ExternalVendorCode/openwrt
1
0
Fork 0
mirror of https://github.com/openwrt/openwrt.git synced 2024-12-20 14:13:16 +00:00
Code Issues Actions 4 Packages Projects Releases Wiki Activity
22caf30a65
openwrt/target/linux/ath79/image/generic.mk
Michael Pratt 22caf30a65 ath79: add support for Senao Engenius ENH202 v1 
FCC ID: U2M-ENH200

Engenius ENH202 is an outdoor wireless access point with 2 10/100 ports,
built-in ethernet switch, internal antenna plates and proprietery PoE.

Specification:

  - Qualcomm/Atheros AR7240 rev 2
  - 40 MHz reference clock
  - 8 MB FLASH                  ST25P64V6P (aka ST M25P64)
  - 32 MB RAM
  - UART at J3                  (populated)
  - 2x 10/100 Mbps Ethernet     (built-in switch at gmac1)
  - 2.4 GHz, 2x2, 29dBm         (Atheros AR9280 rev 2)
  - internal antenna plates     (10 dbi, semi-directional)
  - 5 LEDs, 1 button            (LAN, WAN, RSSI) (Reset)

Known Issues:

  - Sysupgrade from ar71xx no longer possible
  - Power LED not controllable, or unknown gpio

MAC addresses:

  eth0/eth1  *:11   art 0x0/0x6
  wlan       *:10   art 0x120c

  The device label lists both addresses, WLAN MAC and ETH MAC,
  in that order.

  Since 0x0 and 0x6 have the same content, it cannot be
  determined which is eth0 and eth1, so we chose 0x0 for both.

Installation:

  2 ways to flash factory.bin from OEM:

  - Connect ethernet directly to board (the non POE port)
      this is LAN for all images
  - if you get Failsafe Mode from failed flash:
      only use it to flash Original firmware from Engenius
      or risk kernel loop or halt which requires serial cable

  Method 1: Firmware upgrade page:

    OEM webpage at 192.168.1.1
    username and password "admin"
    In upper right select Reset
    "Restore to factory default settings"
    Wait for reboot and login again
    Navigate to "Firmware Upgrade" page from left pane
    Click Browse and select the factory.bin image
    Upload and verify checksum
    Click Continue to confirm and wait 3 minutes

  Method 2: Serial to load Failsafe webpage:

    After connecting to serial console and rebooting...
    Interrupt boot with any key pressed rapidly
    execute `run failsafe_boot` OR `bootm 0x9f670000`
    wait a minute
    connect to ethernet and navigate to
    "192.168.1.1/index.htm"
    Select the factory.bin image and upload
    wait about 3 minutes

Return to OEM:

  If you have a serial cable, see Serial Failsafe instructions

  *DISCLAIMER*
  The Failsafe image is unique to Engenius boards.
  If the failsafe image is missing or damaged this will not work
  DO NOT downgrade to ar71xx this way, can cause kernel loop or halt

  The easiest way to return to the OEM software is the Failsafe image
  If you dont have a serial cable, you can ssh into openwrt and run

  `mtd -r erase fakeroot`

  Wait 3 minutes
  connect to ethernet and navigate to 192.168.1.1/index.htm
  select OEM firmware image from Engenius and click upgrade

Format of OEM firmware image:

  The OEM software of ENH202 is a heavily modified version
  of Openwrt Kamikaze bleeding-edge. One of the many modifications
  is to the sysupgrade program. Image verification is performed
  simply by the successful ungzip and untar of the supplied file
  and name check and header verification of the resulting contents.
  To form a factory.bin that is accepted by OEM Openwrt build,
  the kernel and rootfs must have specific names...

    openwrt-senao-enh202-uImage-lzma.bin
    openwrt-senao-enh202-root.squashfs

  and begin with the respective headers (uImage, squashfs).
  Then the files must be tarballed and gzipped.
  The resulting binary is actually a tar.gz file in disguise.
  This can be verified by using binwalk on the OEM firmware images,
  ungzipping then untaring, and by swapping headers to see
  what the OEM upgrade utility accepts and rejects.

  OKLI kernel loader is required because the OEM firmware
  expects the kernel to be no greater than 1024k
  and the factory.bin upgrade procedure would otherwise
  overwrite part of the kernel when writing rootfs.

