ExternalVendorCode/openwrt
1
0
Fork 0
mirror of https://github.com/openwrt/openwrt.git synced 2024-12-28 17:48:58 +00:00
Code Issues Actions 7 Packages Projects Releases Wiki Activity
2e064182bf
openwrt/target/linux/mediatek/image/filogic.mk
Leon M. Busch-George 74df6ce9db mediatek: filogic: add support for Cudy M3000 v1 
Hardware:
  SoC:     MT7981b
  RAM:     256 MB
  Flash:   128 MB SPI NAND
  Ethernet:
    1x 2.5Gbps (rtl8221b)
    1x 1Gbps (integrated phy)
  WiFi:    2x2 MT7981
  Buttons: Reset, WPS
  LED:     1x multicolor

Solder on UART:
  - remove rubber ring on the bottom
  - remove screws
  - pull up the cylinder, maybe help by push on an ethernet socket with a screwdriver
  - remove the (3) screws holding the board in the frame
  - remove the board from the frame to get to the screws for the silver, flat heat shield
  - remove the (3) screws holding the heat shield
  - solder UART pins to the back of the board
    - make sure to have the pins point out on side with the black, finned heat spread
    - the markings for the pins are going to be below the silver heat shield
    - Vcc is not needed

If you don't intend on using the UART outside of the installation process, you might not
want to solder:

  - carefully scrape off the thin layer of epoxy on the holes (not the copper)
  - place your pin header with the UART attached in the holes
  - the pins, starting with the one closest to the socket:
    - Vcc (not required)
    - GND
    - RX
    - TX
  - either wedge the header or hold it with your fingers so that the pins stay in contact with the board

Installation (UART):
  - attach an Ethernet cable to the 1Gbps port (black) on the router
  - hold the reset button while powering the router
  - press CTRL-C or wait for the timeout to get to the U-Boot prompt
  - prepare a TFTP server on the network to supply ..-initramfs-kernel.bin
  - use 'tftpboot' in the U-Boot shell to pull the image
  - boot the image using 'bootm'
  - push the ..-sysupgrade to the router using your preferred method
  - perform the upgrade with 'sysupgrade -n'

There is a recovery mechanism that involves fetching a file called 'recovery.bin' but that is not understood yet.

Signed-off-by: Leon M. Busch-George <leon@georgemail.eu>
(cherry picked from commit 20e4a18feb)
2024-07-15 16:12:33 +02:00

1156 lines
41 KiB
Makefile
Raw Blame History

DTS_DIR := $(DTS_DIR)/mediatek
define Image/Prepare
# For UBI we want only one extra block
rm -f $(KDIR)/ubi_mark
echo -ne '\xde\xad\xc0\xde' > $(KDIR)/ubi_mark
endef
define Build/mt7981-bl2
cat $(STAGING_DIR_IMAGE)/mt7981-$1-bl2.img >> $@
endef
define Build/mt7981-bl31-uboot
cat $(STAGING_DIR_IMAGE)/mt7981_$1-u-boot.fip >> $@
endef
define Build/mt7986-bl2
cat $(STAGING_DIR_IMAGE)/mt7986-$1-bl2.img >> $@
endef
define Build/mt7986-bl31-uboot
cat $(STAGING_DIR_IMAGE)/mt7986_$1-u-boot.fip >> $@
endef
define Build/mt7988-bl2
cat $(STAGING_DIR_IMAGE)/mt7988-$1-bl2.img >> $@
endef
define Build/mt7988-bl31-uboot
cat $(STAGING_DIR_IMAGE)/mt7988_$1-u-boot.fip >> $@
endef
define Build/mt798x-gpt
cp $@ $@.tmp 2>/dev/null || true
ptgen -g -o $@.tmp -a 1 -l 1024 \
$(if $(findstring sdmmc,$1), \
-H \
-t 0x83 -N bl2 -r -p 4079k@17k \
) \
-t 0x83 -N ubootenv -r -p 512k@4M \
-t 0x83 -N factory -r -p 2M@4608k \
-t 0xef -N fip -r -p 4M@6656k \
-N recovery -r -p 32M@12M \
$(if $(findstring sdmmc,$1), \
-N install -r -p 20M@44M \
-t 0x2e -N production -p $(CONFIG_TARGET_ROOTFS_PARTSIZE)M@64M \
) \
$(if $(findstring emmc,$1), \
-t 0x2e -N production -p $(CONFIG_TARGET_ROOTFS_PARTSIZE)M@64M \
)
cat $@.tmp >> $@
rm $@.tmp
endef
metadata_gl_json = \
'{ $(if $(IMAGE_METADATA),$(IMAGE_METADATA)$(comma)) \
"metadata_version": "1.1", \
"compat_version": "$(call json_quote,$(compat_version))", \
$(if $(DEVICE_COMPAT_MESSAGE),"compat_message": "$(call json_quote,$(DEVICE_COMPAT_MESSAGE))"$(comma)) \
$(if $(filter-out 1.0,$(compat_version)),"new_supported_devices": \
[$(call metadata_devices,$(SUPPORTED_DEVICES))]$(comma) \
"supported_devices": ["$(call json_quote,$(legacy_supported_message))"]$(comma)) \
$(if $(filter 1.0,$(compat_version)),"supported_devices":[$(call metadata_devices,$(SUPPORTED_DEVICES))]$(comma)) \
"version": { \
"release": "$(call json_quote,$(VERSION_NUMBER))", \
"date": "$(shell TZ='Asia/Chongqing' date '+%Y%m%d%H%M%S')", \
"dist": "$(call json_quote,$(VERSION_DIST))", \
"version": "$(call json_quote,$(VERSION_NUMBER))", \
"revision": "$(call json_quote,$(REVISION))", \
"target": "$(call json_quote,$(TARGETID))", \
"board": "$(call json_quote,$(if $(BOARD_NAME),$(BOARD_NAME),$(DEVICE_NAME)))" \
} \
}'
define Build/append-gl-metadata
$(if $(SUPPORTED_DEVICES),-echo $(call metadata_gl_json,$(SUPPORTED_DEVICES)) | fwtool -I - $@)
sha256sum "$@" | cut -d" " -f1 > "$@.sha256sum"
[ ! -s "$(BUILD_KEY)" -o ! -s "$(BUILD_KEY).ucert" -o ! -s "$@" ] || { \
cp "$(BUILD_KEY).ucert" "$@.ucert" ;\
usign -S -m "$@" -s "$(BUILD_KEY)" -x "$@.sig" ;\
ucert -A -c "$@.ucert" -x "$@.sig" ;\
fwtool -S "$@.ucert" "$@" ;\
}
endef
define Build/zyxel-nwa-fit-filogic
$(TOPDIR)/scripts/mkits-zyxel-fit-filogic.sh \
$@.its $@ "80 e1 ff ff ff ff ff ff ff ff"
PATH=$(LINUX_DIR)/scripts/dtc:$(PATH) mkimage -f $@.its $@.new
@mv $@.new $@
endef
define Build/cetron-header
$(eval magic=$(word 1,$(1)))
$(eval model=$(word 2,$(1)))
( \
dd if=/dev/zero bs=856 count=1 2>/dev/null; \
