mirror of
https://github.com/openwrt/openwrt.git
synced 2024-12-29 10:08:59 +00:00
cb741654e5
Use the generic board detection for the GnuBee Personal Cloud Two
instead of the target specific one as all recent additions are doing.
Fixup the pinmux to set all pins used as GPIO to the function GPIO.
Request pins where used.
Drop the i2c from the dts. There is nothing connected. While at it fix an
indentation issue and use references instead of duplicating the whole
node path.
Use the same switch config as for the GB-PC1 and drop the led trigger for
the not supported IP1001 phy connected to second rgmii.
Fixes: c60a21532b ("ramips: Add support for the GnuBee Personal Cloud Two")
Signed-off-by: Mathias Kresin <dev@kresin.me>
135 lines
2.0 KiB
Plaintext
135 lines
2.0 KiB
Plaintext
/dts-v1/;
|
|
|
|
#include "mt7621.dtsi"
|
|
|
|
#include <dt-bindings/gpio/gpio.h>
|
|
#include <dt-bindings/input/input.h>
|
|
|
|
/ {
|
|
compatible = "gnubee,gb-pc2", "mediatek,mt7621-soc";
|
|
model = "GB-PC2";
|
|
|
|
memory@0 {
|
|
device_type = "memory";
|
|
reg = <0x0 0x1c000000>, <0x20000000 0x4000000>;
|
|
};
|
|
|
|
chosen {
|
|
bootargs = "console=ttyS0,57600";
|
|
};
|
|
|
|
gpio-keys-polled {
|
|
compatible = "gpio-keys-polled";
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
poll-interval = <20>;
|
|
|
|
reset {
|
|
label = "reset";
|
|
gpios = <&gpio0 18 GPIO_ACTIVE_HIGH>;
|
|
linux,code = <KEY_RESTART>;
|
|
};
|
|
};
|
|
|
|
gpio-leds {
|
|
compatible = "gpio-leds";
|
|
|
|
system {
|
|
label = "gb-pc2:green:system";
|
|
gpios = <&gpio0 6 GPIO_ACTIVE_LOW>;
|
|
};
|
|
|
|
status {
|
|
label = "gb-pc2:green:status";
|
|
gpios = <&gpio0 8 GPIO_ACTIVE_LOW>;
|
|
};
|
|
|
|
lan1 {
|
|
label = "gb-pc2:green:lan1";
|
|
gpios = <&gpio0 24 GPIO_ACTIVE_LOW>;
|
|
};
|
|
|
|
lan2 {
|
|
label = "gb-pc2:green:lan2";
|
|
gpios = <&gpio0 25 GPIO_ACTIVE_LOW>;
|
|
};
|
|
|
|
lan3-yellow {
|
|
label = "gb-pc2:yellow:lan3";
|
|
gpios = <&gpio0 13 GPIO_ACTIVE_LOW>;
|
|
};
|
|
|
|
lan3-green {
|
|
label = "gb-pc2:green:lan3";
|
|
gpios = <&gpio0 15 GPIO_ACTIVE_LOW>;
|
|
};
|
|
|
|
};
|
|
};
|
|
|
|
&sdhci {
|
|
status = "okay";
|
|
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&sdhci_pins>;
|
|
};
|
|
|
|
&spi0 {
|
|
status = "okay";
|
|
|
|
m25p80@0 {
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
compatible = "jedec,spi-nor";
|
|
reg = <0>;
|
|
spi-max-frequency = <10000000>;
|
|
m25p,chunked-io = <32>;
|
|
|
|
partition@0 {
|
|
label = "u-boot";
|
|
reg = <0x0 0x30000>;
|
|
read-only;
|
|
};
|
|
|
|
partition@30000 {
|
|
label = "u-boot-env";
|
|
reg = <0x30000 0x10000>;
|
|
read-only;
|
|
};
|
|
|
|
factory: partition@40000 {
|
|
label = "factory";
|
|
reg = <0x40000 0x10000>;
|
|
read-only;
|
|
};
|
|
|
|
partition@50000 {
|
|
label = "firmware";
|
|
reg = <0x50000 0x1fb0000>;
|
|
};
|
|
};
|
|
};
|
|
|
|
&cpuclock {
|
|
compatible = "fixed-clock";
|
|
clock-frequency = <900000000>;
|
|
};
|
|
|
|
&pcie {
|
|
status = "okay";
|
|
};
|
|
|
|
ðernet {
|
|
mtd-mac-address = <&factory 0xe000>;
|
|
};
|
|
|
|
&pinctrl {
|
|
state_default: pinctrl0 {
|
|
gpio {
|
|
ralink,group = "jtag", "rgmii3", "uart3", "wdt";
|
|
ralink,function = "gpio";
|
|
};
|
|
};
|
|
};
|
|
|