Note on built-in switch:

  ENH202 is originally configured to be an access point,
  but with two ethernet ports, both WAN and LAN is possible.

  the POE port is gmac0 which is preferred to be
  the port for WAN because it gives link status
  where swconfig does not.

Signed-off-by: Michael Pratt <mpratt51@gmail.com>
[assign label_mac in 02_network, use ucidef_set_interface_wan,
use common device definition, some reordering]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-08-31 17:41:21 +02:00

1610 lines
46 KiB
Makefile
Raw Blame History

include ./common-buffalo.mk
include ./common-netgear.mk
include ./common-tp-link.mk
include ./common-yuncore.mk
DEVICE_VARS += ADDPATTERN_ID ADDPATTERN_VERSION
DEVICE_VARS += SEAMA_SIGNATURE SEAMA_MTDBLOCK
DEVICE_VARS += KERNEL_INITRAMFS_PREFIX
DEVICE_VARS += DAP_SIGNATURE ENGENIUS_IMGNAME
define Build/add-elecom-factory-initramfs
$(eval edimax_model=$(word 1,$(1)))
$(eval product=$(word 2,$(1)))
$(STAGING_DIR_HOST)/bin/mkedimaximg \
-b -s CSYS -m $(edimax_model) \
-f 0x70000 -S 0x01100000 \
-i $@ -o $@.factory
( \
echo -n -e "ELECOM\x00\x00$(product)" | dd bs=40 count=1 conv=sync; \
echo -n "0.00" | dd bs=16 count=1 conv=sync; \
dd if=$@.factory; \
) > $@.factory.new
if [ "$$(stat -c%s $@.factory.new)" -le $$(($(subst k,* 1024,$(subst m, * 1024k,$(IMAGE_SIZE))))) ]; then \
mv $@.factory.new $(BIN_DIR)/$(KERNEL_INITRAMFS_PREFIX)-factory.bin; \
else \
echo "WARNING: initramfs kernel image too big, cannot generate factory image" >&2; \
fi
endef
define Build/addpattern
-$(STAGING_DIR_HOST)/bin/addpattern -B $(ADDPATTERN_ID) \
-v v$(ADDPATTERN_VERSION) -i $@ -o $@.new
-mv "$@.new" "$@"
endef
define Build/append-md5sum-bin
$(STAGING_DIR_HOST)/bin/mkhash md5 $@ | sed 's/../\\\\x&/g' |\
xargs echo -ne >> $@
endef
define Build/cybertan-trx
@echo -n '' > $@-empty.bin
-$(STAGING_DIR_HOST)/bin/trx -o $@.new \
-f $(IMAGE_KERNEL) -F $@-empty.bin \
-x 32 -a 0x10000 -x -32 -f $@
-mv "$@.new" "$@"
-rm $@-empty.bin
endef
# This needs to make /tmp/_sys/sysupgrade.tgz an empty file prior to
# sysupgrade, as otherwise it will implant the old configuration from
# OEM firmware when writing rootfs from factory.bin
define Build/engenius-tar-gz
-[ -f "$@" ] && \
mkdir -p $@.tmp && \
echo '#!/bin/sh' > $@.tmp/before-upgrade.sh && \
echo ': > /tmp/_sys/sysupgrade.tgz' >> $@.tmp/before-upgrade.sh && \
$(CP) $(KDIR)/loader-$(DEVICE_NAME).uImage \
$@.tmp/openwrt-$(word 1,$(1))-uImage-lzma.bin && \
$(CP) $@ $@.tmp/openwrt-$(word 1,$(1))-root.squashfs && \
$(TAR) -cp --numeric-owner --owner=0 --group=0 --mode=a-s --sort=name \
$(if $(SOURCE_DATE_EPOCH),--mtime="@$(SOURCE_DATE_EPOCH)") \
-C $@.tmp . | gzip -9n > $@ && \
rm -rf $@.tmp
endef
define Build/mkdapimg2
$(STAGING_DIR_HOST)/bin/mkdapimg2 \
-i $@ -o $@.new \
-s $(DAP_SIGNATURE) \
