet
DEVICE_MODEL := GL-X750
DEVICE_PACKAGES := kmod-usb2 kmod-ath10k-ct ath10k-firmware-qca9887-ct
IMAGE_SIZE := 16000k
endef
TARGET_DEVICES += glinet_gl-x750
define Device/hak5_lan-turtle
$(Device/tplink-16mlzma)
SOC := ar9331
DEVICE_VENDOR := Hak5
DEVICE_MODEL := LAN Turtle
TPLINK_HWID := 0x5348334c
IMAGES := sysupgrade.bin
DEVICE_PACKAGES := kmod-usb-chipidea2 -iwinfo -kmod-ath9k -swconfig \
-uboot-envtools -wpad-basic-wolfssl
SUPPORTED_DEVICES += lan-turtle
endef
TARGET_DEVICES += hak5_lan-turtle
define Device/hak5_packet-squirrel
$(Device/tplink-16mlzma)
SOC := ar9331
DEVICE_VENDOR := Hak5
DEVICE_MODEL := Packet Squirrel
TPLINK_HWID := 0x5351524c
IMAGES := sysupgrade.bin
DEVICE_PACKAGES := kmod-usb-chipidea2 -iwinfo -kmod-ath9k -swconfig \
-uboot-envtools -wpad-basic-wolfssl
SUPPORTED_DEVICES += packet-squirrel
endef
TARGET_DEVICES += hak5_packet-squirrel
define Device/hak5_wifi-pineapple-nano
$(Device/tplink-16mlzma)
SOC := ar9331
DEVICE_VENDOR := Hak5
DEVICE_MODEL := WiFi Pineapple NANO
TPLINK_HWID := 0x4e414e4f
IMAGES := sysupgrade.bin
DEVICE_PACKAGES := kmod-ath9k-htc kmod-usb-chipidea2 kmod-usb-storage \
-swconfig -uboot-envtools
SUPPORTED_DEVICES += wifi-pineapple-nano
endef
TARGET_DEVICES += hak5_wifi-pineapple-nano
define Device/hiwifi_hc6361
SOC := ar9331
DEVICE_VENDOR := HiWiFi
DEVICE_MODEL := HC6361
DEVICE_PACKAGES := kmod-usb-core kmod-usb2 kmod-usb-chipidea2 kmod-usb-storage \
kmod-fs-ext4 kmod-nls-iso8859-1 e2fsprogs
BOARDNAME := HiWiFi-HC6361
KERNEL := kernel-bin | append-dtb | lzma | uImage lzma | pad-to $$(BLOCKSIZE)
IMAGE_SIZE := 16128k
endef
TARGET_DEVICES += hiwifi_hc6361
define Device/iodata_etg3-r
SOC := ar9342
DEVICE_VENDOR := I-O DATA
DEVICE_MODEL := ETG3-R
IMAGE_SIZE := 7680k
DEVICE_PACKAGES := -iwinfo -kmod-ath9k -wpad-basic-wolfssl
endef
TARGET_DEVICES += iodata_etg3-r
define Device/iodata_wn-ac1167dgr
SOC := qca9557
DEVICE_VENDOR := I-O DATA
DEVICE_MODEL := WN-AC1167DGR
IMAGE_SIZE := 14656k
IMAGES += factory.bin
IMAGE/factory.bin := append-kernel | pad-to $$$$(BLOCKSIZE) | \
append-rootfs | pad-rootfs | check-size | \
senao-header -r 0x30a -p 0x61 -t 2
DEVICE_PACKAGES := kmod-usb2 kmod-ath10k-ct ath10k-firmware-qca988x-ct
endef
TARGET_DEVICES += iodata_wn-ac1167dgr
define Device/iodata_wn-ac1600dgr
SOC := qca9557
DEVICE_VENDOR := I-O DATA
DEVICE_MODEL := WN-AC1600DGR
IMAGE_SIZE := 14656k
IMAGES += factory.bin
IMAGE/factory.bin := append-kernel | pad-to $$$$(BLOCKSIZE) | \
append-rootfs | pad-rootfs | check-size | \
senao-header -r 0x30a -p 0x60 -t 2 -v 200
DEVICE_PACKAGES := kmod-usb2 kmod-ath10k-ct ath10k-firmware-qca988x-ct
endef
TARGET_DEVICES += iodata_wn-ac1600dgr
define Device/iodata_wn-ac1600dgr2
SOC := qca9557
DEVICE_VENDOR := I-O DATA
DEVICE_MODEL := WN-AC1600DGR2/DGR3
IMAGE_SIZE := 14656k
IMAGES += dgr2-dgr3-factory.bin
IMAGE/dgr2-dgr3-factory.bin := append-kernel | pad-to $$$$(BLOCKSIZE) | \
append-rootfs | pad-rootfs | check-size | \
senao-header -r 0x30a -p 0x60 -t 2 -v 200
DEVICE_PACKAGES := kmod-usb2 kmod-ath10k-ct ath10k-firmware-qca988x-ct
endef
TARGET_DEVICES += iodata_wn-ac1600dgr2
define Device/iodata_wn-ag300dgr
SOC := ar1022
DEVICE_VENDOR := I-O DATA
DEVICE_MODEL := WN-AG300DGR
IMAGE_SIZE := 15424k
IMAGES += factory.bin
IMAGE/factory.bin := append-kernel | pad-to $$$$(BLOCKSIZE) | \
append-rootfs | pad-rootfs | check-size | \
senao-header -r 0x30a -p 0x47 -t 2
DEVICE_PACKAGES := kmod-usb2
endef
TARGET_DEVICES += iodata_wn-ag300dgr
define Device/jjplus_ja76pf2
SOC := ar7161
DEVICE_VENDOR := jjPlus
DEVICE_MODEL := JA76PF2
DEVICE_PACKAGES += -kmod-ath9k -swconfig -wpad-basic-wolfssl -uboot-envtools fconfig kmod-hwmon-lm75
LOADER_TYPE := bin
LOADER_FLASH_OFFS := 0x60000
COMPILE := loader-$(1).bin
COMPILE/loader-$(1).bin := loader-okli-compile | lzma | pad-to 128k
ARTIFACTS := loader.bin
ARTIFACT/loader.bin := append-loader-okli $(1)
IMAGES += firmware.bin
IMAGE/firmware.bin := append-kernel | uImage lzma -M 0x4f4b4c49 | pad-to $$$$(BLOCKSIZE) | \
append-rootfs | pad-rootfs | pad-to $$$$(BLOCKSIZE) | check-size
IMAGE/sysupgrade.bin := $$(IMAGE/firmware.bin) | \
sysupgrade-tar kernel=$$$$(KDIR)/loader-$(1).bin rootfs=$$$$@ | append-metadata
KERNEL := kernel-bin | append-dtb | lzma
KERNEL_INITRAMFS := kernel-bin | append-dtb
IMAGE_SIZE := 15872k
DEVICE_COMPAT_VERSION := 2.0
DEVICE_COMPAT_MESSAGE := Partition design has changed compared to older versions (19.07 and 21.02) \
due to kernel drivers restrictions. Upgrade via sysupgrade mechanism is one way operation. \
Downgrading OpenWrt version will involve usage of bootloader command line interface.