printf "$(model)," | dd bs=128 count=1 conv=sync 2>/dev/null; \
md5sum $@ | cut -f1 -d" " | dd bs=32 count=1 2>/dev/null; \
printf "$(magic)" | dd bs=4 count=1 conv=sync 2>/dev/null; \
cat $@; \
) > $@.tmp
fw_crc=$$(gzip -c $@.tmp | tail -c 8 | od -An -N4 -tx4 --endian little | tr -d ' \n'); \
printf "$$(echo $$fw_crc | sed 's/../\\x&/g')" | cat - $@.tmp > $@
rm $@.tmp
endef
define Device/acelink_ew-7886cax
DEVICE_VENDOR := Acelink
DEVICE_MODEL := EW-7886CAX
DEVICE_DTS := mt7986a-acelink-ew-7886cax
DEVICE_DTS_DIR := ../dts
DEVICE_PACKAGES := kmod-mt7986-firmware mt7986-wo-firmware
UBINIZE_OPTS := -E 5
BLOCKSIZE := 128k
PAGESIZE := 2048
IMAGE_SIZE := 65536k
KERNEL_IN_UBI := 1
IMAGES += factory.bin
IMAGE/factory.bin := append-ubi | check-size $$$$(IMAGE_SIZE)
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
endef
TARGET_DEVICES += acelink_ew-7886cax
define Device/acer_predator-w6
DEVICE_VENDOR := Acer
DEVICE_MODEL := Predator W6
DEVICE_DTS := mt7986a-acer-predator-w6
DEVICE_DTS_DIR := ../dts
DEVICE_DTS_LOADADDR := 0x47000000
DEVICE_PACKAGES := kmod-usb3 kmod-mt7986-firmware kmod-mt7916-firmware mt7986-wo-firmware e2fsprogs f2fsck mkf2fs
IMAGES := sysupgrade.bin
KERNEL := kernel-bin | lzma | fit lzma $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb
KERNEL_INITRAMFS := kernel-bin | lzma | \
fit lzma $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb with-initrd | pad-to 64k
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
endef
TARGET_DEVICES += acer_predator-w6
define Device/adtran_smartrg
DEVICE_VENDOR := Adtran
DEVICE_DTS_DIR := ../dts
DEVICE_PACKAGES := e2fsprogs f2fsck mkf2fs kmod-hwmon-pwmfan \
kmod-mt7986-firmware mt7986-wo-firmware
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
endef
define Device/smartrg_sdg-8612
$(call Device/adtran_smartrg)
DEVICE_MODEL := SDG-8612
DEVICE_DTS := mt7986a-smartrg-SDG-8612
endef
TARGET_DEVICES += smartrg_sdg-8612
define Device/smartrg_sdg-8614
$(call Device/adtran_smartrg)
DEVICE_MODEL := SDG-8614
DEVICE_DTS := mt7986a-smartrg-SDG-8614
endef
TARGET_DEVICES += smartrg_sdg-8614
define Device/smartrg_sdg-8622
$(call Device/adtran_smartrg)
DEVICE_MODEL := SDG-8622
DEVICE_DTS := mt7986a-smartrg-SDG-8622
DEVICE_PACKAGES += kmod-mt7915-firmware
endef
TARGET_DEVICES += smartrg_sdg-8622
define Device/smartrg_sdg-8632
$(call Device/adtran_smartrg)
DEVICE_MODEL := SDG-8632
DEVICE_DTS := mt7986a-smartrg-SDG-8632
DEVICE_PACKAGES += kmod-mt7915-firmware
endef
TARGET_DEVICES += smartrg_sdg-8632
define Device/asus_rt-ax59u
DEVICE_VENDOR := ASUS
DEVICE_MODEL := RT-AX59U
DEVICE_DTS := mt7986a-asus-rt-ax59u
DEVICE_DTS_DIR := ../dts
DEVICE_PACKAGES := kmod-usb3 kmod-mt7986-firmware mt7986-wo-firmware
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
endef
TARGET_DEVICES += asus_rt-ax59u
define Device/asus_tuf-ax4200
DEVICE_VENDOR := ASUS
DEVICE_MODEL := TUF-AX4200
DEVICE_DTS := mt7986a-asus-tuf-ax4200
DEVICE_DTS_DIR := ../dts
DEVICE_DTS_LOADADDR := 0x47000000
DEVICE_PACKAGES := kmod-usb3 kmod-mt7986-firmware mt7986-wo-firmware
IMAGES := sysupgrade.bin
KERNEL := kernel-bin | lzma | \
fit lzma $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb
KERNEL_INITRAMFS := kernel-bin | lzma | \
fit lzma $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb with-initrd | pad-to 64k
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
endef
TARGET_DEVICES += asus_tuf-ax4200
define Device/asus_tuf-ax6000
DEVICE_VENDOR := ASUS
DEVICE_MODEL := TUF-AX6000
DEVICE_DTS := mt7986a-asus-tuf-ax6000
DEVICE_DTS_DIR := ../dts
DEVICE_DTS_LOADADDR := 0x47000000
DEVICE_PACKAGES := kmod-usb3 kmod-mt7986-firmware mt7986-wo-firmware
IMAGES := sysupgrade.bin
KERNEL := kernel-bin | lzma | \
fit lzma $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb
KERNEL_INITRAMFS := kernel-bin | lzma | \
fit lzma $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb with-initrd | pad-to 64k
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
endef
TARGET_DEVICES += asus_tuf-ax6000
define Device/bananapi_bpi-r3
DEVICE_VENDOR := Bananapi
DEVICE_MODEL := BPi-R3
DEVICE_DTS := mt7986a-bananapi-bpi-r3
DEVICE_DTS_CONFIG := config-mt7986a-bananapi-bpi-r3
DEVICE_DTS_OVERLAY:= mt7986a-bananapi-bpi-r3-emmc mt7986a-bananapi-bpi-r3-nand mt7986a-bananapi-bpi-r3-nor mt7986a-bananapi-bpi-r3-sd
DEVICE_DTS_DIR := $(DTS_DIR)/
DEVICE_DTS_LOADADDR := 0x43f00000
DEVICE_PACKAGES := kmod-hwmon-pwmfan kmod-i2c-gpio kmod-mt7986-firmware kmod-sfp kmod-usb3 e2fsprogs f2fsck mkf2fs mt7986-wo-firmware
IMAGES := sysupgrade.itb
KERNEL_LOADADDR := 0x44000000
KERNEL_INITRAMFS_SUFFIX := -recovery.itb
ARTIFACTS := \
emmc-preloader.bin emmc-bl31-uboot.fip \
nor-preloader.bin nor-bl31-uboot.fip \
sdcard.img.gz \
snand-preloader.bin snand-bl31-uboot.fip
ARTIFACT/emmc-preloader.bin := mt7986-bl2 emmc-ddr4
ARTIFACT/emmc-bl31-uboot.fip := mt7986-bl31-uboot bananapi_bpi-r3-emmc
ARTIFACT/nor-preloader.bin := mt7986-bl2 nor-ddr4
ARTIFACT/nor-bl31-uboot.fip := mt7986-bl31-uboot bananapi_bpi-r3-nor
ARTIFACT/snand-preloader.bin := mt7986-bl2 spim-nand-ddr4
ARTIFACT/snand-bl31-uboot.fip := mt7986-bl31-uboot bananapi_bpi-r3-snand
ARTIFACT/sdcard.img.gz := mt798x-gpt sdmmc |\
pad-to 17k | mt7986-bl2 sdmmc-ddr4 |\
pad-to 6656k | mt7986-bl31-uboot bananapi_bpi-r3-sdmmc |\
$(if $(CONFIG_TARGET_ROOTFS_INITRAMFS),\
pad-to 12M | append-image-stage initramfs-recovery.itb | check-size 44m |\
) \
pad-to 44M | mt7986-bl2 spim-nand-ddr4 |\