-v $(VERSION_DIST)-$(firstword $(subst +, , \
$(firstword $(subst -, ,$(REVISION))))) \
-r Default \
$(if $(1),-k $(1))
mv $@.new $@
endef
define Build/mkmylofw_16m
$(eval device_id=$(word 1,$(1)))
$(eval revision=$(word 2,$(1)))
# On WPJ344, WPJ531, and WPJ563, the default boot command tries 0x9f680000
# first and fails if the remains of the stock image are sill there
# - resulting in an infinite boot loop.
# The size parameter is grown to have that block deleted if the firmware
# isn't big enough by itself.
let \
size="$$(stat -c%s $@)" \
pad="$(subst k,* 1024,$(BLOCKSIZE))" \
pad="(pad - (size % pad)) % pad" \
newsize='size + pad' ; \
[ $$newsize -lt $$((0x660000)) ] && newsize=0x660000 ; \
$(STAGING_DIR_HOST)/bin/mkmylofw \
-B WPE72 -i 0x11f6:$(device_id):0x11f6:$(device_id) -r $(revision) \
-s 0x1000000 -p0x30000:$$newsize:al:0x80060000:"OpenWRT":$@ \
$@.new
@mv $@.new $@
endef
define Build/mkwrggimg
$(STAGING_DIR_HOST)/bin/mkwrggimg -b \
-i $@ -o $@.imghdr -d /dev/mtdblock/1 \
-m $(DEVICE_MODEL)-$(DEVICE_VARIANT) -s $(DAP_SIGNATURE) \
-v $(VERSION_DIST) -B $(REVISION)
mv $@.imghdr $@
endef
define Build/nec-enc
$(STAGING_DIR_HOST)/bin/nec-enc \
-i $@ -o $@.new -k $(1)
mv $@.new $@
endef
define Build/nec-fw
( stat -c%s $@ | tr -d "\n" | dd bs=16 count=1 conv=sync; ) >> $@
( \
echo -n -e "$(1)" | dd bs=16 count=1 conv=sync; \
echo -n "0.0.00" | dd bs=16 count=1 conv=sync; \
dd if=$@; \
) > $@.new
mv $@.new $@
endef
define Build/pisen_wmb001n-factory
-[ -f "$@" ] && \
mkdir -p "$@.tmp" && \
cp "$(KDIR)/loader-$(word 1,$(1)).uImage" "$@.tmp/uImage" && \
mv "$@" "$@.tmp/rootfs" && \
cp "bin/pisen_wmb001n_factory-header.bin" "$@" && \
$(TAR) -cp --numeric-owner --owner=0 --group=0 --mode=a-s --sort=name \
$(if $(SOURCE_DATE_EPOCH),--mtime="@$(SOURCE_DATE_EPOCH)") \
-C "$@.tmp" . | gzip -9n >> "$@" && \
rm -rf "$@.tmp"
endef
define Build/teltonika-fw-fake-checksum
# Teltonika U-Boot web based firmware upgrade/recovery routine compares
# 16 bytes from md5sum1[16] field in TP-Link v1 header (offset: 76 bytes
# from begin of the firmware file) with 16 bytes stored just before
# 0xdeadc0de marker. Values are only compared, MD5 sum is not verified.
let \
offs="$$(stat -c%s $@) - 20"; \
dd if=$@ bs=1 count=16 skip=76 |\
dd of=$@ bs=1 count=16 seek=$$offs conv=notrunc
endef
define Build/wrgg-pad-rootfs
$(STAGING_DIR_HOST)/bin/padjffs2 $(IMAGE_ROOTFS) -c 64 >>$@
endef
define Device/seama
KERNEL := kernel-bin | append-dtb | relocate-kernel | lzma
KERNEL_INITRAMFS := $$(KERNEL) | seama
IMAGES += factory.bin
SEAMA_MTDBLOCK := 1
# 64 bytes offset:
# - 28 bytes seama_header
# - 36 bytes of META data (4-bytes aligned)
IMAGE/default := append-kernel | pad-offset $$$$(BLOCKSIZE) 64 | append-rootfs
IMAGE/sysupgrade.bin := $$(IMAGE/default) | seama | pad-rootfs | \