endef
TARGET_DEVICES += jjplus_ja76pf2
define Device/jjplus_jwap230
SOC := qca9558
DEVICE_VENDOR := jjPlus
DEVICE_MODEL := JWAP230
IMAGE_SIZE := 16000k
endef
TARGET_DEVICES += jjplus_jwap230
define Device/joyit_jt-or750i
SOC := qca9531
DEVICE_VENDOR := Joy-IT
DEVICE_MODEL := JT-OR750i
DEVICE_PACKAGES := kmod-ath10k-ct ath10k-firmware-qca9887-ct
IMAGE_SIZE := 16000k
endef
TARGET_DEVICES += joyit_jt-or750i
define Device/letv_lba-047-ch
$(Device/loader-okli-uimage)
SOC := qca9531
DEVICE_VENDOR := Letv
DEVICE_MODEL := LBA-047-CH
IMAGE_SIZE := 15936k
LOADER_FLASH_OFFS := 0x50000
KERNEL := kernel-bin | append-dtb | lzma | uImage lzma -M 0x4f4b4c49
IMAGES += factory.bin
IMAGE/factory.bin := append-kernel | pad-to $$$$(BLOCKSIZE) | \
append-rootfs | pad-rootfs | check-size | pad-to 14528k | \
append-loader-okli-uimage $(1) | pad-to 64k
endef
TARGET_DEVICES += letv_lba-047-ch
define Device/librerouter_librerouter-v1
SOC := qca9558
DEVICE_VENDOR := Librerouter
DEVICE_MODEL := LibreRouter
DEVICE_VARIANT := v1
IMAGE_SIZE := 7936k
DEVICE_PACKAGES := kmod-usb2
endef
TARGET_DEVICES += librerouter_librerouter-v1
define Device/meraki_mr12
SOC := ar7242
DEVICE_VENDOR := Meraki
DEVICE_MODEL := MR12
IMAGE_SIZE := 15616k
DEVICE_PACKAGES := kmod-owl-loader rssileds
SUPPORTED_DEVICES += mr12
DEVICE_COMPAT_VERSION := 2.0
DEVICE_COMPAT_MESSAGE := Partitions differ from ar71xx version of MR12. Image format is incompatible. \
To use sysupgrade, you must change /lib/update/common.sh::get_image to prepend 128K zeroes to this image, \
and change the bootcmd in u-boot to "bootm 0xbf0a0000". After that, you can use "sysupgrade -F -n". \
Make sure you do not keep your old config, as ethernet setup is not compatible either. \
For more details, see the OpenWrt Wiki: https://openwrt.org/toh/meraki/MR12, \
or the commit message of the MR12 ath79 port on git.openwrt.org.
endef
TARGET_DEVICES += meraki_mr12
define Device/meraki_mr16
SOC := ar7161
DEVICE_VENDOR := Meraki
DEVICE_MODEL := MR16
IMAGE_SIZE := 15616k
DEVICE_PACKAGES := kmod-owl-loader
SUPPORTED_DEVICES += mr16
DEVICE_COMPAT_VERSION := 2.0
DEVICE_COMPAT_MESSAGE := Partitions differ from ar71xx version of MR16. Image format is incompatible. \
To use sysupgrade, you must change /lib/update/common.sh::get_image to prepend 128K zeroes to this image, \
and change the bootcmd in u-boot to "bootm 0xbf0a0000". After that, you can use "sysupgrade -F". \
For more details, see the OpenWrt Wiki: https://openwrt.org/toh/meraki/mr16, \
or the commit message of the MR16 ath79 port on git.openwrt.org.
endef
TARGET_DEVICES += meraki_mr16
define Device/mercury_mw4530r-v1
$(Device/tplink-8mlzma)
SOC := ar9344
DEVICE_VENDOR := Mercury
DEVICE_MODEL := MW4530R
DEVICE_VARIANT := v1
DEVICE_PACKAGES := kmod-usb2 kmod-usb-ledtrig-usbport
TPLINK_HWID := 0x45300001
SUPPORTED_DEVICES += tl-wdr4300
endef
TARGET_DEVICES += mercury_mw4530r-v1
define Device/nec_wx1200cr
DEVICE_VENDOR := NEC
IMAGE/default := append-kernel | pad-offset $$$$(BLOCKSIZE) 64 | append-rootfs
IMAGE/sysupgrade.bin := $$(IMAGE/default) | seama | pad-rootfs | \
check-size | append-metadata
DEVICE_PACKAGES := kmod-ath10k-ct ath10k-firmware-qca9888-ct
endef
define Device/nec_wf1200cr
$(Device/nec_wx1200cr)
SOC := qca9561
DEVICE_MODEL := Aterm WF1200CR
IMAGE_SIZE := 7680k
SEAMA_MTDBLOCK := 5
SEAMA_SIGNATURE := wrgac62_necpf.2016gui_wf1200cr
IMAGES += factory.bin
IMAGE/factory.bin := $$(IMAGE/default) | pad-rootfs -x 64 | seama | \
seama-seal | nec-enc ryztfyutcrqqo69d | check-size
endef
TARGET_DEVICES += nec_wf1200cr
define Device/nec_wg1200cr
$(Device/nec_wx1200cr)
SOC := qca9563
DEVICE_MODEL := Aterm WG1200CR
IMAGE_SIZE := 7616k
SEAMA_MTDBLOCK := 6
SEAMA_SIGNATURE := wrgac72_necpf.2016gui_wg1200cr
IMAGES += factory.bin
IMAGE/factory.bin := $$(IMAGE/default) | pad-rootfs -x 64 | seama | \
seama-seal | nec-enc 9gsiy9nzep452pad | check-size
endef
TARGET_DEVICES += nec_wg1200cr
define Device/nec_wg800hp
SOC := qca9563
DEVICE_VENDOR := NEC
DEVICE_MODEL := Aterm WG800HP
IMAGE_SIZE := 7104k
IMAGES += factory.bin
IMAGE/factory.bin := append-kernel | pad-to $$$$(BLOCKSIZE) | \
append-rootfs | pad-rootfs | check-size | \
xor-image -p 6A57190601121E4C004C1E1201061957 -x | nec-fw LASER_ATERM
DEVICE_PACKAGES := kmod-ath10k-ct-smallbuffers ath10k-firmware-qca9887-ct-full-htt
endef
TARGET_DEVICES += nec_wg800hp
define Device/netgear_ex6400_ex7300
$(Device/netgear_generic)
SOC := qca9558
UIMAGE_MAGIC := 0x27051956
NETGEAR_BOARD_ID := EX7300series
NETGEAR_HW_ID := 29765104+16+0+128
IMAGE_SIZE := 15552k
IMAGE/default := append-kernel | pad-offset $$$$(BLOCKSIZE) 64 | \
netgear-rootfs | pad-rootfs
IMAGE/sysupgrade.bin := $$(IMAGE/default) | check-size | append-metadata
IMAGE/factory.img := $$(IMAGE/default) | netgear-dni | check-size
DEVICE_PACKAGES := kmod-ath10k-ct ath10k-firmware-qca99x0-ct
endef
define Device/netgear_ex6400
$(Device/netgear_ex6400_ex7300)
DEVICE_MODEL := EX6400
endef
TARGET_DEVICES += netgear_ex6400
