mirror of
https://github.com/openwrt/openwrt.git
synced 2024-12-23 15:32:33 +00:00
9703a2adcc
Refresh all patches on top of kernel 5.10.138. The following patches were applied upstream: bcm27xx/patches-5.10/950-0311-drm-vc4-Adopt-the-dma-configuration-from-the-HVS-or-.patch bcm27xx/patches-5.10/950-0317-vc4_hdmi-Remove-firmware-logic-for-MAI-threshold-set.patch bcm27xx/patches-5.10/950-0346-drm-vc4-A-present-but-empty-dmas-disables-audio.patch bcm27xx/patches-5.10/950-0354-drm-vc4-Add-the-2711-HVS-as-a-suitable-DMA-node.patch bcm27xx/patches-5.10/950-0413-drm-vc4-hdmi-Don-t-access-the-connector-state-in-res.patch bcm27xx/patches-5.10/950-0505-vc4-drm-Avoid-full-hdmi-audio-fifo-writes.patch bcm27xx/patches-5.10/950-0512-vc4-drm-vc4_plane-Remove-subpixel-positioning-check.patch bcm27xx/patches-5.10/950-0560-drm-vc4-drv-Remove-the-DSI-pointer-in-vc4_drv.patch bcm27xx/patches-5.10/950-0561-drm-vc4-dsi-Use-snprintf-for-the-PHY-clocks-instead-.patch bcm27xx/patches-5.10/950-0562-drm-vc4-dsi-Introduce-a-variant-structure.patch bcm27xx/patches-5.10/950-0565-drm-vc4-Correct-pixel-order-for-DSI0.patch bcm27xx/patches-5.10/950-0566-drm-vc4-Register-dsi0-as-the-correct-vc4-encoder-typ.patch bcm27xx/patches-5.10/950-0567-drm-vc4-Fix-dsi0-interrupt-support.patch bcm27xx/patches-5.10/950-0568-drm-vc4-Add-correct-stop-condition-to-vc4_dsi_encode.patch bcm27xx/patches-5.10/950-0647-drm-vc4-Fix-timings-for-interlaced-modes.patch bcm27xx/patches-5.10/950-0695-drm-vc4-Fix-margin-calculations-for-the-right-bottom.patch Upstream sets the pixel clock to 340MHz now, do not set it to 600MHz any more. bcm27xx/patches-5.10/950-0576-drm-vc4-hdmi-Raise-the-maximum-clock-rate.patch Fixes:89956c6532
("kernel: bump 5.10 to 5.10.138") Fixes:4209c33ae2
("kernel: bump 5.10 to 5.10.137") Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
34 lines
1.1 KiB
Diff
34 lines
1.1 KiB
Diff
--- a/drivers/tty/serial/8250/8250.h
|
|
+++ b/drivers/tty/serial/8250/8250.h
|
|
@@ -82,6 +82,7 @@ struct serial8250_config {
|
|
#define UART_CAP_MINI (1 << 17) /* Mini UART on BCM283X family lacks:
|
|
* STOP PARITY EPAR SPAR WLEN5 WLEN6
|
|
*/
|
|
+#define UART_CAP_NMOD (1 << 18) /* UART doesn't do termios */
|
|
|
|
#define UART_BUG_QUOT (1 << 0) /* UART has buggy quot LSB */
|
|
#define UART_BUG_TXEN (1 << 1) /* UART has buggy TX IIR status */
|
|
--- a/drivers/tty/serial/8250/8250_port.c
|
|
+++ b/drivers/tty/serial/8250/8250_port.c
|
|
@@ -288,7 +288,7 @@ static const struct serial8250_config ua
|
|
.tx_loadsz = 16,
|
|
.fcr = UART_FCR_ENABLE_FIFO |
|
|
UART_FCR_CLEAR_RCVR | UART_FCR_CLEAR_XMIT,
|
|
- .flags = UART_CAP_FIFO,
|
|
+ .flags = UART_CAP_FIFO | UART_CAP_NMOD,
|
|
},
|
|
[PORT_NPCM] = {
|
|
.name = "Nuvoton 16550",
|
|
@@ -2716,6 +2716,11 @@ serial8250_do_set_termios(struct uart_po
|
|
unsigned long flags;
|
|
unsigned int baud, quot, frac = 0;
|
|
|
|
+ if (up->capabilities & UART_CAP_NMOD) {
|
|
+ termios->c_cflag = 0;
|
|
+ return;
|
|
+ }
|
|
+
|
|
if (up->capabilities & UART_CAP_MINI) {
|
|
termios->c_cflag &= ~(CSTOPB | PARENB | PARODD | CMSPAR);
|
|
if ((termios->c_cflag & CSIZE) == CS5 ||
|