mirror of
https://github.com/openwrt/openwrt.git
synced 2024-12-22 23:12:32 +00:00
2ddb2057cd
Xiaomi AX9000 is a premium 802.11ax "tri"-band router/AP. Specifications: * CPU: Qualcomm IPQ8072A Quad core Cortex-A53 2.2GHz * RAM: 1024MB of DDR3 * Storage: 256MB of parallel NAND * Ethernet: * 4x1G RJ45 ports (QCA8075) with 1x status LED per port * 1x2.5G RJ45 port (QCA8081) with 1x status LED * WLAN: * PCI based Qualcomm QCA9889 1x1 802.11ac Wawe 2 for IoT * 2.4GHz: Qualcomm QCN5024 4x4@40MHz 802.11b/g/n/ax 1147 Mbps PHY rate * 5.8GHz: Qualcomm QCN5054 4x4@80MHz or 2x2@160MHz 802.11a/b/g/n/ac/ax 2402Mbps PHY rate * 5GHz: PCI based Qualcomm QCN9024 4x4@160MHz 802.11a/b/g/n/ac/ax 4804Mbps PHY rate * USB: 1x USB3.0 Type-A port * LED-s: * System (Blue and Yellow) * Network (Blue and Yellow) * RGB light bar on top in X shape * Buttons: * 1x Power switch * 1x Soft reset * 1x Mesh button * Power: 12V DC Jack Installation instructions: Obtaining SSH access is mandatory https://openwrt.org/inbox/toh/xiaomi/ax9000#obtain_ssh_access Installation is done by the ubiformat method, through SSH: 1. Open an SSH shell to the router 2. Copy the file openwrt-ipq807x-generic-xiaomi_ax9000-initramfs-factory.ubi to the /tmp directory 3. Check which rootfs partition is your router booted in (0 = rootfs | 1 = rootfs_1): nvram get flag_boot_rootfs 4. Find the rootfs and rootfs_1 mtd indexes respectively: cat /proc/mtd Please confirm if mtd21 and mtd22 are the correct indexes from above! 5. Use the command ubiformat to flash the opposite mtd with UBI image: If nvram get flag_boot_rootfs returned 0: ubiformat /dev/mtd22 -y -f /tmp/openwrt-ipq807x-generic-xiaomi_ax9000-initramfs-factory.ubi && nvram set flag_boot_rootfs=1 && nvram set flag_last_success=1 && nvram commit otherwise: ubiformat /dev/mtd21 -y -f /tmp/openwrt-ipq807x-generic-xiaomi_ax9000-initramfs-factory.ubi && nvram set flag_boot_rootfs=0 && nvram set flag_last_success=0 && nvram commit 6. Reboot the device by: reboot Previous commands flashed an ubinized OpenWrt initramfs that will serve as the intermediate step since OpenWrt uses unified rootfs in order to fully utilize NAND and provide enough space for packages. Continue in order to pernamently flash OpenWrt: 7. SSH into OpenWrt from one of the LAN ports 8. Copy the file openwrt-ipq807x-generic-xiaomi_ax9000-squashfs-sysupgrade.bin to the /tmp directory 9. Sysupgrade the device: sysupgrade -n /tmp/openwrt-ipq807x-generic-xiaomi_ax9000-squashfs-sysupgrade.bin Device will reboot with OpenWrt, and then sysupgrade can be used to upgrade the device when desired. Signed-off-by: Robert Marko <robimarko@gmail.com>
149 lines
5.4 KiB
Makefile
149 lines
5.4 KiB
Makefile
include $(TOPDIR)/rules.mk
|
|
include $(INCLUDE_DIR)/version.mk
|
|
|
|
PKG_NAME:=ipq-wifi
|
|
PKG_RELEASE:=1
|
|
PKG_FLAGS:=nonshared
|
|
|
|
include $(INCLUDE_DIR)/package.mk
|
|
|
|
define Build/Prepare
|
|
mkdir -p $(PKG_BUILD_DIR)