define Device/netgear_ex7300
$(Device/netgear_ex6400_ex7300)
DEVICE_MODEL := EX7300
endef
TARGET_DEVICES += netgear_ex7300
define Device/netgear_ex7300-v2
$(Device/netgear_generic)
SOC := qcn5502
DEVICE_MODEL := EX7300
DEVICE_VARIANT := v2
UIMAGE_MAGIC := 0x27051956
NETGEAR_BOARD_ID := EX7300v2series
NETGEAR_HW_ID := 29765907+16+0+128
IMAGE_SIZE := 14528k
IMAGE/default := append-kernel | pad-offset $$$$(BLOCKSIZE) 64 | \
netgear-rootfs | pad-rootfs
IMAGE/sysupgrade.bin := $$(IMAGE/default) | check-size | append-metadata
IMAGE/factory.img := $$(IMAGE/default) | check-size | netgear-dni
DEVICE_PACKAGES := kmod-ath10k-ct ath10k-firmware-qca9984-ct
endef
TARGET_DEVICES += netgear_ex7300-v2
define Device/netgear_wndap360
$(Device/netgear_generic)
SOC := ar7161
DEVICE_MODEL := WNDAP360
DEVICE_PACKAGES := kmod-leds-reset kmod-owl-loader
IMAGE_SIZE := 7744k
BLOCKSIZE := 256k
KERNEL := kernel-bin | append-dtb | gzip | uImage gzip
KERNEL_INITRAMFS := kernel-bin | append-dtb | uImage none
IMAGES := sysupgrade.bin
IMAGE/sysupgrade.bin := append-kernel | pad-to 64k | append-rootfs | pad-rootfs | \
check-size | append-metadata
endef
TARGET_DEVICES += netgear_wndap360
define Device/netgear_wndr3x00
$(Device/netgear_generic)
SOC := ar7161
DEVICE_PACKAGES := kmod-usb-ohci kmod-usb2 kmod-usb-ledtrig-usbport \
kmod-leds-reset kmod-owl-loader kmod-switch-rtl8366s
endef
define Device/netgear_wndr3700
$(Device/netgear_wndr3x00)
DEVICE_MODEL := WNDR3700
DEVICE_VARIANT := v1
UIMAGE_MAGIC := 0x33373030
NETGEAR_BOARD_ID := WNDR3700
IMAGE_SIZE := 7680k
IMAGES += factory-NA.img
IMAGE/factory-NA.img := $$(IMAGE/default) | netgear-dni NA | \
check-size
SUPPORTED_DEVICES += wndr3700
endef
TARGET_DEVICES += netgear_wndr3700
define Device/netgear_wndr3700-v2
$(Device/netgear_wndr3x00)
DEVICE_MODEL := WNDR3700
DEVICE_VARIANT := v2
UIMAGE_MAGIC := 0x33373031
NETGEAR_BOARD_ID := WNDR3700v2
NETGEAR_HW_ID := 29763654+16+64
IMAGE_SIZE := 15872k
SUPPORTED_DEVICES += wndr3700 netgear,wndr3700v2
endef
TARGET_DEVICES += netgear_wndr3700-v2
define Device/netgear_wndr3800
$(Device/netgear_wndr3x00)
DEVICE_MODEL := WNDR3800
UIMAGE_MAGIC := 0x33373031
NETGEAR_BOARD_ID := WNDR3800
NETGEAR_HW_ID := 29763654+16+128
IMAGE_SIZE := 15872k
SUPPORTED_DEVICES += wndr3700
endef
TARGET_DEVICES += netgear_wndr3800
define Device/netgear_wndr3800ch
$(Device/netgear_wndr3x00)
DEVICE_MODEL := WNDR3800CH
UIMAGE_MAGIC := 0x33373031
NETGEAR_BOARD_ID := WNDR3800CH
NETGEAR_HW_ID := 29763654+16+128
IMAGE_SIZE := 15872k
SUPPORTED_DEVICES += wndr3700
endef
TARGET_DEVICES += netgear_wndr3800ch
define Device/netgear_wndrmac-v1
$(Device/netgear_wndr3x00)
DEVICE_MODEL := WNDRMAC
DEVICE_VARIANT := v1
UIMAGE_MAGIC := 0x33373031
NETGEAR_BOARD_ID := WNDRMAC
NETGEAR_HW_ID := 29763654+16+64
IMAGE_SIZE := 15872k
SUPPORTED_DEVICES += wndr3700
endef
TARGET_DEVICES += netgear_wndrmac-v1
define Device/netgear_wndrmac-v2
$(Device/netgear_wndr3x00)
DEVICE_MODEL := WNDRMAC
DEVICE_VARIANT := v2
UIMAGE_MAGIC := 0x33373031
NETGEAR_BOARD_ID := WNDRMACv2
NETGEAR_HW_ID := 29763654+16+128
IMAGE_SIZE := 15872k
SUPPORTED_DEVICES += wndr3700
endef
TARGET_DEVICES += netgear_wndrmac-v2
define Device/netgear_wnr2200_common
$(Device/netgear_generic)
SOC := ar7241
DEVICE_MODEL := WNR2200
DEVICE_PACKAGES := kmod-usb2 kmod-usb-ledtrig-usbport
UIMAGE_MAGIC := 0x32323030
NETGEAR_BOARD_ID := wnr2200
endef
define Device/netgear_wnr2200-8m
$(Device/netgear_wnr2200_common)
DEVICE_VARIANT := 8M
NETGEAR_HW_ID := 29763600+08+64
IMAGE_SIZE := 7808k
IMAGES += factory-NA.img
IMAGE/factory-NA.img := $$(IMAGE/default) | netgear-dni NA | \
check-size
SUPPORTED_DEVICES += wnr2200
endef
TARGET_DEVICES += netgear_wnr2200-8m
define Device/netgear_wnr2200-16m
$(Device/netgear_wnr2200_common)
DEVICE_VARIANT := 16M
DEVICE_ALT0_VENDOR := NETGEAR
DEVICE_ALT0_MODEL := WNR2200
DEVICE_ALT0_VARIANT := CN/RU
NETGEAR_HW_ID :=
IMAGE_SIZE := 16000k
endef
TARGET_DEVICES += netgear_wnr2200-16m
define Device/ocedo_koala
SOC := qca9558
DEVICE_VENDOR := Ocedo
DEVICE_MODEL := Koala
DEVICE_PACKAGES := kmod-ath10k-ct ath10k-firmware-qca988x-ct
SUPPORTED_DEVICES += koala
IMAGE_SIZE := 7424k
endef
TARGET_DEVICES += ocedo_koala
define Device/ocedo_raccoon
SOC := ar9344
DEVICE_VENDOR := Ocedo
DEVICE_MODEL := Raccoon
IMAGE_SIZE := 7424k
endef
TARGET_DEVICES += ocedo_raccoon
define Device/ocedo_ursus
SOC := qca9558
DEVICE_VENDOR := Ocedo
DEVICE_MODEL := Ursus
DEVICE_PACKAGES := kmod-ath10k-ct ath10k-firmware-qca988x-ct
IMAGE_SIZE := 7424k
endef
TARGET_DEVICES += ocedo_ursus
define Device/onion_omega
$(Device/tplink-16mlzma)
SOC := ar9331
DEVICE_VENDOR := Onion
DEVICE_MODEL := Omega
DEVICE_PACKAGES := kmod-usb-chipidea2
SUPPORTED_DEVICES += onion-omega
KERNEL_INITRAMFS := kernel-bin | append-dtb | lzma | uImage lzma
IMAGE_SIZE := 16192k
TPLINK_HWID := 0x04700001
endef
TARGET_DEVICES += onion_omega
define Device/openmesh_common_64k
DEVICE_VENDOR := OpenMesh
DEVICE_PACKAGES := uboot-envtools