pad-to 45M | mt7986-bl31-uboot bananapi_bpi-r3-snand |\
pad-to 49M | mt7986-bl2 nor-ddr4 |\
pad-to 50M | mt7986-bl31-uboot bananapi_bpi-r3-nor |\
pad-to 51M | mt7986-bl2 emmc-ddr4 |\
pad-to 52M | mt7986-bl31-uboot bananapi_bpi-r3-emmc |\
pad-to 56M | mt798x-gpt emmc |\
$(if $(CONFIG_TARGET_ROOTFS_SQUASHFS),\
pad-to 64M | append-image squashfs-sysupgrade.itb | check-size |\
) \
gzip
ifeq ($(DUMP),)
IMAGE_SIZE := $$(shell expr 64 + $$(CONFIG_TARGET_ROOTFS_PARTSIZE))m
endif
KERNEL := kernel-bin | gzip
KERNEL_INITRAMFS := kernel-bin | lzma | \
fit lzma $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb with-initrd | pad-to 64k
IMAGE/sysupgrade.itb := append-kernel | fit gzip $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb external-static-with-rootfs | pad-rootfs | append-metadata
DEVICE_DTC_FLAGS := --pad 4096
DEVICE_COMPAT_VERSION := 1.1
DEVICE_COMPAT_MESSAGE := Device tree overlay mechanism needs bootloader update
endef
TARGET_DEVICES += bananapi_bpi-r3
define Device/cetron_ct3003
DEVICE_VENDOR := Cetron
DEVICE_MODEL := CT3003
DEVICE_DTS := mt7981b-cetron-ct3003
DEVICE_DTS_DIR := ../dts
SUPPORTED_DEVICES += mediatek,mt7981-spim-snand-rfb
DEVICE_PACKAGES := kmod-mt7981-firmware mt7981-wo-firmware
UBINIZE_OPTS := -E 5
BLOCKSIZE := 128k
PAGESIZE := 2048
KERNEL_IN_UBI := 1
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
IMAGES += factory.bin
IMAGE/factory.bin := $$(IMAGE/sysupgrade.bin) | cetron-header rd30 CT3003
endef
TARGET_DEVICES += cetron_ct3003
define Device/cmcc_rax3000m
DEVICE_VENDOR := CMCC
DEVICE_MODEL := RAX3000M
DEVICE_DTS := mt7981b-cmcc-rax3000m
DEVICE_DTS_OVERLAY := mt7981b-cmcc-rax3000m-emmc mt7981b-cmcc-rax3000m-nand
DEVICE_DTS_DIR := ../dts
DEVICE_DTC_FLAGS := --pad 4096
DEVICE_DTS_LOADADDR := 0x43f00000
DEVICE_PACKAGES := kmod-mt7981-firmware mt7981-wo-firmware kmod-usb3 \
e2fsprogs f2fsck mkf2fs
KERNEL_LOADADDR := 0x44000000
KERNEL := kernel-bin | gzip
KERNEL_INITRAMFS := kernel-bin | lzma | \
fit lzma $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb with-initrd | pad-to 64k
KERNEL_INITRAMFS_SUFFIX := -recovery.itb
KERNEL_IN_UBI := 1
UBOOTENV_IN_UBI := 1
IMAGES := sysupgrade.itb
IMAGE_SIZE := $$(shell expr 64 + $$(CONFIG_TARGET_ROOTFS_PARTSIZE))m
IMAGE/sysupgrade.itb := append-kernel | \
fit gzip $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb external-static-with-rootfs | \
pad-rootfs | append-metadata
ARTIFACTS := \
emmc-gpt.bin emmc-preloader.bin emmc-bl31-uboot.fip \
nand-preloader.bin nand-bl31-uboot.fip
ARTIFACT/emmc-gpt.bin := mt798x-gpt emmc
ARTIFACT/emmc-preloader.bin := mt7981-bl2 emmc-ddr4
ARTIFACT/emmc-bl31-uboot.fip := mt7981-bl31-uboot cmcc_rax3000m-emmc
ARTIFACT/nand-preloader.bin := mt7981-bl2 spim-nand-ddr4
ARTIFACT/nand-bl31-uboot.fip := mt7981-bl31-uboot cmcc_rax3000m-nand
endef
TARGET_DEVICES += cmcc_rax3000m
define Device/comfast_cf-e393ax
DEVICE_VENDOR := Comfast
DEVICE_MODEL := CF-E393AX
DEVICE_DTS := mt7981a-comfast-cf-e393ax
DEVICE_DTS_DIR := ../dts
DEVICE_DTC_FLAGS := --pad 4096
DEVICE_DTS_LOADADDR := 0x43f00000
DEVICE_PACKAGES := kmod-mt7981-firmware mt7981-wo-firmware
KERNEL_LOADADDR := 0x44000000
KERNEL = kernel-bin | lzma | \
fit lzma $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb
KERNEL_INITRAMFS = kernel-bin | lzma | \
fit lzma $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb with-initrd
UBINIZE_OPTS := -E 5
BLOCKSIZE := 128k
PAGESIZE := 2048
IMAGE_SIZE := 65536k
KERNEL_IN_UBI := 1
IMAGES := sysupgrade.bin factory.bin
IMAGE/factory.bin := append-ubi | check-size $$$$(IMAGE_SIZE)
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
endef
TARGET_DEVICES += comfast_cf-e393ax
define Device/confiabits_mt7981
DEVICE_VENDOR := Confiabits
DEVICE_MODEL := MT7981
DEVICE_DTS := mt7981b-confiabits-mt7981
DEVICE_DTS_DIR := ../dts
SUPPORTED_DEVICES += mediatek,mt7981-spim-snand-2500wan-gmac2-rfb
UBINIZE_OPTS := -E 5
BLOCKSIZE := 128k
PAGESIZE := 2048
IMAGE_SIZE := 65536k
KERNEL_IN_UBI := 1
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
DEVICE_PACKAGES := kmod-usb3 kmod-mt7981-firmware mt7981-wo-firmware
endef
TARGET_DEVICES += confiabits_mt7981
define Device/cudy_m3000-v1
DEVICE_VENDOR := Cudy
DEVICE_MODEL := M3000
DEVICE_VARIANT := v1
DEVICE_DTS := mt7981b-cudy-m3000-v1
DEVICE_DTS_DIR := ../dts
SUPPORTED_DEVICES += R37
DEVICE_DTS_LOADADDR := 0x44000000
BLOCKSIZE := 128k
PAGESIZE := 2048
IMAGE_SIZE := 65536k
KERNEL_IN_UBI := 1
KERNEL := kernel-bin | lzma | \
fit lzma $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb
KERNEL_INITRAMFS := kernel-bin | lzma | \
fit lzma $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb with-initrd | pad-to 64k
IMAGES := sysupgrade.bin
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
DEVICE_PACKAGES := kmod-mt7981-firmware mt7981-wo-firmware
endef
TARGET_DEVICES += cudy_m3000-v1
define Device/cudy_re3000-v1
DEVICE_VENDOR := Cudy
DEVICE_MODEL := RE3000
DEVICE_VARIANT := v1
DEVICE_DTS := mt7981b-cudy-re3000-v1
DEVICE_DTS_DIR := ../dts
DEVICE_DTS_LOADADDR := 0x47000000
IMAGES := sysupgrade.bin
IMAGE_SIZE := 15424k
SUPPORTED_DEVICES += R36
KERNEL := kernel-bin | lzma | \
fit lzma $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb
KERNEL_INITRAMFS := kernel-bin | lzma | \
fit lzma $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb with-initrd | pad-to 64k
IMAGE/sysupgrade.bin := append-kernel | pad-to 128k | append-rootfs | pad-rootfs | check-size | append-metadata
