mirror of
https://github.com/openwrt/openwrt.git
synced 2024-12-22 23:12:32 +00:00
2b4ac79a79
SOC: IPQ4018 / QCA Dakota CPU: Quad-Core ARMv7 Processor rev 5 (v7l) Cortex-A7 DRAM: 256 MiB NOR: 32 MiB ETH: Qualcomm Atheros QCA8072 WLAN1: Qualcomm Atheros QCA4018 2.4GHz 802.11bgn 2:2x2 WLAN2: Qualcomm Atheros QCA4018 5GHz 802.11a/n/ac 2:2x2 INPUT: RESET Button LEDS: Power, LAN, MESH, WLAN 2.4GHz, WLAN 5GHz 1. Load Ramdisk via U-Boot To set up the flash memory environment, do the following: a. As a preliminary step, ensure that the board console port is connected to the PC using these RS232 parameters: * 115200bps * 8N1 b. Confirm that the PC is connected to the board using one of the Ethernet ports. Set a static ip 192.168.99.8 for Ethernet that connects to board. The PC must have a TFTP server launched and listening on the interface to which the board is connected. At this stage power up the board and, after a few seconds, press 4 and then any key during the countdown. U-BOOT> set serverip 192.168.99.8 && set ipaddr 192.168.99.9 && tftpboot 0x84000000 openwrt.itb && bootm 2. Load image via GUI a. Upgrade EAP1300 to FW v3.5.3.2 In the GUI, System Manager > Firmware > Firmware Upgrade, to do upgrade. b. Transfer to OpenWrt from EnGenius. In Firmware Upgrade page, to upgrade yours openwrt-ipq40xx-engenius_eap1300-squashfs-sysupgrade.bin. 3. Revert to EnGenius EAP1300 To flash openwrt-ipq40xx-engenius_eap1300-squashfs-factory.bin by using sysupgrade command and "DO NOT" keep configuration. $ sysupgrade –n openwrt-ipq40xx-engenius_eap1300-squashfs-factory.bin Signed-off-by: Steven Lin <steven.lin@senao.com> |
||
|---|---|---|
| .. | ||
| 030-mtd-nand-Use-standard-large-page-OOB-layout-when-usi.patch | ||
| 031-mtd-nand-use-usual-return-values-for-the-erase-hook.patch | ||
| 040-dmaengine-qcom-bam-Process-multiple-pending-descript.patch | ||
| 050-0002-mtd-nand-qcom-add-command-elements-in-BAM-transactio.patch | ||
| 050-0003-mtd-nand-qcom-support-for-command-descriptor-formati.patch | ||
| 050-0004-mtd-nand-provide-several-helpers-to-do-common-NAND-o.patch | ||
| 050-0005-mtd-nand-force-drivers-to-explicitly-send-READ-PROG-.patch | ||
| 070-qcom-spm-fix-probe-order.patch | ||
| 071-qcom-ipq4019-use-v2-of-the-kpss-bringup-mechanism.patch | ||
| 072-qcom-ipq4019-add-cpu-operating-points-for-cpufreq-su.patch | ||
| 073-qcom-ipq4019-fix-cpu0-s-qcom-saw2-reg-value.patch | ||
| 074-ARM-qcom-Add-IPQ4019-SoC-support.patch | ||
| 075-dt-bindings-phy-qcom-ipq4019-usb-add-binding-documen.patch | ||
| 076-phy-qcom-ipq4019-usb-add-driver-for-QCOM-IPQ4019.patch | ||
| 077-qcom-ipq4019-add-USB-devicetree-nodes.patch | ||
| 078-ARM-dts-ipq4019-Add-a-few-peripheral-nodes.patch | ||
| 079-ARM-dts-ipq4019-fix-PCI-range.patch | ||
| 080-pinctrl-msm-fix-gpio-hog-related-boot-issues.patch | ||
| 081-clk-fix-apss-cpu-overclocking.patch | ||
| 082-ARM-dts-ipq4019-Add-TZ-and-SMEM-reserved-regions.patch | ||
| 083-mtd-nand-add-Winbond-manufacturer-and-chip.patch | ||
| 303-spi-nor-enable-4B-opcodes-for-mx25l25635f.patch | ||
| 700-net-add-qualcomm-mdio-and-phy.patch | ||
| 701-dts-ipq4019-add-mdio-node.patch | ||
| 702-dts-ipq4019-add-PHY-switch-nodes.patch | ||
| 703-net-IPQ4019-needs-rfs-vlan_tag-callbacks-in.patch | ||
| 710-net-add-qualcomm-essedma-ethernet-driver.patch | ||
| 711-dts-ipq4019-add-ethernet-essedma-node.patch | ||
| 712-mr33-essedma.patch | ||
| 713-essedma-alloc-skb-ip-align.patch | ||
| 850-soc-add-qualcomm-syscon.patch | ||
| 900-dts-ipq4019-ap-dk01.1.patch | ||
| 901-arm-boot-add-dts-files.patch | ||
| 997-device_tree_cmdline.patch | ||