IMAGE_SIZE := 7808k
OPENMESH_CE_TYPE :=
KERNEL := kernel-bin | append-dtb | lzma | uImage lzma | \
pad-to $$(BLOCKSIZE)
IMAGE/sysupgrade.bin := append-rootfs | pad-rootfs | \
openmesh-image ce_type=$$$$(OPENMESH_CE_TYPE) | append-metadata
endef
define Device/openmesh_common_256k
DEVICE_VENDOR := OpenMesh
DEVICE_PACKAGES := uboot-envtools
IMAGE_SIZE := 7168k
BLOCKSIZE := 256k
OPENMESH_CE_TYPE :=
KERNEL := kernel-bin | append-dtb | lzma | uImage lzma | \
pad-to $$(BLOCKSIZE)
IMAGE/sysupgrade.bin := append-rootfs | pad-rootfs | \
openmesh-image ce_type=$$$$(OPENMESH_CE_TYPE) | append-metadata
endef
define Device/openmesh_a40
$(Device/openmesh_common_64k)
SOC := qca9558
DEVICE_MODEL := A40
DEVICE_PACKAGES += kmod-ath10k-ct ath10k-firmware-qca988x-ct kmod-usb2
OPENMESH_CE_TYPE := A60
SUPPORTED_DEVICES += a40
endef
TARGET_DEVICES += openmesh_a40
define Device/openmesh_a60
$(Device/openmesh_common_64k)
SOC := qca9558
DEVICE_MODEL := A60
DEVICE_PACKAGES += kmod-ath10k-ct ath10k-firmware-qca988x-ct kmod-usb2
OPENMESH_CE_TYPE := A60
SUPPORTED_DEVICES += a60
endef
TARGET_DEVICES += openmesh_a60
define Device/openmesh_mr600-v1
$(Device/openmesh_common_64k)
SOC := ar9344
DEVICE_MODEL := MR600
DEVICE_VARIANT := v1
OPENMESH_CE_TYPE := MR600
SUPPORTED_DEVICES += mr600
endef
TARGET_DEVICES += openmesh_mr600-v1
define Device/openmesh_mr600-v2
$(Device/openmesh_common_64k)
SOC := ar9344
DEVICE_MODEL := MR600
DEVICE_VARIANT := v2
OPENMESH_CE_TYPE := MR600
SUPPORTED_DEVICES += mr600v2
endef
TARGET_DEVICES += openmesh_mr600-v2
define Device/openmesh_mr900-v1
$(Device/openmesh_common_64k)
SOC := qca9558
DEVICE_MODEL := MR900
DEVICE_VARIANT := v1
OPENMESH_CE_TYPE := MR900
SUPPORTED_DEVICES += mr900
endef
TARGET_DEVICES += openmesh_mr900-v1
define Device/openmesh_mr900-v2
$(Device/openmesh_common_64k)
SOC := qca9558
DEVICE_MODEL := MR900
DEVICE_VARIANT := v2
OPENMESH_CE_TYPE := MR900
SUPPORTED_DEVICES += mr900v2
endef
TARGET_DEVICES += openmesh_mr900-v2
define Device/openmesh_mr1750-v1
$(Device/openmesh_common_64k)
SOC := qca9558
DEVICE_MODEL := MR1750
DEVICE_VARIANT := v1
DEVICE_PACKAGES += kmod-ath10k-ct ath10k-firmware-qca988x-ct
OPENMESH_CE_TYPE := MR1750
SUPPORTED_DEVICES += mr1750
endef
TARGET_DEVICES += openmesh_mr1750-v1
define Device/openmesh_mr1750-v2
$(Device/openmesh_common_64k)
SOC := qca9558
DEVICE_MODEL := MR1750
DEVICE_VARIANT := v2
DEVICE_PACKAGES += kmod-ath10k-ct ath10k-firmware-qca988x-ct
OPENMESH_CE_TYPE := MR1750
SUPPORTED_DEVICES += mr1750v2
endef
TARGET_DEVICES += openmesh_mr1750-v2
define Device/openmesh_om2p-v1
$(Device/openmesh_common_256k)
SOC := ar7240
DEVICE_MODEL := OM2P
DEVICE_VARIANT := v1
OPENMESH_CE_TYPE := OM2P
SUPPORTED_DEVICES += om2p
endef
TARGET_DEVICES += openmesh_om2p-v1
define Device/openmesh_om2p-v2
$(Device/openmesh_common_256k)
SOC := ar9330
DEVICE_MODEL := OM2P
DEVICE_VARIANT := v2
OPENMESH_CE_TYPE := OM2P
SUPPORTED_DEVICES += om2pv2
endef
TARGET_DEVICES += openmesh_om2p-v2
define Device/openmesh_om2p-v4
$(Device/openmesh_common_256k)
SOC := qca9533
DEVICE_MODEL := OM2P
DEVICE_VARIANT := v4
OPENMESH_CE_TYPE := OM2P
SUPPORTED_DEVICES += om2pv4
endef
TARGET_DEVICES += openmesh_om2p-v4
define Device/openmesh_om2p-hs-v1
$(Device/openmesh_common_256k)
SOC := ar9341
DEVICE_MODEL := OM2P-HS
DEVICE_VARIANT := v1
OPENMESH_CE_TYPE := OM2P
SUPPORTED_DEVICES += om2p-hs
endef
TARGET_DEVICES += openmesh_om2p-hs-v1
define Device/openmesh_om2p-hs-v2
$(Device/openmesh_common_256k)
SOC := ar9341
DEVICE_MODEL := OM2P-HS
DEVICE_VARIANT := v2
OPENMESH_CE_TYPE := OM2P
SUPPORTED_DEVICES += om2p-hsv2
endef
TARGET_DEVICES += openmesh_om2p-hs-v2
define Device/openmesh_om2p-hs-v3
$(Device/openmesh_common_256k)
SOC := ar9341
DEVICE_MODEL := OM2P-HS
DEVICE_VARIANT := v3
OPENMESH_CE_TYPE := OM2P
SUPPORTED_DEVICES += om2p-hsv3
endef
TARGET_DEVICES += openmesh_om2p-hs-v3
define Device/openmesh_om2p-hs-v4
$(Device/openmesh_common_256k)
SOC := qca9533
DEVICE_MODEL := OM2P-HS
DEVICE_VARIANT := v4
OPENMESH_CE_TYPE := OM2P
SUPPORTED_DEVICES += om2p-hsv4
endef
TARGET_DEVICES += openmesh_om2p-hs-v4
define Device/openmesh_om2p-lc
$(Device/openmesh_common_256k)
SOC := ar9330
DEVICE_MODEL := OM2P-LC
OPENMESH_CE_TYPE := OM2P
SUPPORTED_DEVICES += om2p-lc
endef
TARGET_DEVICES += openmesh_om2p-lc
define Device/openmesh_om5p
$(Device/openmesh_common_64k)
SOC := ar9344
DEVICE_MODEL := OM5P
OPENMESH_CE_TYPE := OM5P
SUPPORTED_DEVICES += om5p
endef
TARGET_DEVICES += openmesh_om5p
define Device/openmesh_om5p-ac-v1
$(Device/openmesh_common_64k)
SOC := qca9558
DEVICE_MODEL := OM5P-AC
DEVICE_VARIANT := v1
DEVICE_PACKAGES += kmod-ath10k-ct ath10k-firmware-qca988x-ct
OPENMESH_CE_TYPE := OM5PAC
SUPPORTED_DEVICES += om5p-ac
endef
TARGET_DEVICES += openmesh_om5p-ac-v1
define Device/openmesh_om5p-ac-v2
$(Device/openmesh_common_64k)
SOC := qca9558
DEVICE_MODEL := OM5P-AC
DEVICE_VARIANT := v2
DEVICE_PACKAGES += kmod-ath10k-ct ath10k-firmware-qca988x-ct
OPENMESH_CE_TYPE := OM5PAC
SUPPORTED_DEVICES += om5p-acv2