append-metadata | check-size
IMAGE/factory.bin := $$(IMAGE/default) | pad-rootfs -x 64 | seama | \
seama-seal | check-size
SEAMA_SIGNATURE :=
endef
define Device/8dev_carambola2
SOC := ar9331
DEVICE_VENDOR := 8devices
DEVICE_MODEL := Carambola2
DEVICE_PACKAGES := kmod-usb2 kmod-usb-chipidea2
IMAGE_SIZE := 16000k
SUPPORTED_DEVICES += carambola2
endef
TARGET_DEVICES += 8dev_carambola2
define Device/8dev_lima
SOC := qca9531
DEVICE_VENDOR := 8devices
DEVICE_MODEL := Lima
DEVICE_PACKAGES := kmod-usb2
IMAGE_SIZE := 15616k
SUPPORTED_DEVICES += lima
endef
TARGET_DEVICES += 8dev_lima
define Device/adtran_bsap1880
SOC := ar7161
DEVICE_VENDOR := Adtran/Bluesocket
DEVICE_PACKAGES += -swconfig -uboot-envtools fconfig
KERNEL := kernel-bin | append-dtb | lzma | pad-to $$(BLOCKSIZE)
KERNEL_INITRAMFS := kernel-bin | append-dtb
IMAGE_SIZE := 11200k
IMAGES += kernel.bin rootfs.bin
IMAGE/kernel.bin := append-kernel
IMAGE/rootfs.bin := append-rootfs | pad-rootfs
IMAGE/sysupgrade.bin := append-rootfs | pad-rootfs | \
check-size | sysupgrade-tar rootfs=$$$$@ | append-metadata
endef
define Device/adtran_bsap1800-v2
$(Device/adtran_bsap1880)
DEVICE_MODEL := BSAP-1800
DEVICE_VARIANT := v2
endef
TARGET_DEVICES += adtran_bsap1800-v2
define Device/adtran_bsap1840
$(Device/adtran_bsap1880)
DEVICE_MODEL := BSAP-1840
endef
TARGET_DEVICES += adtran_bsap1840
define Device/alfa-network_ap121f
SOC := ar9331
DEVICE_VENDOR := ALFA Network
DEVICE_MODEL := AP121F
DEVICE_PACKAGES := kmod-usb2 kmod-usb-chipidea2 kmod-usb-storage -swconfig
IMAGE_SIZE := 16064k
SUPPORTED_DEVICES += ap121f
endef
TARGET_DEVICES += alfa-network_ap121f
define Device/allnet_all-wap02860ac
SOC := qca9558
DEVICE_VENDOR := ALLNET
DEVICE_MODEL := ALL-WAP02860AC
DEVICE_PACKAGES := ath10k-firmware-qca988x-ct kmod-ath10k-ct
IMAGE_SIZE := 13120k
endef
TARGET_DEVICES += allnet_all-wap02860ac
define Device/arduino_yun
SOC := ar9331
DEVICE_VENDOR := Arduino
DEVICE_MODEL := Yun
DEVICE_PACKAGES := kmod-usb2 kmod-usb-chipidea2 kmod-usb-ledtrig-usbport \
kmod-usb-storage block-mount -swconfig
IMAGE_SIZE := 15936k
SUPPORTED_DEVICES += arduino-yun
endef
TARGET_DEVICES += arduino_yun
define Device/aruba_ap-105
SOC := ar7161
DEVICE_VENDOR := Aruba
DEVICE_MODEL := AP-105
IMAGE_SIZE := 16000k
DEVICE_PACKAGES := kmod-i2c-gpio kmod-tpm-i2c-atmel
endef
TARGET_DEVICES += aruba_ap-105
define Device/avm
DEVICE_VENDOR := AVM
KERNEL := kernel-bin | append-dtb | lzma | eva-image
KERNEL_INITRAMFS := $$(KERNEL)
IMAGE/sysupgrade.bin := append-kernel | pad-to 64k | \
append-squashfs-fakeroot-be | pad-to 256 | append-rootfs | pad-rootfs | \
append-metadata | check-size
DEVICE_PACKAGES := fritz-tffs
endef
define Device/avm_fritz1750e
$(Device/avm)
SOC := qca9556
IMAGE_SIZE := 15232k
DEVICE_MODEL := FRITZ!WLAN Repeater 1750E