DEVICE_PACKAGES := kmod-mt7981-firmware mt7981-wo-firmware
endef
TARGET_DEVICES += cudy_re3000-v1
define Device/cudy_tr3000-v1
DEVICE_VENDOR := Cudy
DEVICE_MODEL := TR3000
DEVICE_VARIANT := v1
DEVICE_DTS := mt7981b-cudy-tr3000-v1
DEVICE_DTS_DIR := ../dts
SUPPORTED_DEVICES += R47
UBINIZE_OPTS := -E 5
BLOCKSIZE := 128k
PAGESIZE := 2048
IMAGE_SIZE := 65536k
KERNEL_IN_UBI := 1
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
DEVICE_PACKAGES := kmod-usb3 kmod-mt7981-firmware mt7981-wo-firmware
endef
TARGET_DEVICES += cudy_tr3000-v1
define Device/cudy_wr3000-v1
DEVICE_VENDOR := Cudy
DEVICE_MODEL := WR3000
DEVICE_VARIANT := v1
DEVICE_DTS := mt7981b-cudy-wr3000-v1
DEVICE_DTS_DIR := ../dts
DEVICE_DTS_LOADADDR := 0x47000000
IMAGES := sysupgrade.bin
IMAGE_SIZE := 15424k
SUPPORTED_DEVICES += R31
KERNEL := kernel-bin | lzma | \
fit lzma $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb
KERNEL_INITRAMFS := kernel-bin | lzma | \
fit lzma $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb with-initrd | pad-to 64k
IMAGE/sysupgrade.bin := append-kernel | pad-to 128k | append-rootfs | pad-rootfs | check-size | append-metadata
DEVICE_PACKAGES := kmod-mt7981-firmware mt7981-wo-firmware
endef
TARGET_DEVICES += cudy_wr3000-v1
define Device/dlink_aquila-pro-ai-m30-a1
DEVICE_VENDOR := D-Link
DEVICE_MODEL := AQUILA PRO AI M30
DEVICE_VARIANT := A1
DEVICE_DTS := mt7981b-dlink-aquila-pro-ai-m30-a1
DEVICE_DTS_DIR := ../dts
DEVICE_PACKAGES := kmod-leds-gca230718 kmod-mt7981-firmware mt7981-wo-firmware
KERNEL_IN_UBI := 1
IMAGES += recovery.bin
IMAGE_SIZE := 51200k
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
IMAGE/recovery.bin := sysupgrade-tar | pad-to $$(IMAGE_SIZE) | dlink-ai-recovery-header DLK6E6110001 \x6A\x28\xEE\x0B \x00\x00\x2C\x00 \x00\x00\x20\x03 \x61\x6E
endef
TARGET_DEVICES += dlink_aquila-pro-ai-m30-a1
define Device/glinet_gl-mt3000
DEVICE_VENDOR := GL.iNet
DEVICE_MODEL := GL-MT3000
DEVICE_DTS := mt7981b-glinet-gl-mt3000
DEVICE_DTS_DIR := ../dts
SUPPORTED_DEVICES += glinet,mt3000-snand
DEVICE_PACKAGES := kmod-mt7981-firmware mt7981-wo-firmware kmod-hwmon-pwmfan kmod-usb3
UBINIZE_OPTS := -E 5
BLOCKSIZE := 128k
PAGESIZE := 2048
IMAGE_SIZE := 246272k
KERNEL_IN_UBI := 1
IMAGE/sysupgrade.bin := sysupgrade-tar | append-gl-metadata
endef
TARGET_DEVICES += glinet_gl-mt3000
define Device/glinet_gl-mt6000
DEVICE_VENDOR := GL.iNet
DEVICE_MODEL := GL-MT6000
DEVICE_DTS := mt7986a-glinet-gl-mt6000
DEVICE_DTS_DIR := ../dts
DEVICE_PACKAGES := e2fsprogs f2fsck mkf2fs kmod-usb3 kmod-mt7986-firmware mt7986-wo-firmware
IMAGES += factory.bin
IMAGE/factory.bin := append-kernel | pad-to 32M | append-rootfs
IMAGE/sysupgrade.bin := sysupgrade-tar | append-gl-metadata
ARTIFACTS := preloader.bin bl31-uboot.fip
ARTIFACT/preloader.bin := mt7986-bl2 emmc-ddr4
ARTIFACT/bl31-uboot.fip := mt7986-bl31-uboot glinet_gl-mt6000
endef
TARGET_DEVICES += glinet_gl-mt6000
define Device/h3c_magic-nx30-pro
DEVICE_VENDOR := H3C
DEVICE_MODEL := Magic NX30 Pro
DEVICE_DTS := mt7981b-h3c-magic-nx30-pro
DEVICE_DTS_DIR := ../dts
UBINIZE_OPTS := -E 5
BLOCKSIZE := 128k
PAGESIZE := 2048
KERNEL_IN_UBI := 1
UBOOTENV_IN_UBI := 1
IMAGE_SIZE := 65536k
IMAGES := sysupgrade.itb
KERNEL_INITRAMFS_SUFFIX := -recovery.itb
KERNEL := kernel-bin | gzip
KERNEL_INITRAMFS := kernel-bin | lzma | \
fit lzma $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb with-initrd | pad-to 64k
IMAGE/sysupgrade.itb := append-kernel | \
fit gzip $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb external-static-with-rootfs | append-metadata
DEVICE_PACKAGES := kmod-mt7981-firmware mt7981-wo-firmware
ARTIFACTS := preloader.bin bl31-uboot.fip
ARTIFACT/preloader.bin := mt7981-bl2 spim-nand-ddr3
ARTIFACT/bl31-uboot.fip := mt7981-bl31-uboot h3c_magic-nx30-pro
endef
TARGET_DEVICES += h3c_magic-nx30-pro
define Device/jcg_q30-pro
DEVICE_VENDOR := JCG
DEVICE_MODEL := Q30 PRO
DEVICE_DTS := mt7981b-jcg-q30-pro
DEVICE_DTS_DIR := ../dts
UBINIZE_OPTS := -E 5
BLOCKSIZE := 128k
PAGESIZE := 2048
KERNEL_IN_UBI := 1
UBOOTENV_IN_UBI := 1
IMAGES := sysupgrade.itb
KERNEL_INITRAMFS_SUFFIX := -recovery.itb
KERNEL := kernel-bin | gzip
KERNEL_INITRAMFS := kernel-bin | lzma | \
fit lzma $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb with-initrd | pad-to 64k
IMAGE/sysupgrade.itb := append-kernel | \
fit gzip $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb external-static-with-rootfs | append-metadata
DEVICE_PACKAGES := kmod-mt7981-firmware mt7981-wo-firmware
ARTIFACTS := preloader.bin bl31-uboot.fip
ARTIFACT/preloader.bin := mt7981-bl2 spim-nand-ddr3
ARTIFACT/bl31-uboot.fip := mt7981-bl31-uboot jcg_q30-pro
endef
TARGET_DEVICES += jcg_q30-pro
define Device/jdcloud_re-cp-03
DEVICE_VENDOR := JDCloud
DEVICE_MODEL := RE-CP-03
DEVICE_DTS := mt7986a-jdcloud-re-cp-03
DEVICE_DTS_DIR := ../dts
DEVICE_DTC_FLAGS := --pad 4096
DEVICE_DTS_LOADADDR := 0x43f00000
DEVICE_PACKAGES := kmod-mt7986-firmware mt7986-wo-firmware \
e2fsprogs f2fsck mkf2fs
KERNEL_LOADADDR := 0x44000000
KERNEL := kernel-bin | gzip
KERNEL_INITRAMFS := kernel-bin | lzma | \
fit lzma $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb with-initrd | pad-to 64k
KERNEL_INITRAMFS_SUFFIX := -recovery.itb
IMAGES := sysupgrade.itb
IMAGE_SIZE := $$(shell expr 64 + $$(CONFIG_TARGET_ROOTFS_PARTSIZE))m
IMAGE/sysupgrade.itb := append-kernel | \
