mirror of
https://github.com/openwrt/openwrt.git
synced 2024-12-30 10:39:04 +00:00
3f8c5d5476
This commit adds support for the AVM Fritz!Box 4020 WiFi-router. SoC: Qualcomm Atheros QCA9561 (Dragonfly) 750MHz RAM: Winbond W971GG6KB-25 FLASH: Macronix MX25L12835F WiFi: QCA9561 b/g/n 3x3 450Mbit/s USB: 1x USB 2.0 IN: WPS button, WiFi button OUT: Power LED green, Internet LED green, WLAN LED green, LAN LED green, INFO LED green, INFO LED red UART: Header Next to Black metal shield Pinout is 3.3V - RX - TX - GND (Square Pad is 3.3V) The Serial setting is 115200-8-N-1. Tested and working: - Ethernet (LAN + WAN) - WiFi (correct MAC) - Installation via EVA bootloader - OpenWRT sysupgrade - Buttons - LEDs The USB port doesn't work. Both Root Hubs are detected as having 0 Ports: [ 3.670807] kmodloader: loading kernel modules from /etc/modules-boot.d/* [ 3.723267] usbcore: registered new interface driver usbfs [ 3.729058] usbcore: registered new interface driver hub [ 3.734616] usbcore: registered new device driver usb [ 3.744181] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 3.758357] SCSI subsystem initialized [ 3.766026] ehci-platform: EHCI generic platform driver [ 3.771548] ehci-platform ehci-platform.0: EHCI Host Controller [ 3.777708] ehci-platform ehci-platform.0: new USB bus registered, assigned bus number 1 [ 3.788169] ehci-platform ehci-platform.0: irq 48, io mem 0x1b000000 [ 3.816647] ehci-platform ehci-platform.0: USB 2.0 started, EHCI 0.00 [ 3.824001] hub 1-0:1.0: USB hub found [ 3.828219] hub 1-0:1.0: config failed, hub doesn't have any ports! (err -19) [ 3.835825] ehci-platform ehci-platform.1: EHCI Host Controller [ 3.842009] ehci-platform ehci-platform.1: new USB bus registered, assigned bus number 2 [ 3.852481] ehci-platform ehci-platform.1: irq 49, io mem 0x1b400000 [ 3.886631] ehci-platform ehci-platform.1: USB 2.0 started, EHCI 0.00 [ 3.894011] hub 2-0:1.0: USB hub found [ 3.898190] hub 2-0:1.0: config failed, hub doesn't have any ports! (err -19) [ 3.908928] usbcore: registered new interface driver usb-storage [ 3.915634] kmodloader: done loading kernel modules from /etc/modules-boot.d/* A few words about the shift-register: AVM used a trick to control the shift-register for the LEDs with only 2 pins, SERCLK and MOSI. Q7S, normally used for daisy-chaining multiple shift-registers, pulls the latch, moving the shift register-state to the storage register. It also pulls down MR (normally pulled up) to clear the storage register, so the latch gets released and will not be pulled by the remaining bits in the shift-register. Shift register is all-zero after this. For that we need to make sure output 7 is set to high on driver probe. We accomplish this by using gpio-hogging. Installation via EVA: In the first seconds after Power is connected, the bootloader will listen for FTP connections on 169.254.157.1 (Might also be 192.168.178.1). Firmware can be uploaded like following: ftp> quote USER adam2 ftp> quote PASS adam2 ftp> binary ftp> debug ftp> passive ftp> quote MEDIA FLSH ftp> put openwrt-sysupgrade.bin mtd1 Note that this procedure might take up to two minutes. After transfer is complete you need to powercycle the device to boot OpenWRT. Signed-off-by: David Bauer <mail@david-bauer.net>
181 lines
3.8 KiB
Bash
181 lines
3.8 KiB
Bash
#!/bin/sh
|
|
|
|
[ -e /lib/firmware/$FIRMWARE ] && exit 0
|
|
|
|
. /lib/functions.sh
|
|
. /lib/functions/system.sh
|
|
|
|
ath9k_eeprom_die() {
|
|
echo "ath9k eeprom: " "$*"
|
|
exit 1
|
|
}
|
|
|
|
ath9k_eeprom_extract() {
|
|
local part=$1
|
|
local offset=$2
|
|
local count=$3
|
|
local mtd
|
|
|
|
mtd=$(find_mtd_chardev $part)
|
|
[ -n "$mtd" ] || \
|
|
ath9k_eeprom_die "no mtd device found for partition $part"
|
|
|
|
dd if=$mtd of=/lib/firmware/$FIRMWARE bs=1 skip=$offset count=$count 2>/dev/null || \
|
|
ath9k_eeprom_die "failed to extract from $mtd"