DEVICE_PACKAGES += rssileds kmod-ath10k-ct-smallbuffers \
ath10k-firmware-qca988x-ct -swconfig
endef
TARGET_DEVICES += avm_fritz1750e
define Device/avm_fritz300e
$(Device/avm)
SOC := ar7242
IMAGE_SIZE := 15232k
DEVICE_MODEL := FRITZ!WLAN Repeater 300E
DEVICE_PACKAGES += rssileds -swconfig
SUPPORTED_DEVICES += fritz300e
endef
TARGET_DEVICES += avm_fritz300e
define Device/avm_fritz4020
$(Device/avm)
SOC := qca9561
IMAGE_SIZE := 15232k
DEVICE_MODEL := FRITZ!Box 4020
SUPPORTED_DEVICES += fritz4020
endef
TARGET_DEVICES += avm_fritz4020
define Device/avm_fritz450e
$(Device/avm)
SOC := qca9556
IMAGE_SIZE := 15232k
DEVICE_MODEL := FRITZ!WLAN Repeater 450E
SUPPORTED_DEVICES += fritz450e
endef
TARGET_DEVICES += avm_fritz450e
define Device/avm_fritzdvbc
$(Device/avm)
SOC := qca9556
IMAGE_SIZE := 15232k
DEVICE_MODEL := FRITZ!WLAN Repeater DVB-C
DEVICE_PACKAGES += rssileds kmod-ath10k-ct-smallbuffers \
ath10k-firmware-qca988x-ct -swconfig
endef
TARGET_DEVICES += avm_fritzdvbc
define Device/buffalo_bhr-4grv
SOC := ar7242
DEVICE_VENDOR := Buffalo
DEVICE_MODEL := BHR-4GRV
DEVICE_PACKAGES := kmod-usb2 kmod-usb-ledtrig-usbport
IMAGE_SIZE := 32256k
IMAGES += factory.bin tftp.bin
IMAGE/default := append-kernel | pad-to $$$$(BLOCKSIZE) | append-rootfs | \
pad-rootfs | check-size
IMAGE/factory.bin := $$(IMAGE/default) | buffalo-enc BHR-4GRV 1.99 | \
buffalo-tag BHR-4GRV 3
IMAGE/tftp.bin := $$(IMAGE/default) | buffalo-tftp-header
SUPPORTED_DEVICES += wzr-hp-g450h
endef
TARGET_DEVICES += buffalo_bhr-4grv
define Device/buffalo_bhr-4grv2
SOC := qca9557
DEVICE_VENDOR := Buffalo
DEVICE_MODEL := BHR-4GRV2
IMAGE_SIZE := 16000k
endef
TARGET_DEVICES += buffalo_bhr-4grv2
define Device/buffalo_wzr-hp-ag300h
SOC := ar7161
DEVICE_VENDOR := Buffalo
DEVICE_MODEL := WZR-HP-AG300H
IMAGE_SIZE := 32320k
IMAGES += factory.bin tftp.bin
IMAGE/default := append-kernel | pad-to $$$$(BLOCKSIZE) | append-rootfs | \
pad-rootfs | check-size
IMAGE/factory.bin := $$(IMAGE/default) | buffalo-enc WZR-HP-AG300H 1.99 | \
buffalo-tag WZR-HP-AG300H 3
IMAGE/tftp.bin := $$(IMAGE/default) | buffalo-tftp-header
DEVICE_PACKAGES := kmod-usb-ohci kmod-usb2 kmod-usb-ledtrig-usbport \
kmod-leds-reset kmod-owl-loader
SUPPORTED_DEVICES += wzr-hp-ag300h
endef
TARGET_DEVICES += buffalo_wzr-hp-ag300h
define Device/buffalo_wzr-hp-g302h-a1a0
SOC := ar7242
DEVICE_VENDOR := Buffalo
DEVICE_MODEL := WZR-HP-G302H
DEVICE_VARIANT := A1A0
DEVICE_PACKAGES := kmod-usb2 kmod-usb-ledtrig-usbport
IMAGE_SIZE := 32128k
IMAGES += factory.bin tftp.bin
IMAGE/default := append-kernel | pad-to $$$$(BLOCKSIZE) | append-rootfs | \
pad-rootfs | check-size
IMAGE/factory.bin := $$(IMAGE/default) | buffalo-enc WZR-HP-G302H 1.99 | \
buffalo-tag WZR-HP-G302H 4
IMAGE/tftp.bin := $$(IMAGE/default) | buffalo-tftp-header
SUPPORTED_DEVICES += wzr-hp-g300nh2
endef