fit gzip $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb external-static-with-rootfs | \
pad-rootfs | append-metadata
ARTIFACTS :=gpt.bin preloader.bin bl31-uboot.fip
ARTIFACT/gpt.bin := mt798x-gpt emmc
ARTIFACT/preloader.bin := mt7986-bl2 emmc-ddr4
ARTIFACT/bl31-uboot.fip := mt7986-bl31-uboot jdcloud_re-cp-03
endef
TARGET_DEVICES += jdcloud_re-cp-03
define Device/mediatek_mt7981-rfb
DEVICE_VENDOR := MediaTek
DEVICE_MODEL := MT7981 rfb
DEVICE_DTS := mt7981-rfb
DEVICE_DTS_OVERLAY:= \
mt7981-rfb-spim-nand \
mt7981-rfb-mxl-2p5g-phy-eth1 \
mt7981-rfb-mxl-2p5g-phy-swp5
DEVICE_DTS_DIR := $(DTS_DIR)/
DEVICE_DTC_FLAGS := --pad 4096
DEVICE_DTS_LOADADDR := 0x43f00000
DEVICE_PACKAGES := kmod-mt7981-firmware kmod-usb3 e2fsprogs f2fsck mkf2fs mt7981-wo-firmware
KERNEL_LOADADDR := 0x44000000
KERNEL := kernel-bin | gzip
KERNEL_INITRAMFS := kernel-bin | lzma | \
fit lzma $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb with-initrd | pad-to 64k
KERNEL_INITRAMFS_SUFFIX := .itb
KERNEL_IN_UBI := 1
UBOOTENV_IN_UBI := 1
IMAGES := sysupgrade.itb
IMAGE_SIZE := $$(shell expr 64 + $$(CONFIG_TARGET_ROOTFS_PARTSIZE))m
IMAGE/sysupgrade.itb := append-kernel | fit gzip $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb external-with-rootfs | pad-rootfs | append-metadata
ARTIFACTS := \
emmc-preloader.bin emmc-bl31-uboot.fip \
nor-preloader.bin nor-bl31-uboot.fip \
sdcard.img.gz \
snfi-nand-preloader.bin snfi-nand-bl31-uboot.fip \
spim-nand-preloader.bin spim-nand-bl31-uboot.fip
ARTIFACT/emmc-preloader.bin := mt7981-bl2 emmc-ddr3
ARTIFACT/emmc-bl31-uboot.fip := mt7981-bl31-uboot rfb-emmc
ARTIFACT/nor-preloader.bin := mt7981-bl2 nor-ddr3
ARTIFACT/nor-bl31-uboot.fip := mt7981-bl31-uboot rfb-emmc
ARTIFACT/snfi-nand-preloader.bin := mt7981-bl2 snand-ddr3
ARTIFACT/snfi-nand-bl31-uboot.fip := mt7981-bl31-uboot rfb-snfi
ARTIFACT/spim-nand-preloader.bin := mt7981-bl2 spim-nand-ddr3
ARTIFACT/spim-nand-bl31-uboot.fip := mt7981-bl31-uboot rfb-spim-nand
ARTIFACT/sdcard.img.gz := mt798x-gpt sdmmc |\
pad-to 17k | mt7981-bl2 sdmmc-ddr3 |\
pad-to 6656k | mt7981-bl31-uboot rfb-sd |\
$(if $(CONFIG_TARGET_ROOTFS_INITRAMFS),\
pad-to 12M | append-image-stage initramfs.itb | check-size 44m |\
) \
pad-to 44M | mt7981-bl2 spim-nand-ddr3 |\
pad-to 45M | mt7981-bl31-uboot rfb-spim-nand |\
pad-to 49M | mt7981-bl2 nor-ddr3 |\
pad-to 50M | mt7981-bl31-uboot rfb-nor |\
pad-to 51M | mt7981-bl2 snand-ddr3 |\
pad-to 53M | mt7981-bl31-uboot rfb-snfi |\
$(if $(CONFIG_TARGET_ROOTFS_SQUASHFS),\
pad-to 64M | append-image squashfs-sysupgrade.itb | check-size |\
) \
gzip
endef
TARGET_DEVICES += mediatek_mt7981-rfb
define Device/mediatek_mt7986a-rfb-nand
DEVICE_VENDOR := MediaTek
DEVICE_MODEL := MT7986 rfba AP (NAND)
DEVICE_DTS := mt7986a-rfb-spim-nand
DEVICE_DTS_DIR := $(DTS_DIR)/
DEVICE_PACKAGES := kmod-mt7986-firmware mt7986-wo-firmware
SUPPORTED_DEVICES := mediatek,mt7986a-rfb-snand
UBINIZE_OPTS := -E 5
BLOCKSIZE := 128k
PAGESIZE := 2048
IMAGE_SIZE := 65536k
KERNEL_IN_UBI := 1
IMAGES += factory.bin
IMAGE/factory.bin := append-ubi | check-size $$$$(IMAGE_SIZE)
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
KERNEL = kernel-bin | lzma | \
fit lzma $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb
KERNEL_INITRAMFS = kernel-bin | lzma | \
fit lzma $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb with-initrd
endef
TARGET_DEVICES += mediatek_mt7986a-rfb-nand
define Device/mediatek_mt7986b-rfb
DEVICE_VENDOR := MediaTek
DEVICE_MODEL := MTK7986 rfbb AP
DEVICE_DTS := mt7986b-rfb
DEVICE_DTS_DIR := $(DTS_DIR)/
DEVICE_PACKAGES := kmod-mt7986-firmware mt7986-wo-firmware
SUPPORTED_DEVICES := mediatek,mt7986b-rfb
UBINIZE_OPTS := -E 5
BLOCKSIZE := 128k
PAGESIZE := 2048
IMAGE_SIZE := 65536k
KERNEL_IN_UBI := 1
IMAGES += factory.bin
IMAGE/factory.bin := append-ubi | check-size $$$$(IMAGE_SIZE)
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
endef
TARGET_DEVICES += mediatek_mt7986b-rfb
define Device/mediatek_mt7988a-rfb
DEVICE_VENDOR := MediaTek
DEVICE_MODEL := MT7988A rfb
DEVICE_DTS := mt7988a-rfb
DEVICE_DTS_OVERLAY:= \
mt7988a-rfb-emmc \
mt7988a-rfb-sd \
mt7988a-rfb-snfi-nand \
mt7988a-rfb-spim-nand \
mt7988a-rfb-spim-nor \
mt7988a-rfb-eth1-aqr \
mt7988a-rfb-eth1-i2p5g-phy \
mt7988a-rfb-eth1-mxl \
mt7988a-rfb-eth1-sfp \
mt7988a-rfb-eth2-aqr \
mt7988a-rfb-eth2-mxl \
mt7988a-rfb-eth2-sfp
DEVICE_DTS_DIR := $(DTS_DIR)/
DEVICE_DTC_FLAGS := --pad 4096
DEVICE_DTS_LOADADDR := 0x45f00000
DEVICE_PACKAGES := kmod-sfp
KERNEL_LOADADDR := 0x46000000
KERNEL := kernel-bin | gzip
KERNEL_INITRAMFS := kernel-bin | lzma | \
fit lzma $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb with-initrd | pad-to 64k
KERNEL_INITRAMFS_SUFFIX := .itb
KERNEL_IN_UBI := 1
IMAGE_SIZE := $$(shell expr 64 + $$(CONFIG_TARGET_ROOTFS_PARTSIZE))m
IMAGES := sysupgrade.itb
IMAGE/sysupgrade.itb := append-kernel | fit gzip $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb external-with-rootfs | pad-rootfs | append-metadata
ARTIFACTS := \
emmc-gpt.bin emmc-preloader.bin emmc-bl31-uboot.fip \
nor-preloader.bin nor-bl31-uboot.fip \
sdcard.img.gz \
snand-preloader.bin snand-bl31-uboot.fip
ARTIFACT/emmc-gpt.bin := mt798x-gpt emmc
ARTIFACT/emmc-preloader.bin := mt7988-bl2 emmc-comb
ARTIFACT/emmc-bl31-uboot.fip := mt7988-bl31-uboot rfb-emmc
ARTIFACT/nor-preloader.bin := mt7988-bl2 nor-comb
ARTIFACT/nor-bl31-uboot.fip := mt7988-bl31-uboot rfb-nor
ARTIFACT/snand-preloader.bin := mt7988-bl2 spim-nand-comb