endef
TARGET_DEVICES += openmesh_om5p-ac-v2
define Device/openmesh_om5p-an
$(Device/openmesh_common_64k)
SOC := ar9344
DEVICE_MODEL := OM5P-AN
OPENMESH_CE_TYPE := OM5P
SUPPORTED_DEVICES += om5p-an
endef
TARGET_DEVICES += openmesh_om5p-an
define Device/pcs_cap324
SOC := ar9344
DEVICE_VENDOR := PowerCloud Systems
DEVICE_MODEL := CAP324
IMAGE_SIZE := 16000k
SUPPORTED_DEVICES += cap324
endef
TARGET_DEVICES += pcs_cap324
define Device/pcs_cr3000
SOC := ar9341
DEVICE_VENDOR := PowerCloud Systems
DEVICE_MODEL := CR3000
IMAGE_SIZE := 7808k
SUPPORTED_DEVICES += cr3000
endef
TARGET_DEVICES += pcs_cr3000
define Device/pcs_cr5000
SOC := ar9344
DEVICE_VENDOR := PowerCloud Systems
DEVICE_MODEL := CR5000
DEVICE_PACKAGES := kmod-usb2
IMAGE_SIZE := 7808k
SUPPORTED_DEVICES += cr5000
endef
TARGET_DEVICES += pcs_cr5000
define Device/phicomm_k2t
SOC := qca9563
DEVICE_VENDOR := Phicomm
DEVICE_MODEL := K2T
IMAGE_SIZE := 15744k
IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | \
check-size | append-metadata
DEVICE_PACKAGES := kmod-leds-reset kmod-ath10k-ct-smallbuffers ath10k-firmware-qca9888-ct
endef
TARGET_DEVICES += phicomm_k2t
define Device/pisen_ts-d084
$(Device/tplink-8mlzma)
SOC := ar9331
DEVICE_VENDOR := PISEN
DEVICE_MODEL := TS-D084
DEVICE_PACKAGES := kmod-usb-chipidea2
TPLINK_HWID := 0x07030101
endef
TARGET_DEVICES += pisen_ts-d084
define Device/pisen_wmb001n
$(Device/loader-okli-uimage)
SOC := ar9341
DEVICE_VENDOR := PISEN
DEVICE_MODEL := WMB001N
IMAGE_SIZE := 14080k
DEVICE_PACKAGES := kmod-i2c-gpio kmod-usb2
LOADER_FLASH_OFFS := 0x20000
KERNEL := kernel-bin | append-dtb | lzma | uImage lzma -M 0x4f4b4c49
IMAGES += factory.bin
IMAGE/factory.bin := $$(IMAGE/sysupgrade.bin) | pisen_wmb001n-factory $(1)
endef
TARGET_DEVICES += pisen_wmb001n
define Device/pisen_wmm003n
$(Device/tplink-8mlzma)
SOC := ar9331
DEVICE_VENDOR := PISEN
DEVICE_MODEL := Cloud Easy Power (WMM003N)
DEVICE_PACKAGES := kmod-usb-chipidea2
TPLINK_HWID := 0x07030101
endef
TARGET_DEVICES += pisen_wmm003n
define Device/plasmacloud_pa300-common
SOC := qca9533
DEVICE_VENDOR := Plasma Cloud
DEVICE_PACKAGES := uboot-envtools
IMAGE_SIZE := 7168k
IMAGES += factory.bin
KERNEL := kernel-bin | append-dtb | lzma | uImage lzma | pad-to $$(BLOCKSIZE)
IMAGE/factory.bin := append-rootfs | pad-rootfs | openmesh-image ce_type=PA300
IMAGE/sysupgrade.bin := append-rootfs | pad-rootfs | sysupgrade-tar rootfs=$$$$@ | append-metadata
endef
define Device/plasmacloud_pa300
$(Device/plasmacloud_pa300-common)
DEVICE_MODEL := PA300
endef
TARGET_DEVICES += plasmacloud_pa300
define Device/plasmacloud_pa300e
$(Device/plasmacloud_pa300-common)
DEVICE_MODEL := PA300E
endef
TARGET_DEVICES += plasmacloud_pa300e
define Device/qca_ap143
$(Device/loader-okli-uimage)
SOC := qca9533
DEVICE_VENDOR := Qualcomm Atheros
DEVICE_MODEL := AP143
DEVICE_PACKAGES := kmod-usb2
SUPPORTED_DEVICES += ap143
LOADER_FLASH_OFFS := 0x50000
KERNEL := kernel-bin | append-dtb | lzma | uImage lzma -M 0x4f4b4c49
endef
define Device/qca_ap143-8m
$(Device/qca_ap143)
DEVICE_VARIANT := (8M)
IMAGE_SIZE := 7744k
IMAGES += factory.bin
IMAGE/factory.bin := append-kernel | pad-to $$$$(BLOCKSIZE) | \
append-rootfs | pad-rootfs | check-size | pad-to 6336k | \
append-loader-okli-uimage $(1) | pad-to 64k
endef
TARGET_DEVICES += qca_ap143-8m
define Device/qca_ap143-16m
$(Device/qca_ap143)
DEVICE_VARIANT := (16M)
IMAGE_SIZE := 15936k
IMAGES += factory.bin
IMAGE/factory.bin := append-kernel | pad-to $$$$(BLOCKSIZE) | \
append-rootfs | pad-rootfs | check-size | pad-to 14528k | \
append-loader-okli-uimage $(1) | pad-to 64k
endef
TARGET_DEVICES += qca_ap143-16m
define Device/qihoo_c301
$(Device/seama)
SOC := ar9344
DEVICE_VENDOR := Qihoo
DEVICE_MODEL := C301
DEVICE_PACKAGES := kmod-usb2 kmod-ath10k-ct ath10k-firmware-qca988x-ct \
uboot-envtools
IMAGE_SIZE := 15744k
SEAMA_SIGNATURE := wrgac26_qihoo360_360rg
SUPPORTED_DEVICES += qihoo-c301
endef
TARGET_DEVICES += qihoo_c301
define Device/qxwlan_e1700ac-v2
SOC := qca9563
DEVICE_VENDOR := Qxwlan
DEVICE_MODEL := E1700AC
DEVICE_PACKAGES := kmod-usb2 kmod-ath10k-ct ath10k-firmware-qca988x-ct
SUPPORTED_DEVICES += e1700ac-v2
endef
define Device/qxwlan_e1700ac-v2-16m
$(Device/qxwlan_e1700ac-v2)
DEVICE_VARIANT := v2 (16M)
IMAGE_SIZE := 15936k
endef
TARGET_DEVICES += qxwlan_e1700ac-v2-16m
define Device/qxwlan_e1700ac-v2-8m
$(Device/qxwlan_e1700ac-v2)
DEVICE_VARIANT := v2 (8M)
IMAGE_SIZE := 7744k
endef
TARGET_DEVICES += qxwlan_e1700ac-v2-8m
define Device/qxwlan_e558-v2
SOC := qca9558
DEVICE_VENDOR := Qxwlan
DEVICE_MODEL := E558
DEVICE_PACKAGES := kmod-usb2
SUPPORTED_DEVICES += e558-v2
endef
define Device/qxwlan_e558-v2-16m
$(Device/qxwlan_e558-v2)
DEVICE_VARIANT := v2 (16M)
IMAGE_SIZE := 15936k
endef
TARGET_DEVICES += qxwlan_e558-v2-16m
define Device/qxwlan_e558-v2-8m
$(Device/qxwlan_e558-v2)
DEVICE_VARIANT := v2 (8M)
IMAGE_SIZE := 7744k
endef
TARGET_DEVICES += qxwlan_e558-v2-8m
define Device/qxwlan_e600g-v2
SOC := qca9531
