openwrt/target/linux/mediatek/dts/mt7986a-xiaomi-redmi-router-ax6000.dtsi
Chen Minqiang 36746893ac mediatek: fix the name of buswidth to bus-width
Fix the issue of dts buswidth cannot be applied properly with spi driver.
Fix the name of buswidth to bus-width in dts in order to fit the format
in linux spi kernel[1] so that spi-tx-bus-width & spi-rx-bus-width can be
parsed properly.

[1] Documentation/devicetree/bindings/spi/spi-controller.yaml

Signed-off-by: Chen Minqiang <ptpt52@gmail.com>
2023-09-05 15:40:43 +08:00

276 lines
4.5 KiB
Plaintext

// SPDX-License-Identifier: (GPL-2.0 OR MIT)
/dts-v1/;
#include <dt-bindings/input/input.h>
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/leds/common.h>
#include "mt7986a.dtsi"
/ {
aliases {
serial0 = &uart0;
led-boot = &led_status_rgb;
led-failsafe = &led_status_rgb;
led-running = &led_status_rgb;
led-upgrade = &led_status_rgb;
};
chosen {
stdout-path = "serial0:115200n8";
};
memory {
reg = <0 0x40000000 0 0x20000000>;
};
keys {
compatible = "gpio-keys";
reset {
label = "reset";
gpios = <&pio 9 GPIO_ACTIVE_LOW>;
linux,code = <KEY_RESTART>;
};
mesh {
label = "mesh";
gpios = <&pio 10 GPIO_ACTIVE_LOW>;
linux,code = <BTN_9>;
linux,input-type = <EV_SW>;
};
};
};
&crypto {
status = "okay";
};
&eth {
status = "okay";
gmac0: mac@0 {
compatible = "mediatek,eth-mac";
reg = <0>;
phy-mode = "2500base-x";
nvmem-cells = <&macaddr_factory_4>;
nvmem-cell-names = "mac-address";
mac-address-increment = <(-1)>;
fixed-link {
speed = <2500>;
full-duplex;
pause;
};
};
mdio: mdio-bus {
#address-cells = <1>;
#size-cells = <0>;
};
};
&mdio {
switch: switch@0 {
compatible = "mediatek,mt7531";
reg = <31>;
reset-gpios = <&pio 5 GPIO_ACTIVE_HIGH>;
interrupt-controller;
#interrupt-cells = <1>;
interrupt-parent = <&pio>;
interrupts = <66 IRQ_TYPE_LEVEL_HIGH>;
};
};
&pio {
spi_flash_pins: spi-flash-pins-33-to-38 {
mux {
function = "spi";
groups = "spi0", "spi0_wp_hold";
};
conf-pu {
pins = "SPI2_CS", "SPI2_HOLD", "SPI2_WP";
drive-strength = <8>;
mediatek,pull-up-adv = <0>; /* bias-disable */
};
conf-pd {
pins = "SPI2_CLK", "SPI2_MOSI", "SPI2_MISO";
drive-strength = <8>;
mediatek,pull-down-adv = <0>; /* bias-disable */
};
};
spi_led_pins: spic-pins-29-to-32 {
mux {
function = "spi";
groups = "spi1_2";
};
};
wf_2g_5g_pins: wf_2g_5g-pins {
mux {
function = "wifi";
groups = "wf_2g", "wf_5g";
};
conf {
pins = "WF0_HB1", "WF0_HB2", "WF0_HB3", "WF0_HB4",
"WF0_HB0", "WF0_HB0_B", "WF0_HB5", "WF0_HB6",
"WF0_HB7", "WF0_HB8", "WF0_HB9", "WF0_HB10",
"WF0_TOP_CLK", "WF0_TOP_DATA", "WF1_HB1",
"WF1_HB2", "WF1_HB3", "WF1_HB4", "WF1_HB0",
"WF1_HB5", "WF1_HB6", "WF1_HB7", "WF1_HB8",
"WF1_TOP_CLK", "WF1_TOP_DATA";
drive-strength = <4>;
};
};
};
&spi0 {
pinctrl-names = "default";
pinctrl-0 = <&spi_flash_pins>;
status = "okay";
spi_nand_flash: flash@0 {
compatible = "spi-nand";
#address-cells = <1>;
#size-cells = <1>;
reg = <0>;
spi-max-frequency = <20000000>;
spi-tx-bus-width = <4>;
spi-rx-bus-width = <4>;
partitions: partitions {
compatible = "fixed-partitions";
#address-cells = <1>;
#size-cells = <1>;
partition@0 {
label = "BL2";
reg = <0x0 0x100000>;
read-only;
};
partition@100000 {
label = "Nvram";
reg = <0x100000 0x40000>;
};
partition@140000 {
label = "Bdata";
reg = <0x140000 0x40000>;
};
factory: partition@180000 {
label = "Factory";
reg = <0x180000 0x200000>;
read-only;
compatible = "nvmem-cells";
#address-cells = <1>;
#size-cells = <1>;
macaddr_factory_4: macaddr@4 {
reg = <0x4 0x6>;
};
};
partition@380000 {
label = "FIP";
reg = <0x380000 0x200000>;
read-only;
};
};
};
};
&spi1 {
pinctrl-names = "default";
pinctrl-0 = <&spi_led_pins>;
status = "okay";
ws2812b@0 {
#address-cells = <1>;
#size-cells = <0>;
compatible = "worldsemi,ws2812b";
reg = <0>;
spi-max-frequency = <3000000>;
led_status_rgb: led@0 {
reg = <0>;
label = "rgb:status";
color-index = <LED_COLOR_ID_RED LED_COLOR_ID_GREEN LED_COLOR_ID_BLUE>;
};
led_network_rgb: led@1 {
reg = <1>;
label = "rgb:network";
color-index = <LED_COLOR_ID_RED LED_COLOR_ID_GREEN LED_COLOR_ID_BLUE>;
};
};
};
&switch {
ports {
#address-cells = <1>;
#size-cells = <0>;
port@1 {
reg = <1>;
label = "lan4";
};
port@2 {
reg = <2>;
label = "lan3";
};
port@3 {
reg = <3>;
label = "lan2";
};
port@4 {
reg = <4>;
label = "wan";
};
port@6 {
reg = <6>;
ethernet = <&gmac0>;
phy-mode = "2500base-x";
fixed-link {
speed = <2500>;
full-duplex;
pause;
};
};
};
};
&trng {
status = "okay";
};
&uart0 {
status = "okay";
};
&watchdog {
status = "okay";
};
&wifi {
status = "okay";
pinctrl-names = "default";
pinctrl-0 = <&wf_2g_5g_pins>;
mediatek,mtd-eeprom = <&factory 0x0>;
};
&uart0 {
status = "okay";
};