openwrt/target/linux/ramips/dts/mt7620a_dlink_dwr-118-a1.dts
Adrian Schmutzler d7a28e8ed2 ramips: mt7620: tidy up ethernet node in DTS files
This tidies up the ethernet node in mt7620 DTS files by:

- removing unnecessary status as it is not disabled
- reordering properties consistently
- adding empty lines to enhance readability

This should make comparison and reviewing new PRs based on C/P easier.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-05-17 18:28:03 +02:00

191 lines
2.9 KiB
Plaintext

// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
/dts-v1/;
#include "mt7620a.dtsi"
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/input/input.h>
/ {
compatible = "dlink,dwr-118-a1", "ralink,mt7620a-soc";
model = "D-Link DWR-118 A1";
aliases {
led-boot = &led_internet;
led-failsafe = &led_internet;
led-upgrade = &led_internet;
};
keys {
compatible = "gpio-keys";
wps {
label = "wps";
gpios = <&gpio0 12 GPIO_ACTIVE_LOW>;
linux,code = <KEY_WPS_BUTTON>;
};
reset {
label = "reset";
gpios = <&gpio0 13 GPIO_ACTIVE_LOW>;
linux,code = <KEY_RESTART>;
};
};
leds {
compatible = "gpio-leds";
wan {
label = "dwr-118-a1:green:wan";
gpios = <&gpio3 0 GPIO_ACTIVE_LOW>;
};
led_internet: internet {
label = "dwr-118-a1:green:internet";
gpios = <&gpio2 0 GPIO_ACTIVE_LOW>;
};
lan {
label = "dwr-118-a1:green:lan";
gpios = <&gpio2 1 GPIO_ACTIVE_LOW>;
};
wlan2g {
label = "dwr-118-a1:green:wlan2g";
gpios = <&gpio1 15 GPIO_ACTIVE_LOW>;
};
usb {
label = "dwr-118-a1:green:usb";
gpios = <&gpio0 11 GPIO_ACTIVE_LOW>;
trigger-sources = <&ohci_port1>, <&ehci_port1>;
linux,default-trigger = "usbport";
};
};
gpio_export {
compatible = "gpio-export";
#size-cells = <0>;
usb {
gpio-export,name = "usb";
gpio-export,output = <0>;
gpios = <&gpio1 14 GPIO_ACTIVE_LOW>;
};
};
};
&gpio1 {
status = "okay";
};
&gpio2 {
status = "okay";
};
&gpio3 {
status = "okay";
};
&spi0 {
status = "okay";
flash@0 {
compatible = "jedec,spi-nor";
reg = <0>;
spi-max-frequency = <80000000>;
partitions {
compatible = "fixed-partitions";
#address-cells = <1>;
#size-cells = <1>;
partition@0 {
label = "jboot";
reg = <0x0 0x10000>;
read-only;
};
partition@10000 {
compatible = "amit,jimage";
label = "firmware";
reg = <0x10000 0xfe0000>;
};
config: partition@ff0000 {
label = "config";
reg = <0xff0000 0x10000>;
read-only;
};
};
};
};
&ehci {
status = "okay";
};
&ohci {
status = "okay";
};
&state_default {
default {
groups = "ephy", "uartf", "spi refclk", "wled";
function = "gpio";
};
};
&pcie {
status = "okay";
};
&pcie0 {
wifi@0,0 {
reg = <0x0000 0 0 0 0>;
mtd-mac-address = <&config 0xe496>;
mtd-mac-address-increment = <(2)>;
mediatek,mtd-eeprom = <&config 0xe083>;
led {
led-sources = <0>;
led-active-low;
};
};
};
&ethernet {
pinctrl-names = "default";
pinctrl-0 = <&rgmii1_pins &rgmii2_pins &mdio_pins>;
port@4 {
status = "okay";
phy-handle = <&phy4>;
phy-mode = "rgmii";
};
port@5 {
status = "okay";
phy-handle = <&phy5>;
phy-mode = "rgmii";
};
mdio-bus {
status = "okay";
phy4: ethernet-phy@4 {
reg = <4>;
phy-mode = "rgmii-rxid";
};
phy5: ethernet-phy@5 {
reg = <5>;
phy-mode = "rgmii-rxid";
};
};
};
&gsw {
mediatek,port4 = "gmac";
};