DEVICE_VENDOR := Qxwlan
DEVICE_MODEL := E600G
DEVICE_PACKAGES := kmod-usb2
SUPPORTED_DEVICES += e600g-v2
endef
define Device/qxwlan_e600g-v2-16m
$(Device/qxwlan_e600g-v2)
DEVICE_VARIANT := v2 (16M)
IMAGE_SIZE := 15936k
endef
TARGET_DEVICES += qxwlan_e600g-v2-16m
define Device/qxwlan_e600g-v2-8m
$(Device/qxwlan_e600g-v2)
DEVICE_VARIANT := v2 (8M)
IMAGE_SIZE := 7744k
endef
TARGET_DEVICES += qxwlan_e600g-v2-8m
define Device/qxwlan_e600gac-v2
SOC := qca9531
DEVICE_VENDOR := Qxwlan
DEVICE_MODEL := E600GAC
DEVICE_PACKAGES := kmod-ath10k-ct ath10k-firmware-qca9887-ct
SUPPORTED_DEVICES += e600gac-v2
endef
define Device/qxwlan_e600gac-v2-16m
$(Device/qxwlan_e600gac-v2)
DEVICE_VARIANT := v2 (16M)
IMAGE_SIZE := 15936k
endef
TARGET_DEVICES += qxwlan_e600gac-v2-16m
define Device/qxwlan_e600gac-v2-8m
$(Device/qxwlan_e600gac-v2)
DEVICE_VARIANT := v2 (8M)
IMAGE_SIZE := 7744k
endef
TARGET_DEVICES += qxwlan_e600gac-v2-8m
define Device/qxwlan_e750a-v4
SOC := ar9344
DEVICE_VENDOR := Qxwlan
DEVICE_MODEL := E750A
DEVICE_PACKAGES := kmod-usb2
SUPPORTED_DEVICES += e750a-v4
endef
define Device/qxwlan_e750a-v4-16m
$(Device/qxwlan_e750a-v4)
DEVICE_VARIANT := v4 (16M)
IMAGE_SIZE := 15936k
endef
TARGET_DEVICES += qxwlan_e750a-v4-16m
define Device/qxwlan_e750a-v4-8m
$(Device/qxwlan_e750a-v4)
DEVICE_VARIANT := v4 (8M)
IMAGE_SIZE := 7744k
endef
TARGET_DEVICES += qxwlan_e750a-v4-8m
define Device/qxwlan_e750g-v8
SOC := ar9344
DEVICE_VENDOR := Qxwlan
DEVICE_MODEL := E750G
DEVICE_PACKAGES := kmod-usb2
SUPPORTED_DEVICES += e750g-v8
endef
define Device/qxwlan_e750g-v8-16m
$(Device/qxwlan_e750g-v8)
DEVICE_VARIANT := v8 (16M)
IMAGE_SIZE := 15936k
endef
TARGET_DEVICES += qxwlan_e750g-v8-16m
define Device/qxwlan_e750g-v8-8m
$(Device/qxwlan_e750g-v8)
DEVICE_VARIANT := v8 (8M)
IMAGE_SIZE := 7744k
endef
TARGET_DEVICES += qxwlan_e750g-v8-8m
define Device/rosinson_wr818
SOC := qca9563
DEVICE_VENDOR := Rosinson
DEVICE_MODEL := WR818
IMAGE_SIZE := 15872k
DEVICE_PACKAGES := kmod-usb2 kmod-usb-ledtrig-usbport
endef
TARGET_DEVICES += rosinson_wr818
define Device/ruckus_zf73xx_common
DEVICE_VENDOR := Ruckus
DEVICE_PACKAGES := -swconfig kmod-usb2 kmod-usb-chipidea2
IMAGE_SIZE := 31744k
LOADER_TYPE := bin
KERNEL := kernel-bin | append-dtb | lzma | loader-kernel | uImage none
KERNEL_INITRAMFS := kernel-bin | append-dtb | lzma | loader-kernel | uImage none
endef
define Device/ruckus_zf7321
$(Device/ruckus_zf73xx_common)
SOC := ar9342
DEVICE_MODEL := ZoneFlex 7321[-U]
endef
TARGET_DEVICES += ruckus_zf7321
define Device/ruckus_zf7372
$(Device/ruckus_zf73xx_common)
SOC := ar9344
DEVICE_MODEL := ZoneFlex 7352/7372[-E/-U]
endef
TARGET_DEVICES += ruckus_zf7372
define Device/samsung_wam250
SOC := ar9344
DEVICE_VENDOR := Samsung
DEVICE_MODEL := WAM250
IMAGE_SIZE := 15872k
DEVICE_PACKAGES := kmod-usb2
SUPPORTED_DEVICES += wam250
endef
TARGET_DEVICES += samsung_wam250
define Device/siemens_ws-ap3610
SOC := ar7161
DEVICE_VENDOR := Siemens
DEVICE_MODEL := WS-AP3610
IMAGE_SIZE := 14336k
BLOCKSIZE := 256k
LOADER_TYPE := bin
LOADER_FLASH_OFFS := 0x82000
COMPILE := loader-$(1).bin
COMPILE/loader-$(1).bin := loader-okli-compile
KERNEL := kernel-bin | append-dtb | lzma | uImage lzma -M 0x4f4b4c49 | loader-okli $(1) 8128 | uImage none
KERNEL_INITRAMFS := kernel-bin | append-dtb | uImage none
endef
TARGET_DEVICES += siemens_ws-ap3610
define Device/sitecom_wlr-7100
SOC := ar1022
DEVICE_VENDOR := Sitecom
DEVICE_MODEL := WLR-7100
DEVICE_PACKAGES := ath10k-firmware-qca988x-ct kmod-ath10k-ct-smallbuffers kmod-usb2
IMAGES += factory.dlf
IMAGE/factory.dlf := append-kernel | pad-to $$$$(BLOCKSIZE) | \
append-rootfs | pad-rootfs | check-size | \
senao-header -r 0x222 -p 0x53 -t 2
IMAGE_SIZE := 7488k
endef
TARGET_DEVICES += sitecom_wlr-7100
define Device/sitecom_wlr-8100
SOC := qca9558
DEVICE_VENDOR := Sitecom
DEVICE_MODEL := WLR-8100
DEVICE_ALT0_VENDOR := Sitecom
DEVICE_ALT0_MODEL := X8 AC1750
DEVICE_PACKAGES := ath10k-firmware-qca988x-ct kmod-ath10k-ct kmod-usb2 kmod-usb3
SUPPORTED_DEVICES += wlr8100
IMAGES += factory.dlf
IMAGE/factory.dlf := append-kernel | pad-to $$$$(BLOCKSIZE) | \
append-rootfs | pad-rootfs | check-size | \
senao-header -r 0x222 -p 0x56 -t 2
IMAGE_SIZE := 15424k
endef
TARGET_DEVICES += sitecom_wlr-8100
define Device/sophos_ap15
SOC := qca9558
DEVICE_VENDOR := Sophos
DEVICE_MODEL := AP15
DEVICE_PACKAGES := kmod-ath10k-ct ath10k-firmware-qca988x-ct
IMAGE_SIZE := 15936k
endef
TARGET_DEVICES += sophos_ap15
define Device/sophos_ap55
SOC := qca9558
DEVICE_VENDOR := Sophos
DEVICE_MODEL := AP55
DEVICE_PACKAGES := kmod-ath10k-ct ath10k-firmware-qca988x-ct kmod-usb2
IMAGE_SIZE := 15936k
endef
TARGET_DEVICES += sophos_ap55
define Device/sophos_ap55c
SOC := qca9558
DEVICE_VENDOR := Sophos
DEVICE_MODEL := AP55C
DEVICE_PACKAGES := kmod-ath10k-ct ath10k-firmware-qca988x-ct
IMAGE_SIZE := 15936k
endef
TARGET_DEVICES += sophos_ap55c
define Device/sophos_ap100
SOC := qca9558
DEVICE_VENDOR := Sophos
DEVICE_MODEL := AP100