TARGET_DEVICES += buffalo_wzr-hp-g302h-a1a0
define Device/buffalo_wzr-hp-g450h
SOC := ar7242
DEVICE_VENDOR := Buffalo
DEVICE_MODEL := WZR-HP-G450H/WZR-450HP
DEVICE_PACKAGES := kmod-usb2 kmod-usb-ledtrig-usbport
IMAGE_SIZE := 32256k
IMAGES += factory.bin tftp.bin
IMAGE/default := append-kernel | pad-to $$$$(BLOCKSIZE) | append-rootfs | \
pad-rootfs | check-size
IMAGE/factory.bin := $$(IMAGE/default) | buffalo-enc WZR-HP-G450H 1.99 | \
buffalo-tag WZR-HP-G450H 3
IMAGE/tftp.bin := $$(IMAGE/default) | buffalo-tftp-header
SUPPORTED_DEVICES += wzr-hp-g450h
endef
TARGET_DEVICES += buffalo_wzr-hp-g450h
define Device/comfast_cf-e110n-v2
SOC := qca9533
DEVICE_VENDOR := COMFAST
DEVICE_MODEL := CF-E110N
DEVICE_VARIANT := v2
DEVICE_PACKAGES := rssileds -swconfig -uboot-envtools
IMAGE_SIZE := 16192k
endef
TARGET_DEVICES += comfast_cf-e110n-v2
define Device/comfast_cf-e120a-v3
SOC := ar9344
DEVICE_VENDOR := COMFAST
DEVICE_MODEL := CF-E120A
DEVICE_VARIANT := v3
DEVICE_PACKAGES := rssileds -uboot-envtools
IMAGE_SIZE := 8000k
endef
TARGET_DEVICES += comfast_cf-e120a-v3
define Device/comfast_cf-e130n-v2
SOC := qca9531
DEVICE_VENDOR := COMFAST
DEVICE_MODEL := CF-E130N
DEVICE_VARIANT := v2
DEVICE_PACKAGES := rssileds -swconfig -uboot-envtools
IMAGE_SIZE := 7936k
endef
TARGET_DEVICES += comfast_cf-e130n-v2
define Device/comfast_cf-e313ac
SOC := qca9531
DEVICE_VENDOR := COMFAST
DEVICE_MODEL := CF-E313AC
DEVICE_PACKAGES := rssileds kmod-ath10k-ct-smallbuffers \
ath10k-firmware-qca9888-ct -swconfig -uboot-envtools
IMAGE_SIZE := 7936k
endef
TARGET_DEVICES += comfast_cf-e313ac
define Device/comfast_cf-e314n-v2
SOC := qca9531
DEVICE_VENDOR := COMFAST
DEVICE_MODEL := CF-E314N
DEVICE_VARIANT := v2
DEVICE_PACKAGES := rssileds
IMAGE_SIZE := 7936k
endef
TARGET_DEVICES += comfast_cf-e314n-v2
define Device/comfast_cf-e5
SOC := qca9531
DEVICE_VENDOR := COMFAST
DEVICE_MODEL := CF-E5/E7
DEVICE_PACKAGES := rssileds kmod-usb2 kmod-usb-net-qmi-wwan -swconfig \
-uboot-envtools
IMAGE_SIZE := 16192k
endef
TARGET_DEVICES += comfast_cf-e5
define Device/comfast_cf-e560ac
SOC := qca9531
DEVICE_VENDOR := COMFAST
DEVICE_MODEL := CF-E560AC
DEVICE_PACKAGES := kmod-usb2 kmod-ath10k-ct ath10k-firmware-qca9888-ct
IMAGE_SIZE := 16128k
endef
TARGET_DEVICES += comfast_cf-e560ac
define Device/comfast_cf-ew72
SOC := qca9531
DEVICE_VENDOR := COMFAST
DEVICE_MODEL := CF-EW72
DEVICE_PACKAGES := kmod-usb2 kmod-ath10k-ct ath10k-firmware-qca9888-ct \
-uboot-envtools -swconfig
IMAGE_SIZE := 16192k
endef
TARGET_DEVICES += comfast_cf-ew72
define Device/comfast_cf-wr650ac-v1
SOC := qca9558
DEVICE_VENDOR := COMFAST
DEVICE_MODEL := CF-WR650AC
DEVICE_VARIANT := v1
DEVICE_PACKAGES := kmod-ath10k-ct ath10k-firmware-qca988x-ct
IMAGE_SIZE := 16128k
endef
TARGET_DEVICES += comfast_cf-wr650ac-v1
define Device/comfast_cf-wr650ac-v2