|
|
}
|
|
|
|
ath9k_eeprom_extract_reverse() {
|
|
local part=$1
|
|
local offset=$2
|
|
local count=$3
|
|
local mtd
|
|
local reversed
|
|
local caldata
|
|
|
|
mtd=$(find_mtd_chardev "$part")
|
|
reversed=$(hexdump -v -s $offset -n $count -e '/1 "%02x "' $mtd)
|
|
|
|
for byte in $reversed; do
|
|
caldata="\x${byte}${caldata}"
|
|
done
|
|
|
|
printf "%b" "$caldata" > /lib/firmware/$FIRMWARE
|
|
}
|
|
|
|
xor() {
|
|
local val
|
|
local ret="0x$1"
|
|
local retlen=${#1}
|
|
|
|
shift
|
|
while [ -n "$1" ]; do
|
|
val="0x$1"
|
|
ret=$((ret ^ val))
|
|
shift
|
|
done
|
|
|
|
printf "%0${retlen}x" "$ret"
|
|
}
|
|
|
|
ath9k_patch_fw_mac() {
|
|
local mac=$1
|
|
local mac_offset=$2
|
|
local chksum_offset=$3
|
|
local xor_mac
|
|
local xor_fw_mac
|
|
local xor_fw_chksum
|
|
|
|
[ -z "$mac" -o -z "$mac_offset" ] && return
|
|
|
|
[ -n "$chksum_offset" ] && {
|
|
xor_mac=${mac//:/}
|
|
xor_mac="${xor_mac:0:4} ${xor_mac:4:4} ${xor_mac:8:4}"
|
|
|
|
xor_fw_mac=$(hexdump -v -n 6 -s $mac_offset -e '/1 "%02x"' /lib/firmware/$FIRMWARE)
|
|
xor_fw_mac="${xor_fw_mac:0:4} ${xor_fw_mac:4:4} ${xor_fw_mac:8:4}"
|
|
|
|
xor_fw_chksum=$(hexdump -v -n 2 -s $chksum_offset -e '/1 "%02x"' /lib/firmware/$FIRMWARE)
|
|
xor_fw_chksum=$(xor $xor_fw_chksum $xor_fw_mac $xor_mac)
|
|
|
|
printf "%b" "\x${xor_fw_chksum:0:2}\x${xor_fw_chksum:2:2}" | \
|
|
dd of=/lib/firmware/$FIRMWARE conv=notrunc bs=1 seek=$chksum_offset count=2
|
|
}
|
|
|
|
macaddr_2bin $mac | dd of=/lib/firmware/$FIRMWARE conv=notrunc bs=1 seek=$mac_offset count=6
|
|
}
|
|
|
|
ath9k_patch_fw_mac_crc() {
|
|
local mac=$1
|
|
local mac_offset=$2
|
|
local chksum_offset=$((mac_offset - 10))
|
|
|
|
ath9k_patch_fw_mac "${mac}" "${mac_offset}" "${chksum_offset}"
|
|
}
|
|
|
|
board=$(board_name)
|
|
|
|
case "$FIRMWARE" in
|
|
"ath9k-eeprom-ahb-18100000.wmac.bin")
|
|
case $board in
|
|
avm,fritz4020)
|
|
ath9k_eeprom_extract_reverse "urlader" 5441 1088
|
|
;;
|
|
iodata,wn-ac1167dgr|\
|
|
iodata,wn-ac1600dgr2)
|
|
ath9k_eeprom_extract "art" 4096 1088
|
|
ath9k_patch_fw_mac $(mtd_get_mac_ascii u-boot-env ethaddr) 2
|
|
;;
|
|
*)
|
|
ath9k_eeprom_die "board $board is not supported yet"
|
|
;;
|
|
esac
|
|
;;
|
|
"ath9k-eeprom-pci-0000:00:00.0.bin")
|
|
case $board in
|
|
avm,fritz300e)
|
|
ath9k_eeprom_extract_reverse "urloader" 5441 1088
|
|
;;
|
|
buffalo,whr-g301n|\
|
|
tplink,tl-wr841-v5|\
|
|
tplink,tl-wr941-v4)
|
|
ath9k_eeprom_extract "art" 4096 3768
|
|
;;
|
|
ocedo,raccoon|\
|
|
tplink,tl-wdr3600|\
|
|
tplink,tl-wdr4300|\
|
|
tplink,tl-wdr4900-v2)
|
|
ath9k_eeprom_extract "art" 20480 1088
|
|
;;
|
|
netgear,wnr612-v2|\
|
|
on,n150r|\
|
|
pcs,cap324|\
|
|
tplink,tl-mr3220-v1|\
|
|
tplink,tl-mr3420-v1|\
|
|
tplink,tl-wr2543-v1|\
|
|
tplink,tl-wr740n-v1|\
|
|
tplink,tl-wr740n-v3|\
|
|
tplink,tl-wr741-v1|\
|
|
tplink,tl-wr743nd-v1|\
|
|
tplink,tl-wr841-v7|\
|
|
ubnt,unifi)
|
|
ath9k_eeprom_extract "art" 4096 2048
|
|
;;
|
|
*)
|
|
ath9k_eeprom_die "board $board is not supported yet"
|
|
;;
|
|
esac
|
|
;;
|
|
"ath9k-eeprom-pci-0000:00:11.0.bin")
|
|
case $board in
|
|
dlink,dir-825-b1)
|
|
ath9k_eeprom_extract "caldata" 4096 3768
|
|
ath9k_patch_fw_mac_crc $(mtd_get_mac_text "caldata" 65440) 524
|
|
;;
|
|
netgear,wndr3700|\
|
|
netgear,wndr3700v2|\
|
|
netgear,wndr3800)
|
|
ath9k_eeprom_extract "art" 4096 3768
|
|
;;
|
|
*)
|
|
ath9k_eeprom_die "board $board is not supported yet"
|
|
;;
|
|
esac
|
|
;;
|
|
"ath9k-eeprom-pci-0000:00:12.0.bin")
|
|
case $board in
|
|
dlink,dir-825-b1)
|
|
ath9k_eeprom_extract "caldata" 20480 3768
|
|
ath9k_patch_fw_mac_crc $(macaddr_add $(mtd_get_mac_text "caldata" 65460) 1) 524
|
|
;;
|
|
netgear,wndr3700|\
|
|
netgear,wndr3700v2|\
|
|
netgear,wndr3800)
|
|
ath9k_eeprom_extract "art" 20480 3768
|
|
;;
|
|
*)
|
|
ath9k_eeprom_die "board $board is not supported yet"
|
|
;;
|
|
esac
|
|
;;
|
|
esac
|