mirror of
https://github.com/openwrt/openwrt.git
synced 2024-12-29 10:08:59 +00:00
a9071d02b5
The Linksys MR8300 is based on QCA4019 and QCA9888 and provides three, independent radios. NAND provides two, alternate kernel/firmware images with fail-over provided by the OEM U-Boot. Hardware Highlights: SoC: IPQ4019 at 717 MHz (4 CPUs) RAM: 512MB RAM SoC: Qualcomm IPQ4019 at 717 MHz (4 CPUs) RAM: 512M DDR3 FLASH: 256 MB NAND (Winbond W29N02GV, 8-bit parallel) ETH: Qualcomm QCA8075 (4x GigE LAN, 1x GigE Internet Ethernet Jacks) BTN: Reset and WPS USB: USB3.0, single port on rear with LED SERIAL: Serial pads internal (unpopulated) LED: Four status lights on top + USB LED WIFI1: 2x2:2 QCA4019 2.4 GHz radio on ch. 1-14 WIFI2: 2x2:2 QCA4019 5 GHz radio on ch. 36-64 WIFI3: 2x2:2 QCA9888 5 GHz radio on ch. 100-165 Support is based on the already supported EA8300. Key differences: EA8300 has 256MB RAM where MR8300 has 512MB RAM. MR8300 has a revised top panel LED setup. Installation: "Factory" images may be installed directly through the OEM GUI using URL: https://ip-of-router/fwupdate.html (Typically 192.168.1.1) Signed-off-by: Hans Geiblinger <cybrnook2002@yahoo.com> [copied Hardware-highlights from EA8300. Fixed alphabetical order. fixed commit subject, removed bogus unit-address of keys, fixed author (used Signed-off-By to From:) ] Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
123 lines
2.9 KiB
Bash
Executable File
123 lines
2.9 KiB
Bash
Executable File
linksys_get_target_firmware() {
|
|
local cur_boot_part mtd_ubi0
|
|
|
|
cur_boot_part="$(/usr/sbin/fw_printenv -n boot_part)"
|
|
if [ -z "${cur_boot_part}" ]; then
|
|
mtd_ubi0=$(cat /sys/devices/virtual/ubi/ubi0/mtd_num)
|
|
case "$(grep -E "^mtd${mtd_ubi0}:" /proc/mtd | cut -d '"' -f 2)" in
|
|
kernel|rootfs)
|
|
cur_boot_part=1
|
|
;;
|
|
alt_kernel|alt_rootfs)
|
|
cur_boot_part=2
|
|
;;
|
|
esac
|
|
>&2 printf "Current boot_part='%s' selected from ubi0/mtd_num='%s'" \
|
|
"${cur_boot_part}" "${mtd_ubi0}"
|
|
fi
|
|
|
|
# OEM U-Boot for EA6350v3, EA8300 and MR8300; bootcmd=
|
|
# if test $auto_recovery = no;
|
|
# then bootipq;
|
|
# elif test $boot_part = 1;
|
|
# then run bootpart1;
|
|
# else run bootpart2;
|
|
# fi
|
|
|
|
case "$cur_boot_part" in
|
|
1)
|
|
fw_setenv -s - <<-EOF
|
|
boot_part 2
|
|
auto_recovery yes
|
|
EOF
|
|
printf "alt_kernel"
|
|
return
|
|
;;
|
|
2)
|
|
fw_setenv -s - <<-EOF
|
|
boot_part 1
|
|
auto_recovery yes
|
|
EOF
|
|
printf "kernel"
|
|
return
|
|
;;
|
|
*)
|
|
return
|
|
;;
|
|
esac
|
|
}
|
|
|
|
linksys_get_root_magic() {
|
|
(get_image "$@" | dd skip=786432 bs=4 count=1 | hexdump -v -n 4 -e '1/1 "%02x"') 2>/dev/null
|
|
}
|
|
|
|
platform_do_upgrade_linksys() {
|
|
local magic_long="$(get_magic_long "$1")"
|
|
|
|
local rm_oem_fw_vols="squashfs ubifs" # from OEM [alt_]rootfs UBI
|
|
local vol
|
|
|
|
mkdir -p /var/lock
|
|
local part_label="$(linksys_get_target_firmware)"
|
|
touch /var/lock/fw_printenv.lock
|
|
|
|
if [ -z "$part_label" ]; then
|
|
echo "cannot find target partition"
|
|
exit 1
|
|
fi
|
|
|
|
local target_mtd=$(find_mtd_part "$part_label")
|
|
|
|
[ "$magic_long" = "73797375" ] && {
|
|
CI_KERNPART="$part_label"
|
|
if [ "$part_label" = "kernel" ]; then
|
|
CI_UBIPART="rootfs"
|
|
else
|
|
CI_UBIPART="alt_rootfs"
|
|
fi
|
|
|
|
local mtdnum="$(find_mtd_index "$CI_UBIPART")"
|
|
if [ ! "$mtdnum" ]; then
|
|
echo "cannot find ubi mtd partition $CI_UBIPART"
|
|
return 1
|
|
fi
|
|
|
|
local ubidev="$(nand_find_ubi "$CI_UBIPART")"
|
|
if [ ! "$ubidev" ]; then
|
|
ubiattach -m "$mtdnum"
|
|
sync
|
|
ubidev="$(nand_find_ubi "$CI_UBIPART")"
|
|
fi
|
|
|
|
if [ "$ubidev" ]; then
|
|
for vol in $rm_oem_fw_vols; do
|
|
ubirmvol "/dev/$ubidev" -N "$vol" 2>/dev/null
|
|
done
|
|
fi
|
|
|
|
# complete std upgrade
|
|
nand_upgrade_tar "$1"
|
|
}
|
|
|
|
[ "$magic_long" = "27051956" ] && {
|
|
# This magic is for a uImage (which is a sysupgrade image)
|
|
# check firmwares' rootfs types
|
|
local oldroot="$(linksys_get_root_magic "$target_mtd")"
|
|
local newroot="$(linksys_get_root_magic "$1")"
|
|
|
|
if [ "$newroot" = "55424923" ] && [ "$oldroot" = "55424923" ]; then
|
|
# we're upgrading from a firmware with UBI to one with UBI
|
|
# erase everything to be safe
|
|
# - Is that really needed? Won't remove (or comment) the if,
|
|
# because it may be needed in a future device.
|
|
#mtd erase $part_label
|
|
#get_image "$1" | mtd -n write - $part_label
|
|
echo "writing \"$1\" UBI image to \"$part_label\" (UBI)..."
|
|
get_image "$1" | mtd write - "$part_label"
|
|
else
|
|
echo "writing \"$1\" image to \"$part_label\""
|
|
get_image "$1" | mtd write - "$part_label"
|
|
fi
|
|
}
|
|
}
|