DEVICE_PACKAGES := kmod-ath10k-ct ath10k-firmware-qca988x-ct kmod-usb2
IMAGE_SIZE := 15936k
endef
TARGET_DEVICES += sophos_ap100
define Device/sophos_ap100c
SOC := qca9558
DEVICE_VENDOR := Sophos
DEVICE_MODEL := AP100C
DEVICE_PACKAGES := kmod-ath10k-ct ath10k-firmware-qca988x-ct
IMAGE_SIZE := 15936k
endef
TARGET_DEVICES += sophos_ap100c
define Device/telco_t1
SOC := qca9531
DEVICE_VENDOR := Telco
DEVICE_MODEL := T1
DEVICE_PACKAGES := kmod-usb2 kmod-usb-net-qmi-wwan \
kmod-usb-serial-option uqmi -swconfig -uboot-envtools
IMAGE_SIZE := 16192k
SUPPORTED_DEVICES += telco_electronics,tel-t1
endef
TARGET_DEVICES += telco_t1
define Device/teltonika_rut230-v1
SOC := ar9331
DEVICE_VENDOR := Teltonika
DEVICE_MODEL := RUT230
DEVICE_VARIANT := v1
DEVICE_PACKAGES := kmod-usb-chipidea2 kmod-usb-acm kmod-usb-net-qmi-wwan \
uqmi -uboot-envtools
IMAGE_SIZE := 15552k
TPLINK_HWID := 0x32200002
TPLINK_HWREV := 0x1
TPLINK_HEADER_VERSION := 1
KERNEL := kernel-bin | append-dtb | lzma | teltonika-v1-header
KERNEL_INITRAMFS := kernel-bin | append-dtb | lzma | uImage lzma
IMAGES += factory.bin
IMAGE/factory.bin := append-kernel | pad-to $$$$(BLOCKSIZE) | append-rootfs |\
pad-rootfs | pad-extra 64 | teltonika-fw-fake-checksum 54 | check-size
IMAGE/sysupgrade.bin := append-kernel | pad-to $$$$(BLOCKSIZE) |\
append-rootfs | pad-rootfs | append-metadata |\
check-size
endef
TARGET_DEVICES += teltonika_rut230-v1
define Device/teltonika_rut955
SOC := ar9344
DEVICE_VENDOR := Teltonika
DEVICE_MODEL := RUT955
DEVICE_PACKAGES := kmod-usb2 kmod-usb-acm kmod-usb-net-qmi-wwan \
kmod-usb-serial-option kmod-hwmon-mcp3021 uqmi -uboot-envtools
IMAGE_SIZE := 15552k
TPLINK_HWID := 0x35000001
TPLINK_HWREV := 0x1
TPLINK_HEADER_VERSION := 1
KERNEL := kernel-bin | append-dtb | lzma | tplink-v1-header
KERNEL_INITRAMFS := kernel-bin | append-dtb | lzma | uImage lzma
IMAGES += factory.bin
IMAGE/factory.bin := append-kernel | pad-to $$$$(BLOCKSIZE) | append-rootfs |\
pad-rootfs | teltonika-fw-fake-checksum 20 | append-string master |\
append-md5sum-bin | check-size
IMAGE/sysupgrade.bin := append-kernel | pad-to $$$$(BLOCKSIZE) |\
append-rootfs | pad-rootfs | check-size | append-metadata
endef
TARGET_DEVICES += teltonika_rut955
define Device/teltonika_rut955-h7v3c0
$(Device/teltonika_rut955)
DEVICE_VARIANT := H7V3C0
endef
TARGET_DEVICES += teltonika_rut955-h7v3c0
define Device/trendnet_tew-823dru
SOC := qca9558
DEVICE_VENDOR := Trendnet
DEVICE_MODEL := TEW-823DRU
DEVICE_VARIANT := v1.0R
DEVICE_PACKAGES := kmod-usb2 kmod-ath10k-ct ath10k-firmware-qca988x-ct
SUPPORTED_DEVICES += tew-823dru
IMAGE_SIZE := 15296k
IMAGES := factory.bin sysupgrade.bin
IMAGE/default := append-kernel | pad-to $$$$(BLOCKSIZE) | append-rootfs | \
pad-rootfs
IMAGE/factory.bin := $$(IMAGE/default) | pad-offset $$$$(IMAGE_SIZE) 26 | \
append-string 00AP135AR9558-RT-131129-00 | check-size
IMAGE/sysupgrade.bin := $$(IMAGE/default) | check-size | append-metadata
endef
TARGET_DEVICES += trendnet_tew-823dru
define Device/wallys_dr531
SOC := qca9531
DEVICE_VENDOR := Wallys
DEVICE_MODEL := DR531
DEVICE_PACKAGES := kmod-usb2 rssileds
IMAGE_SIZE := 7808k
SUPPORTED_DEVICES += dr531
endef
TARGET_DEVICES += wallys_dr531
define Device/watchguard_ap100
$(Device/senao_loader_okli)
SOC := ar9344
DEVICE_VENDOR := WatchGuard
DEVICE_MODEL := AP100
IMAGE_SIZE := 12096k
LOADER_FLASH_OFFS := 0x220000
SENAO_IMGNAME := senao-ap100
WATCHGUARD_MAGIC := 82kdlzk2
IMAGE/factory.bin := append-kernel | pad-to $$$$(BLOCKSIZE) | append-rootfs | pad-rootfs | \
check-size | senao-tar-gz $$$$(SENAO_IMGNAME) | watchguard-cksum $$$$(WATCHGUARD_MAGIC)
endef
TARGET_DEVICES += watchguard_ap100
define Device/watchguard_ap200
$(Device/senao_loader_okli)
SOC := ar9344
DEVICE_VENDOR := WatchGuard
DEVICE_MODEL := AP200
IMAGE_SIZE := 12096k
LOADER_FLASH_OFFS := 0x220000
SENAO_IMGNAME := senao-ap200
WATCHGUARD_MAGIC := 82kdlzk2
IMAGE/factory.bin := append-kernel | pad-to $$$$(BLOCKSIZE) | append-rootfs | pad-rootfs | \
check-size | senao-tar-gz $$$$(SENAO_IMGNAME) | watchguard-cksum $$$$(WATCHGUARD_MAGIC)
endef
TARGET_DEVICES += watchguard_ap200
define Device/watchguard_ap300
$(Device/senao_loader_okli)
SOC := qca9558
DEVICE_VENDOR := WatchGuard
DEVICE_MODEL := AP300
DEVICE_PACKAGES := ath10k-firmware-qca988x-ct kmod-ath10k-ct
IMAGE_SIZE := 11584k
LOADER_FLASH_OFFS := 0x220000
SENAO_IMGNAME := senao-ap300
WATCHGUARD_MAGIC := 82kdlzk2
IMAGE/factory.bin := append-kernel | pad-to $$$$(BLOCKSIZE) | append-rootfs | pad-rootfs | \
check-size | senao-tar-gz $$$$(SENAO_IMGNAME) | watchguard-cksum $$$$(WATCHGUARD_MAGIC)
endef
TARGET_DEVICES += watchguard_ap300
define Device/wd_mynet-n600
$(Device/seama)
SOC := ar9344
DEVICE_VENDOR := Western Digital
DEVICE_MODEL := My Net N600
IMAGE_SIZE := 15872k
DEVICE_PACKAGES := kmod-usb2
SEAMA_SIGNATURE := wrgnd16_wd_db600
SUPPORTED_DEVICES += mynet-n600
endef
TARGET_DEVICES += wd_mynet-n600
define Device/wd_mynet-n750
$(Device/seama)
SOC := ar9344
DEVICE_VENDOR := Western Digital