ARTIFACT/snand-bl31-uboot.fip := mt7988-bl31-uboot rfb-snand
ARTIFACT/sdcard.img.gz := mt798x-gpt sdmmc |\
pad-to 17k | mt7988-bl2 sdmmc-comb |\
pad-to 6656k | mt7988-bl31-uboot rfb-sd |\
$(if $(CONFIG_TARGET_ROOTFS_INITRAMFS),\
pad-to 12M | append-image-stage initramfs.itb | check-size 44m |\
) \
pad-to 44M | mt7988-bl2 spim-nand-comb |\
pad-to 45M | mt7988-bl31-uboot rfb-snand |\
pad-to 51M | mt7988-bl2 nor-comb |\
pad-to 51M | mt7988-bl31-uboot rfb-nor |\
pad-to 55M | mt7988-bl2 emmc-comb |\
pad-to 56M | mt7988-bl31-uboot rfb-emmc |\
pad-to 62M | mt798x-gpt emmc |\
$(if $(CONFIG_TARGET_ROOTFS_SQUASHFS),\
pad-to 64M | append-image squashfs-sysupgrade.itb | check-size |\
) \
gzip
endef
TARGET_DEVICES += mediatek_mt7988a-rfb
define Device/mercusys_mr90x-v1
DEVICE_VENDOR := MERCUSYS
DEVICE_MODEL := MR90X v1
DEVICE_DTS := mt7986b-mercusys-mr90x-v1
DEVICE_DTS_DIR := ../dts
DEVICE_PACKAGES := kmod-mt7986-firmware mt7986-wo-firmware
UBINIZE_OPTS := -E 5
BLOCKSIZE := 128k
PAGESIZE := 2048
IMAGE_SIZE := 51200k
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
endef
TARGET_DEVICES += mercusys_mr90x-v1
define Device/netcore_n60
DEVICE_VENDOR := Netcore
DEVICE_MODEL := N60
DEVICE_DTS := mt7986a-netcore-n60
DEVICE_DTS_DIR := ../dts
UBINIZE_OPTS := -E 5
BLOCKSIZE := 128k
PAGESIZE := 2048
KERNEL_IN_UBI := 1
UBOOTENV_IN_UBI := 1
IMAGES := sysupgrade.itb
KERNEL_INITRAMFS_SUFFIX := -recovery.itb
KERNEL := kernel-bin | gzip
KERNEL_INITRAMFS := kernel-bin | lzma | \
fit lzma $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb with-initrd | pad-to 64k
IMAGE/sysupgrade.itb := append-kernel | \
fit gzip $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb external-static-with-rootfs | append-metadata
DEVICE_PACKAGES := kmod-mt7986-firmware mt7986-wo-firmware
ARTIFACTS := preloader.bin bl31-uboot.fip
ARTIFACT/preloader.bin := mt7986-bl2 spim-nand-ddr3
ARTIFACT/bl31-uboot.fip := mt7986-bl31-uboot netcore_n60
endef
TARGET_DEVICES += netcore_n60
define Device/netgear_wax220
DEVICE_VENDOR := NETGEAR
DEVICE_MODEL := WAX220
DEVICE_DTS := mt7986b-netgear-wax220
DEVICE_DTS_DIR := ../dts
NETGEAR_ENC_MODEL := WAX220
NETGEAR_ENC_REGION := US
DEVICE_PACKAGES := kmod-mt7986-firmware mt7986-wo-firmware
KERNEL_INITRAMFS_SUFFIX := -recovery.itb
IMAGE_SIZE := 32768k
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
IMAGES += factory.img
# Padding to 10M seems to be required by OEM web interface
IMAGE/factory.img := sysupgrade-tar | \
pad-to 10M | check-size | netgear-encrypted-factory
endef
TARGET_DEVICES += netgear_wax220
define Device/qihoo_360t7
DEVICE_VENDOR := Qihoo
DEVICE_MODEL := 360T7
DEVICE_DTS := mt7981b-qihoo-360t7
DEVICE_DTS_DIR := ../dts
UBINIZE_OPTS := -E 5
BLOCKSIZE := 128k
PAGESIZE := 2048
KERNEL_IN_UBI := 1
UBOOTENV_IN_UBI := 1
IMAGES := sysupgrade.itb
KERNEL_INITRAMFS_SUFFIX := -recovery.itb
KERNEL := kernel-bin | gzip
KERNEL_INITRAMFS := kernel-bin | lzma | \
fit lzma $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb with-initrd | pad-to 64k
IMAGE/sysupgrade.itb := append-kernel | \
fit gzip $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb external-static-with-rootfs | append-metadata
DEVICE_PACKAGES := kmod-mt7981-firmware mt7981-wo-firmware
ARTIFACTS := preloader.bin bl31-uboot.fip
ARTIFACT/preloader.bin := mt7981-bl2 spim-nand-ddr3
ARTIFACT/bl31-uboot.fip := mt7981-bl31-uboot qihoo_360t7
endef
TARGET_DEVICES += qihoo_360t7
define Device/routerich_ax3000
DEVICE_VENDOR := Routerich
DEVICE_MODEL := AX3000
DEVICE_DTS := mt7981b-routerich-ax3000
DEVICE_DTS_DIR := ../dts
DEVICE_PACKAGES := kmod-mt7981-firmware mt7981-wo-firmware kmod-usb3
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
SUPPORTED_DEVICES += mediatek,mt7981-spim-snand-rfb
endef
TARGET_DEVICES += routerich_ax3000
define Device/tplink_tl-xdr-common
DEVICE_VENDOR := TP-Link
DEVICE_DTS_DIR := ../dts
UBINIZE_OPTS := -E 5
BLOCKSIZE := 128k
PAGESIZE := 2048
KERNEL_IN_UBI := 1
UBOOTENV_IN_UBI := 1
IMAGES := sysupgrade.itb
KERNEL_INITRAMFS_SUFFIX := -recovery.itb
KERNEL := kernel-bin | gzip
KERNEL_INITRAMFS := kernel-bin | lzma | \
fit lzma $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb with-initrd | pad-to 64k
IMAGE/sysupgrade.itb := append-kernel | \
fit gzip $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb external-with-rootfs | append-metadata
DEVICE_PACKAGES := kmod-usb3 kmod-mt7986-firmware mt7986-wo-firmware
ARTIFACTS := preloader.bin bl31-uboot.fip
ARTIFACT/preloader.bin := mt7986-bl2 spim-nand-ddr3
endef
define Device/tplink_tl-xdr4288
DEVICE_MODEL := TL-XDR4288
DEVICE_DTS := mt7986a-tplink-tl-xdr4288
ARTIFACT/bl31-uboot.fip := mt7986-bl31-uboot tplink_tl-xdr4288
$(call Device/tplink_tl-xdr-common)
endef
TARGET_DEVICES += tplink_tl-xdr4288
define Device/tplink_tl-xdr6086
DEVICE_MODEL := TL-XDR6086
DEVICE_DTS := mt7986a-tplink-tl-xdr6086
ARTIFACT/bl31-uboot.fip := mt7986-bl31-uboot tplink_tl-xdr6086
$(call Device/tplink_tl-xdr-common)
endef
TARGET_DEVICES += tplink_tl-xdr6086
define Device/tplink_tl-xdr6088
DEVICE_MODEL := TL-XDR6088
DEVICE_DTS := mt7986a-tplink-tl-xdr6088
ARTIFACT/bl31-uboot.fip := mt7986-bl31-uboot tplink_tl-xdr6088
$(call Device/tplink_tl-xdr-common)
endef
TARGET_DEVICES += tplink_tl-xdr6088
define Device/ubnt_unifi-6-plus
DEVICE_VENDOR := Ubiquiti
DEVICE_MODEL := UniFi 6 Plus
DEVICE_DTS := mt7981a-ubnt-unifi-6-plus
DEVICE_DTS_DIR := ../dts
