mirror of
https://github.com/openwrt/openwrt.git
synced 2025-01-04 04:54:18 +00:00
35acdbe909
The dual-boot partition layout for the Zyxel GS1900 switches results in 6.9MB for both kernel and rootfs. Depending on the package selection, this may already leave no space for the user overlay. Merge the two firmware partitions, effectively dropping dual boot support with OpenWrt. This results in a firmware partition of 13.9MB, which should leave some room for the future. To maintain install capabilites on new devices, an image is required that still fits inside the original partition. The initramfs is used as factory install image, so ensure this meets the old size constraints. The factory image can be flashed via the same procedure as vendor images when reverting to stock, can be installed from stock, or can be launched via tftpboot. Link: https://github.com/openwrt/openwrt/issues/16439 Link: https://github.com/openwrt/openwrt/pull/16442 Tested-by: Stijn Segers <foss@volatilesystems.org> Signed-off-by: Sander Vanheule <sander@svanheule.net>
146 lines
2.5 KiB
Plaintext
146 lines
2.5 KiB
Plaintext
// SPDX-License-Identifier: GPL-2.0-or-later
|
|
|
|
#include "rtl838x.dtsi"
|
|
|
|
#include <dt-bindings/input/input.h>
|
|
#include <dt-bindings/gpio/gpio.h>
|
|
|
|
/ {
|
|
aliases {
|
|
led-boot = &led_sys;
|
|
led-failsafe = &led_sys;
|
|
led-running = &led_sys;
|
|
led-upgrade = &led_sys;
|
|
};
|
|
|
|
memory@0 {
|
|
device_type = "memory";
|
|
reg = <0x0 0x8000000>;
|
|
};
|
|
|
|
keys {
|
|
compatible = "gpio-keys-polled";
|
|
poll-interval = <20>;
|
|
|
|
reset {
|
|
label = "reset";
|
|
gpios = <&gpio1 3 GPIO_ACTIVE_LOW>;
|
|
linux,code = <KEY_RESTART>;
|
|
};
|
|
};
|
|
|
|
leds {
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&pinmux_disable_sys_led>;
|
|
compatible = "gpio-leds";
|
|
|
|
led_sys: sys {
|
|
label = "green:sys";
|
|
gpios = <&gpio0 0 GPIO_ACTIVE_HIGH>;
|
|
};
|
|
};
|
|
|
|
gpio1: rtl8231-gpio {
|
|
compatible = "realtek,rtl8231-gpio";
|
|
#gpio-cells = <2>;
|
|
gpio-controller;
|
|
indirect-access-bus-id = <0>;
|
|
|
|
poe_enable {
|
|
gpio-hog;
|
|
gpios = <13 GPIO_ACTIVE_HIGH>;
|
|
output-high;
|
|
};
|
|
};
|
|
};
|
|
|
|
&spi0 {
|
|
status = "okay";
|
|
|
|
flash@0 {
|
|
compatible = "jedec,spi-nor";
|
|
reg = <0>;
|
|
spi-max-frequency = <10000000>;
|
|
|
|
partitions {
|
|
compatible = "fixed-partitions";
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
|
|
partition@0 {
|
|
label = "u-boot";
|
|
reg = <0x0 0x40000>;
|
|
read-only;
|
|
};
|
|
partition@40000 {
|
|
label = "u-boot-env";
|
|
reg = <0x40000 0x10000>;
|
|
read-only;
|
|
};
|
|
partition@50000 {
|
|
label = "u-boot-env2";
|
|
reg = <0x50000 0x10000>;
|
|
};
|
|
partition@60000 {
|
|
label = "jffs";
|
|
reg = <0x60000 0x100000>;
|
|
};
|
|
partition@160000 {
|
|
label = "jffs2";
|
|
reg = <0x160000 0x100000>;
|
|
};
|
|
partition@b260000 {
|
|
label = "firmware";
|
|
reg = <0x260000 0xda0000>;
|
|
compatible = "openwrt,uimage", "denx,uimage";
|
|
openwrt,ih-magic = <0x83800000>;
|
|
};
|
|
};
|
|
};
|
|
};
|
|
|
|
ðernet0 {
|
|
mdio: mdio-bus {
|
|
compatible = "realtek,rtl838x-mdio";
|
|
regmap = <ðernet0>;
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
|
|
INTERNAL_PHY(8)
|
|
INTERNAL_PHY(9)
|
|
INTERNAL_PHY(10)
|
|
INTERNAL_PHY(11)
|
|
INTERNAL_PHY(12)
|
|
INTERNAL_PHY(13)
|
|
INTERNAL_PHY(14)
|
|
INTERNAL_PHY(15)
|
|
};
|
|
};
|
|
|
|
&switch0 {
|
|
ports {
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
|
|
SWITCH_PORT(8, 1, internal)
|
|
SWITCH_PORT(9, 2, internal)
|
|
SWITCH_PORT(10, 3, internal)
|
|
SWITCH_PORT(11, 4, internal)
|
|
SWITCH_PORT(12, 5, internal)
|
|
SWITCH_PORT(13, 6, internal)
|
|
SWITCH_PORT(14, 7, internal)
|
|
SWITCH_PORT(15, 8, internal)
|
|
|
|
port@28 {
|
|
ethernet = <ðernet0>;
|
|
reg = <28>;
|
|
phy-mode = "internal";
|
|
|
|
fixed-link {
|
|
speed = <1000>;
|
|
full-duplex;
|
|
};
|
|
};
|
|
};
|
|
};
|