DEVICE_MODEL := My Net N750
IMAGE_SIZE := 15872k
DEVICE_PACKAGES := kmod-usb2
SEAMA_SIGNATURE := wrgnd13_wd_av
SUPPORTED_DEVICES += mynet-n750
endef
TARGET_DEVICES += wd_mynet-n750
define Device/wd_mynet-wifi-rangeextender
SOC := ar9344
DEVICE_VENDOR := Western Digital
DEVICE_MODEL := My Net Wi-Fi Range Extender
DEVICE_PACKAGES := rssileds nvram -swconfig
IMAGE_SIZE := 7808k
ADDPATTERN_ID := mynet-rext
ADDPATTERN_VERSION := 1.00.01
IMAGE/sysupgrade.bin := append-rootfs | pad-rootfs | cybertan-trx | \
addpattern | append-metadata
SUPPORTED_DEVICES += mynet-rext
endef
TARGET_DEVICES += wd_mynet-wifi-rangeextender
define Device/winchannel_wb2000
SOC := ar9344
DEVICE_VENDOR := Winchannel
DEVICE_MODEL := WB2000
IMAGE_SIZE := 15872k
DEVICE_PACKAGES := kmod-i2c-gpio kmod-rtc-ds1307 kmod-usb2 \
kmod-usb-ledtrig-usbport
endef
TARGET_DEVICES += winchannel_wb2000
define Device/xiaomi_aiot-ac2350
SOC := qca9563
DEVICE_VENDOR := Xiaomi
DEVICE_MODEL := AIoT AC2350
DEVICE_PACKAGES := kmod-ath10k-ct ath10k-firmware-qca9984-ct
IMAGE_SIZE := 14336k
endef
TARGET_DEVICES += xiaomi_aiot-ac2350
define Device/xiaomi_mi-router-4q
SOC := qca9561
DEVICE_VENDOR := Xiaomi
DEVICE_MODEL := Mi Router 4Q
IMAGE_SIZE := 14336k
endef
TARGET_DEVICES += xiaomi_mi-router-4q
define Device/yuncore_a770
SOC := qca9531
DEVICE_VENDOR := YunCore
DEVICE_MODEL := A770
DEVICE_PACKAGES := kmod-ath10k-ct ath10k-firmware-qca9887-ct
IMAGE_SIZE := 16000k
IMAGES += tftp.bin
IMAGE/tftp.bin := $$(IMAGE/sysupgrade.bin) | yuncore-tftp-header-16m
endef
TARGET_DEVICES += yuncore_a770
define Device/yuncore_a782
SOC := qca9563
DEVICE_VENDOR := YunCore
DEVICE_MODEL := A782
DEVICE_PACKAGES := kmod-ath10k-ct ath10k-firmware-qca9888-ct
IMAGE_SIZE := 16000k
IMAGES += tftp.bin
IMAGE/tftp.bin := $$(IMAGE/sysupgrade.bin) | yuncore-tftp-header-16m
endef
TARGET_DEVICES += yuncore_a782
define Device/yuncore_a930
SOC := qca9533
DEVICE_VENDOR := YunCore
DEVICE_MODEL := A930
IMAGE_SIZE := 16000k
IMAGES += tftp.bin
IMAGE/tftp.bin := $$(IMAGE/sysupgrade.bin) | yuncore-tftp-header-16m
endef
TARGET_DEVICES += yuncore_a930
define Device/yuncore_xd3200
SOC := qca9563
DEVICE_VENDOR := YunCore
DEVICE_MODEL := XD3200
DEVICE_PACKAGES := kmod-ath10k-ct ath10k-firmware-qca988x-ct
IMAGE_SIZE := 16000k
IMAGES += tftp.bin
IMAGE/tftp.bin := $$(IMAGE/sysupgrade.bin) | yuncore-tftp-header-16m
endef
TARGET_DEVICES += yuncore_xd3200
define Device/yuncore_xd4200
SOC := qca9563
DEVICE_VENDOR := YunCore
DEVICE_MODEL := XD4200
DEVICE_PACKAGES := kmod-ath10k-ct ath10k-firmware-qca9888-ct
IMAGE_SIZE := 16000k
IMAGES += tftp.bin
IMAGE/tftp.bin := $$(IMAGE/sysupgrade.bin) | yuncore-tftp-header-16m
endef
TARGET_DEVICES += yuncore_xd4200
define Device/ziking_cpe46b
SOC := ar9330
DEVICE_VENDOR := ZiKing
DEVICE_MODEL := CPE46B
IMAGE_SIZE := 8000k
DEVICE_PACKAGES := kmod-i2c-gpio
endef
TARGET_DEVICES += ziking_cpe46b
define Device/zbtlink_zbt-wd323
SOC := ar9344
DEVICE_VENDOR := ZBT
DEVICE_MODEL := WD323
IMAGE_SIZE := 16000k
DEVICE_PACKAGES := kmod-usb2 kmod-i2c-gpio kmod-rtc-pcf8563 \
kmod-usb-serial-cp210x uqmi
endef
TARGET_DEVICES += zbtlink_zbt-wd323
define Device/zyxel_nwa11xx
$(Device/loader-okli-uimage)
SOC := ar9342
DEVICE_VENDOR := ZyXEL
LOADER_FLASH_OFFS := 0x050000
KERNEL := kernel-bin | append-dtb | lzma | uImage lzma -M 0x4f4b4c49
IMAGE_SIZE := 8192k
IMAGES += factory-$$$$(ZYXEL_MODEL_STRING).bin
IMAGE/factory-$$$$(ZYXEL_MODEL_STRING).bin := \
append-kernel | pad-to $$$$(BLOCKSIZE) | append-rootfs | \
pad-rootfs | pad-to 8192k | check-size | zyxel-tar-bz2 \
vmlinux_mi124_f1e mi124_f1e-jffs2 | append-md5sum-bin
endef
define Device/zyxel_nwa1100-nh
$(Device/zyxel_nwa11xx)
DEVICE_MODEL := NWA1100
DEVICE_VARIANT := NH
ZYXEL_MODEL_STRING := AASI
endef
TARGET_DEVICES += zyxel_nwa1100-nh
define Device/zyxel_nwa1121-ni
$(Device/zyxel_nwa11xx)
DEVICE_MODEL := NWA1121
DEVICE_VARIANT := NI
ZYXEL_MODEL_STRING := AABJ
endef
TARGET_DEVICES += zyxel_nwa1121-ni
define Device/zyxel_nwa1123-ac
$(Device/zyxel_nwa11xx)
DEVICE_MODEL := NWA1123
DEVICE_VARIANT := AC
ZYXEL_MODEL_STRING := AAOX
DEVICE_PACKAGES := kmod-ath10k-ct-smallbuffers \
ath10k-firmware-qca988x-ct
endef
TARGET_DEVICES += zyxel_nwa1123-ac
define Device/zyxel_nwa1123-ni
$(Device/zyxel_nwa11xx)
DEVICE_MODEL := NWA1123
DEVICE_VARIANT := NI
ZYXEL_MODEL_STRING := AAEO
endef
TARGET_DEVICES += zyxel_nwa1123-ni
define Device/zyxel_nbg6616
SOC := qca9557
DEVICE_VENDOR := ZyXEL
DEVICE_MODEL := NBG6616
DEVICE_PACKAGES := kmod-usb2 kmod-usb-ledtrig-usbport kmod-rtc-pcf8563 \
kmod-ath10k-ct ath10k-firmware-qca988x-ct
IMAGE_SIZE := 15232k
RAS_BOARD := NBG6616
RAS_ROOTFS_SIZE := 14464k
RAS_VERSION := "OpenWrt Linux-$(LINUX_VERSION)"
IMAGES += factory.bin
IMAGE/factory.bin := append-kernel | pad-to $$$$(BLOCKSIZE) | \
append-rootfs | pad-rootfs | pad-to 64k | check-size | zyxel-ras-image
SUPPORTED_DEVICES += nbg6616
endef
TARGET_DEVICES += zyxel_nbg6616
Reference in New Issue View Git Blame Copy Permalink