|
|
endef
|
|
|
|
define Build/Compile
|
|
endef
|
|
|
|
# Use ath10k-bdencoder from https://github.com/qca/qca-swiss-army-knife.git
|
|
# to generate the board-* files here.
|
|
#
|
|
# This is intended to be used on an interim basis until device-specific
|
|
# board data for new devices is available through the upstream compilation
|
|
#
|
|
# Please send a mail with your device-specific board files upstream.
|
|
# You can find instructions and examples on the linux-wireless wiki:
|
|
# <https://wireless.wiki.kernel.org/en/users/drivers/ath10k/boardfiles>
|
|
|
|
ALLWIFIBOARDS:= \
|
|
aruba_ap-365 \
|
|
devolo_magic-2-wifi-next \
|
|
edgecore_ecw5410 \
|
|
edgecore_oap100 \
|
|
edimax_cax1800 \
|
|
extreme-networks_ws-ap3915i \
|
|
glinet_gl-a1300 \
|
|
glinet_gl-ap1300 \
|
|
glinet_gl-s1300 \
|
|
linksys_ea8300 \
|
|
linksys_whw03v2 \
|
|
p2w_r619ac \
|
|
pakedge_wr-1 \
|
|
qnap_301w \
|
|
qxwlan_e2600ac-c1 \
|
|
qxwlan_e2600ac-c2 \
|
|
redmi_ax6 \
|
|
sony_ncp-hg100-cellular \
|
|
teltonika_rutx \
|
|
xiaomi_ax3600 \
|
|
xiaomi_ax9000 \
|
|
zte_mf18a \
|
|
zte_mf289f
|
|
|
|
ALLWIFIPACKAGES:=$(foreach BOARD,$(ALLWIFIBOARDS),ipq-wifi-$(BOARD))
|
|
|
|
define Package/ipq-wifi-default
|
|
SUBMENU:=ath10k Board-Specific Overrides
|
|
SECTION:=firmware
|
|
CATEGORY:=Firmware
|
|
DEPENDS:=@(TARGET_ipq40xx||TARGET_ipq806x||TARGET_ipq807x)
|
|
TITLE:=Custom Board
|
|
endef
|
|
|
|
define ipq-wifi-install-one-to
|
|
$(INSTALL_DIR) $(2)/lib/firmware/ath10k/$(3)/
|
|
$(INSTALL_DATA) $(1) $(2)/lib/firmware/ath10k/$(3)/board-2.bin
|
|
endef
|
|
|
|
define ipq-wifi-install-ath11-one-to
|
|
$(INSTALL_DIR) $(2)/lib/firmware/ath11k/$(3)/
|
|
$(INSTALL_DATA) $(1) $(2)/lib/firmware/ath11k/$(3)/board-2.bin
|
|
endef
|
|
|
|
define ipq-wifi-install-one
|
|
$(if $(filter $(suffix $(1)),.QCA4019 .qca4019),\
|
|
$(call ipq-wifi-install-one-to,$(1),$(2),QCA4019/hw1.0),\
|
|
$(if $(filter $(suffix $(1)),.QCA9888 .qca9888),\
|
|
$(call ipq-wifi-install-one-to,$(1),$(2),QCA9888/hw2.0),\
|
|
$(if $(filter $(suffix $(1)),.QCA9889 .qca9889),\
|
|
$(call ipq-wifi-install-one-to,$(1),$(2),QCA9887/hw1.0),\
|
|
$(if $(filter $(suffix $(1)),.QCA9984 .qca9984),\
|
|
$(call ipq-wifi-install-one-to,$(1),$(2),QCA9984/hw1.0),\
|
|
$(if $(filter $(suffix $(1)),.QCA99X0 .qca99x0),\
|
|
$(call ipq-wifi-install-one-to,$(1),$(2),QCA99X0/hw2.0),\
|
|
$(if $(filter $(suffix $(1)),.IPQ8074 .ipq8074),\
|
|
$(call ipq-wifi-install-ath11-one-to,$(1),$(2),IPQ8074/hw2.0),\
|
|
$(if $(filter $(suffix $(1)),.QCN9074 .qcn9074),\
|
|
$(call ipq-wifi-install-ath11-one-to,$(1),$(2),QCN9074/hw1.0),\
|
|
$(error Unrecognized board-file suffix '$(suffix $(1))' for '$(1)')\
|
|
)))))))
|
|
|
|
endef
|
|
# Blank line required at end of above define due to foreach context
|
|
|
|
define generate-ipq-wifi-package
|
|
define Package/ipq-wifi-$(1)
|
|
$(call Package/ipq-wifi-default)
|
|
TITLE:=board-2.bin Overrides for $(2)
|
|
CONFLICTS:=$(PREV_BOARD)
|
|
endef
|
|
|
|
define Package/ipq-wifi-$(1)/description
|
|
The $(2) requires board-specific, reference ("cal") data
|
|
that is not yet present in the upstream wireless firmware distribution.