DEVICE_PACKAGES := kmod-mt7981-firmware mt7981-wo-firmware e2fsprogs f2fsck mkf2fs fdisk partx-utils
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
endef
TARGET_DEVICES += ubnt_unifi-6-plus
define Device/unielec_u7981-01
DEVICE_VENDOR := Unielec
DEVICE_MODEL := U7981-01
DEVICE_DTS_DIR := ../dts
DEVICE_PACKAGES := kmod-mt7981-firmware mt7981-wo-firmware kmod-usb3 e2fsprogs f2fsck mkf2fs fdisk partx-utils
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
endef
define Device/unielec_u7981-01-emmc
DEVICE_DTS := mt7981b-unielec-u7981-01-emmc
DEVICE_VARIANT := (EMMC)
$(call Device/unielec_u7981-01)
endef
TARGET_DEVICES += unielec_u7981-01-emmc
define Device/unielec_u7981-01-nand
DEVICE_DTS := mt7981b-unielec-u7981-01-nand
DEVICE_VARIANT := (NAND)
$(call Device/unielec_u7981-01)
endef
TARGET_DEVICES += unielec_u7981-01-nand
define Device/xiaomi_mi-router-ax3000t
DEVICE_VENDOR := Xiaomi
DEVICE_MODEL := Mi Router AX3000T
DEVICE_DTS := mt7981b-xiaomi-mi-router-ax3000t
DEVICE_DTS_DIR := ../dts
UBINIZE_OPTS := -E 5
BLOCKSIZE := 128k
PAGESIZE := 2048
DEVICE_PACKAGES := kmod-mt7981-firmware mt7981-wo-firmware
ifneq ($(CONFIG_TARGET_ROOTFS_INITRAMFS),)
ARTIFACTS := initramfs-factory.ubi
ARTIFACT/initramfs-factory.ubi := append-image-stage initramfs-kernel.bin | ubinize-kernel
endif
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
endef
TARGET_DEVICES += xiaomi_mi-router-ax3000t
define Device/xiaomi_mi-router-ax3000t-ubootmod
DEVICE_VENDOR := Xiaomi
DEVICE_MODEL := Mi Router AX3000T (OpenWrt U-Boot layout)
DEVICE_DTS := mt7981b-xiaomi-mi-router-ax3000t-ubootmod
DEVICE_DTS_DIR := ../dts
UBINIZE_OPTS := -E 5
BLOCKSIZE := 128k
PAGESIZE := 2048
DEVICE_PACKAGES := kmod-mt7981-firmware mt7981-wo-firmware
KERNEL_IN_UBI := 1
UBOOTENV_IN_UBI := 1
IMAGES := sysupgrade.itb
KERNEL_INITRAMFS_SUFFIX := -recovery.itb
KERNEL := kernel-bin | gzip
KERNEL_INITRAMFS := kernel-bin | lzma | \
fit lzma $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb with-initrd | pad-to 64k
IMAGE/sysupgrade.itb := append-kernel | \
fit gzip $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb external-static-with-rootfs | append-metadata
ARTIFACTS := preloader.bin bl31-uboot.fip
ARTIFACT/preloader.bin := mt7981-bl2 spim-nand-ddr3
ARTIFACT/bl31-uboot.fip := mt7981-bl31-uboot xiaomi_mi-router-ax3000t
ifneq ($(CONFIG_TARGET_ROOTFS_INITRAMFS),)
ARTIFACTS += initramfs-factory.ubi
ARTIFACT/initramfs-factory.ubi := append-image-stage initramfs-recovery.itb | ubinize-kernel
endif
endef
TARGET_DEVICES += xiaomi_mi-router-ax3000t-ubootmod
define Device/xiaomi_mi-router-wr30u-stock
DEVICE_VENDOR := Xiaomi
DEVICE_MODEL := Mi Router WR30U (stock layout)
DEVICE_DTS := mt7981b-xiaomi-mi-router-wr30u-stock
DEVICE_DTS_DIR := ../dts
UBINIZE_OPTS := -E 5
BLOCKSIZE := 128k
PAGESIZE := 2048
DEVICE_PACKAGES := kmod-mt7981-firmware mt7981-wo-firmware
ifneq ($(CONFIG_TARGET_ROOTFS_INITRAMFS),)
ARTIFACTS := initramfs-factory.ubi
ARTIFACT/initramfs-factory.ubi := append-image-stage initramfs-kernel.bin | ubinize-kernel
endif
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
endef
TARGET_DEVICES += xiaomi_mi-router-wr30u-stock
define Device/xiaomi_mi-router-wr30u-ubootmod
DEVICE_VENDOR := Xiaomi
DEVICE_MODEL := Mi Router WR30U (OpenWrt U-Boot layout)
DEVICE_DTS := mt7981b-xiaomi-mi-router-wr30u-ubootmod
DEVICE_DTS_DIR := ../dts
UBINIZE_OPTS := -E 5
BLOCKSIZE := 128k
PAGESIZE := 2048
DEVICE_PACKAGES := kmod-mt7981-firmware mt7981-wo-firmware
KERNEL_IN_UBI := 1
UBOOTENV_IN_UBI := 1
IMAGES := sysupgrade.itb
KERNEL_INITRAMFS_SUFFIX := -recovery.itb
KERNEL := kernel-bin | gzip
KERNEL_INITRAMFS := kernel-bin | lzma | \
fit lzma $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb with-initrd | pad-to 64k
IMAGE/sysupgrade.itb := append-kernel | \
fit gzip $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb external-static-with-rootfs | append-metadata
ARTIFACTS := preloader.bin bl31-uboot.fip
ARTIFACT/preloader.bin := mt7981-bl2 spim-nand-ddr3
ARTIFACT/bl31-uboot.fip := mt7981-bl31-uboot xiaomi_mi-router-wr30u
ifneq ($(CONFIG_TARGET_ROOTFS_INITRAMFS),)
ARTIFACTS += initramfs-factory.ubi
ARTIFACT/initramfs-factory.ubi := append-image-stage initramfs-recovery.itb | ubinize-kernel
endif
endef
TARGET_DEVICES += xiaomi_mi-router-wr30u-ubootmod
define Device/xiaomi_redmi-router-ax6000-stock
DEVICE_VENDOR := Xiaomi
DEVICE_MODEL := Redmi Router AX6000 (stock layout)
DEVICE_DTS := mt7986a-xiaomi-redmi-router-ax6000-stock
DEVICE_DTS_DIR := ../dts
DEVICE_PACKAGES := kmod-leds-ws2812b kmod-mt7986-firmware mt7986-wo-firmware
UBINIZE_OPTS := -E 5
BLOCKSIZE := 128k
PAGESIZE := 2048
ifneq ($(CONFIG_TARGET_ROOTFS_INITRAMFS),)
ARTIFACTS := initramfs-factory.ubi
ARTIFACT/initramfs-factory.ubi := append-image-stage initramfs-kernel.bin | ubinize-kernel
endif
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
endef
TARGET_DEVICES += xiaomi_redmi-router-ax6000-stock
define Device/xiaomi_redmi-router-ax6000-ubootmod
DEVICE_VENDOR := Xiaomi
DEVICE_MODEL := Redmi Router AX6000 (OpenWrt U-Boot layout)
DEVICE_DTS := mt7986a-xiaomi-redmi-router-ax6000-ubootmod
DEVICE_DTS_DIR := ../dts
DEVICE_PACKAGES := kmod-leds-ws2812b kmod-mt7986-firmware mt7986-wo-firmware
KERNEL_INITRAMFS_SUFFIX := -recovery.itb
IMAGES := sysupgrade.itb
UBINIZE_OPTS := -E 5
BLOCKSIZE := 128k
PAGESIZE := 2048
KERNEL_IN_UBI := 1
UBOOTENV_IN_UBI := 1
KERNEL := kernel-bin | gzip
KERNEL_INITRAMFS := kernel-bin | lzma | \
fit lzma $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb with-initrd | pad-to 64k
IMAGE/sysupgrade.itb := append-kernel | \
fit gzip $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb external-static-with-rootfs | append-metadata
ARTIFACTS := preloader.bin bl31-uboot.fip
ARTIFACT/preloader.bin := mt7986-bl2 spim-nand-ddr4
ARTIFACT/bl31-uboot.fip := mt7986-bl31-uboot xiaomi_redmi-router-ax6000
ifneq ($(CONFIG_TARGET_ROOTFS_INITRAMFS),)
ARTIFACTS += initramfs-factory.ubi
ARTIFACT/initramfs-factory.ubi := append-image-stage initramfs-recovery.itb | ubinize-kernel
endif
endef
TARGET_DEVICES += xiaomi_redmi-router-ax6000-ubootmod
define Device/yuncore_ax835
DEVICE_VENDOR := YunCore
DEVICE_MODEL := AX835
DEVICE_DTS := mt7981b-yuncore-ax835
DEVICE_DTS_DIR := ../dts
DEVICE_DTS_LOADADDR := 0x47000000
IMAGES := sysupgrade.bin
IMAGE_SIZE := 14336k
SUPPORTED_DEVICES += mediatek,mt7981-spim-nor-rfb
KERNEL := kernel-bin | lzma | \
fit lzma $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb
KERNEL_INITRAMFS := kernel-bin | lzma | \
fit lzma $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb with-initrd | pad-to 64k
IMAGE/sysupgrade.bin := append-kernel | pad-to 128k | append-rootfs | pad-rootfs | check-size | append-metadata
DEVICE_PACKAGES := kmod-mt7981-firmware mt7981-wo-firmware
endef
TARGET_DEVICES += yuncore_ax835
define Device/zbtlink_zbt-z8102ax
DEVICE_VENDOR := Zbtlink
DEVICE_MODEL := ZBT-Z8102AX
DEVICE_DTS := mt7981b-zbtlink-zbt-z8102ax
DEVICE_DTS_DIR := ../dts
DEVICE_PACKAGES := kmod-mt7981-firmware mt7981-wo-firmware kmod-usb3 kmod-usb-net-qmi-wwan kmod-usb-serial-option
KERNEL_IN_UBI := 1
UBINIZE_OPTS := -E 5
BLOCKSIZE := 128k
PAGESIZE := 2048
IMAGE_SIZE := 65536k
IMAGES += factory.bin
IMAGE/factory.bin := append-ubi | check-size $$(IMAGE_SIZE)
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
endef
TARGET_DEVICES += zbtlink_zbt-z8102ax
define Device/zbtlink_zbt-z8103ax
DEVICE_VENDOR := Zbtlink
DEVICE_MODEL := ZBT-Z8103AX
DEVICE_DTS := mt7981b-zbtlink-zbt-z8103ax
DEVICE_DTS_DIR := ../dts
DEVICE_PACKAGES := kmod-mt7981-firmware mt7981-wo-firmware
KERNEL_IN_UBI := 1
UBINIZE_OPTS := -E 5
BLOCKSIZE := 128k
PAGESIZE := 2048
IMAGE_SIZE := 65536k
IMAGES += factory.bin
IMAGE/factory.bin := append-ubi | check-size $$(IMAGE_SIZE)
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
endef
TARGET_DEVICES += zbtlink_zbt-z8103ax
define Device/zyxel_ex5601-t0-stock
DEVICE_VENDOR := Zyxel
DEVICE_MODEL := EX5601-T0
DEVICE_VARIANT := (stock layout)
DEVICE_DTS := mt7986a-zyxel-ex5601-t0-stock
DEVICE_DTS_DIR := ../dts
DEVICE_PACKAGES := kmod-mt7986-firmware mt7986-wo-firmware kmod-usb3
SUPPORTED_DEVICES := mediatek,mt7986a-rfb-snand
UBINIZE_OPTS := -E 5
BLOCKSIZE := 256k
PAGESIZE := 4096
IMAGE_SIZE := 65536k
KERNEL_IN_UBI := 1
IMAGES += factory.bin
IMAGE/factory.bin := append-ubi | check-size $$$$(IMAGE_SIZE)
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
KERNEL = kernel-bin | lzma | \
fit lzma $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb
KERNEL_INITRAMFS = kernel-bin | lzma | \
fit lzma $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb with-initrd
endef
TARGET_DEVICES += zyxel_ex5601-t0-stock
define Device/zyxel_ex5601-t0-ubootmod
DEVICE_VENDOR := Zyxel
DEVICE_MODEL := EX5601-T0
DEVICE_VARIANT := (OpenWrt U-Boot layout)
DEVICE_DTS := mt7986a-zyxel-ex5601-t0-ubootmod
DEVICE_DTS_DIR := ../dts
DEVICE_PACKAGES := kmod-mt7986-firmware mt7986-wo-firmware kmod-usb3
KERNEL_INITRAMFS_SUFFIX := -recovery.itb
IMAGES := sysupgrade.itb
UBINIZE_OPTS := -E 5
BLOCKSIZE := 256k
PAGESIZE := 4096
KERNEL_IN_UBI := 1
UBOOTENV_IN_UBI := 1
KERNEL := kernel-bin | lzma
KERNEL_INITRAMFS := kernel-bin | lzma | \
fit lzma $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb with-initrd
IMAGE/sysupgrade.itb := append-kernel | \
fit lzma $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb external-static-with-rootfs | append-metadata
ARTIFACTS := preloader.bin bl31-uboot.fip
ARTIFACT/preloader.bin := mt7986-bl2 spim-nand-4k-ddr4
ARTIFACT/bl31-uboot.fip := mt7986-bl31-uboot zyxel_ex5601-t0
ifneq ($(CONFIG_TARGET_ROOTFS_INITRAMFS),)
ARTIFACTS += initramfs-factory.ubi
ARTIFACT/initramfs-factory.ubi := append-image-stage initramfs-recovery.itb | ubinize-kernel
endif
endef
TARGET_DEVICES += zyxel_ex5601-t0-ubootmod
define Device/zyxel_ex5700-telenor
DEVICE_VENDOR := ZyXEL
DEVICE_MODEL := EX5700 (Telenor)
DEVICE_DTS := mt7986a-zyxel-ex5700-telenor
DEVICE_DTS_DIR := ../dts
DEVICE_PACKAGES := kmod-mt7916-firmware kmod-ubootenv-nvram kmod-usb3 kmod-mt7986-firmware mt7986-wo-firmware
UBINIZE_OPTS := -E 5
BLOCKSIZE := 128k
PAGESIZE := 2048
IMAGE_SIZE := 65536k
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
endef
TARGET_DEVICES += zyxel_ex5700-telenor
define Device/zyxel_nwa50ax-pro
DEVICE_VENDOR := ZyXEL
DEVICE_MODEL := NWA50AX Pro
DEVICE_DTS := mt7981b-zyxel-nwa50ax-pro
DEVICE_DTS_DIR := ../dts
DEVICE_PACKAGES := kmod-mt7981-firmware mt7981-wo-firmware zyxel-bootconfig
DEVICE_DTS_LOADADDR := 0x44000000
UBINIZE_OPTS := -E 5
BLOCKSIZE := 128k
PAGESIZE := 2048
IMAGE_SIZE := 51200k
KERNEL_IN_UBI := 1
IMAGES += factory.bin
IMAGE/factory.bin := append-ubi | check-size $$$$(IMAGE_SIZE) | zyxel-nwa-fit-filogic
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
endef
TARGET_DEVICES += zyxel_nwa50ax-pro
Reference in New Issue View Git Blame Copy Permalink