|
|
|
|
This package supplies board-2.bin file(s) that, in the interim,
|
|
overwrite those supplied by the ath10k-firmware-* packages.
|
|
|
|
This is package is only necessary for the $(2).
|
|
|
|
Do not install it for any other device!
|
|
endef
|
|
|
|
define Package/ipq-wifi-$(1)/install-overlay
|
|
$$$$(foreach IPQ_WIFI_BOARD_FILE,$$$$(wildcard board-$(1).*),\
|
|
$$$$(call ipq-wifi-install-one,$$$$(IPQ_WIFI_BOARD_FILE),$$(1)))
|
|
endef
|
|
|
|
PREV_BOARD+=ipq-wifi-$(1)
|
|
endef
|
|
|
|
# Add board name to ALLWIFIBOARDS
|
|
# Place files in this directory as board-<devicename>.<qca4019|qca9888|qca9889|qca9984|qca99x0|ipq8074>
|
|
# Add $(eval $(call generate-ipq-wifi-package,<devicename>,<display name>))
|
|
|
|
$(eval $(call generate-ipq-wifi-package,aruba_ap-365,Aruba AP-365))
|
|
$(eval $(call generate-ipq-wifi-package,devolo_magic-2-wifi-next,devolo Magic 2 WiFi next))
|
|
$(eval $(call generate-ipq-wifi-package,edgecore_ecw5410,Edgecore ECW5410))
|
|
$(eval $(call generate-ipq-wifi-package,edgecore_oap100,Edgecore OAP100))
|
|
$(eval $(call generate-ipq-wifi-package,edimax_cax1800,Edimax CAX1800))
|
|
$(eval $(call generate-ipq-wifi-package,extreme-networks_ws-ap3915i,Edgecore OAP100))
|
|
$(eval $(call generate-ipq-wifi-package,glinet_gl-a1300,GL.iNet GL-A1300))
|
|
$(eval $(call generate-ipq-wifi-package,glinet_gl-ap1300,GL.iNet GL-AP1300))
|
|
$(eval $(call generate-ipq-wifi-package,glinet_gl-s1300,GL.iNet GL-S1300))
|
|
$(eval $(call generate-ipq-wifi-package,linksys_ea8300,Linksys EA8300))
|
|
$(eval $(call generate-ipq-wifi-package,linksys_whw03v2,Linksys WHW03 V2))
|
|
$(eval $(call generate-ipq-wifi-package,p2w_r619ac,P&W R619AC))
|
|
$(eval $(call generate-ipq-wifi-package,pakedge_wr-1,Pakedge WR-1))
|
|
$(eval $(call generate-ipq-wifi-package,qnap_301w,QNAP 301w))
|
|
$(eval $(call generate-ipq-wifi-package,qxwlan_e2600ac-c1,Qxwlan E2600AC C1))
|
|
$(eval $(call generate-ipq-wifi-package,qxwlan_e2600ac-c2,Qxwlan E2600AC C2))
|
|
$(eval $(call generate-ipq-wifi-package,redmi_ax6,Redmi AX6))
|
|
$(eval $(call generate-ipq-wifi-package,sony_ncp-hg100-cellular,Sony NCP-HG100/Cellular))
|
|
$(eval $(call generate-ipq-wifi-package,teltonika_rutx,Teltonika RUTX))
|
|
$(eval $(call generate-ipq-wifi-package,xiaomi_ax3600,Xiaomi AX3600))
|
|
$(eval $(call generate-ipq-wifi-package,xiaomi_ax9000,Xiaomi AX9000))
|
|
$(eval $(call generate-ipq-wifi-package,zte_mf18a,ZTE MF18A))
|
|
$(eval $(call generate-ipq-wifi-package,zte_mf289f,ZTE MF289F))
|
|
|
|
$(foreach PACKAGE,$(ALLWIFIPACKAGES),$(eval $(call BuildPackage,$(PACKAGE))))
|