SOC := qca9558
DEVICE_VENDOR := COMFAST
DEVICE_MODEL := CF-WR650AC
DEVICE_VARIANT := v2
DEVICE_PACKAGES := kmod-ath10k-ct ath10k-firmware-qca988x-ct
IMAGE_SIZE := 16000k
endef
TARGET_DEVICES += comfast_cf-wr650ac-v2
define Device/comfast_cf-wr752ac-v1
SOC := qca9531
DEVICE_VENDOR := COMFAST
DEVICE_MODEL := CF-WR752AC
DEVICE_VARIANT := v1
DEVICE_PACKAGES := kmod-usb2 kmod-ath10k-ct ath10k-firmware-qca9888-ct \
-uboot-envtools
IMAGE_SIZE := 16192k
endef
TARGET_DEVICES += comfast_cf-wr752ac-v1
define Device/compex_wpj344-16m
SOC := ar9344
DEVICE_PACKAGES := kmod-usb2
IMAGE_SIZE := 16128k
DEVICE_VENDOR := Compex
DEVICE_MODEL := WPJ344
DEVICE_VARIANT := 16M
SUPPORTED_DEVICES += wpj344
IMAGES += cpximg-6a08.bin
IMAGE/cpximg-6a08.bin := append-kernel | pad-to $$$$(BLOCKSIZE) | append-rootfs | pad-rootfs | mkmylofw_16m 0x690 3
endef
TARGET_DEVICES += compex_wpj344-16m
define Device/compex_wpj531-16m
SOC := qca9531
DEVICE_PACKAGES := kmod-usb2
IMAGE_SIZE := 16128k
DEVICE_VENDOR := Compex
DEVICE_MODEL := WPJ531
DEVICE_VARIANT := 16M
SUPPORTED_DEVICES += wpj531
IMAGES += cpximg-7a03.bin cpximg-7a04.bin cpximg-7a06.bin cpximg-7a07.bin
IMAGE/cpximg-7a03.bin := append-kernel | pad-to $$$$(BLOCKSIZE) | append-rootfs | pad-rootfs | mkmylofw_16m 0x68a 2
IMAGE/cpximg-7a04.bin := append-kernel | pad-to $$$$(BLOCKSIZE) | append-rootfs | pad-rootfs | mkmylofw_16m 0x693 3
IMAGE/cpximg-7a06.bin := append-kernel | pad-to $$$$(BLOCKSIZE) | append-rootfs | pad-rootfs | mkmylofw_16m 0x693 3
IMAGE/cpximg-7a07.bin := append-kernel | pad-to $$$$(BLOCKSIZE) | append-rootfs | pad-rootfs | mkmylofw_16m 0x693 3
endef
TARGET_DEVICES += compex_wpj531-16m
define Device/compex_wpj563
SOC := qca9563
DEVICE_PACKAGES := kmod-usb2 kmod-usb3
IMAGE_SIZE := 16128k
DEVICE_VENDOR := Compex
DEVICE_MODEL := WPJ563
SUPPORTED_DEVICES += wpj563
IMAGES += cpximg-7a02.bin
IMAGE/cpximg-7a02.bin := append-kernel | pad-to $$$$(BLOCKSIZE) | append-rootfs | pad-rootfs | mkmylofw_16m 0x694 2
endef
TARGET_DEVICES += compex_wpj563
define Device/devolo_dvl1200e
SOC := qca9558
DEVICE_VENDOR := devolo
DEVICE_MODEL := WiFi pro 1200e
DEVICE_PACKAGES := kmod-ath10k-ct ath10k-firmware-qca988x-ct
IMAGE_SIZE := 15936k
endef
TARGET_DEVICES += devolo_dvl1200e
define Device/devolo_dvl1200i
SOC := qca9558
DEVICE_VENDOR := devolo
DEVICE_MODEL := WiFi pro 1200i
DEVICE_PACKAGES := kmod-ath10k-ct ath10k-firmware-qca988x-ct
IMAGE_SIZE := 15936k
endef
TARGET_DEVICES += devolo_dvl1200i
define Device/devolo_dvl1750c
SOC := qca9558
DEVICE_VENDOR := devolo
DEVICE_MODEL := WiFi pro 1750c
DEVICE_PACKAGES := kmod-ath10k-ct ath10k-firmware-qca988x-ct
IMAGE_SIZE := 15936k
endef
TARGET_DEVICES += devolo_dvl1750c
define Device/devolo_dvl1750e
SOC := qca9558
DEVICE_VENDOR := devolo
DEVICE_MODEL := WiFi pro 1750e
DEVICE_PACKAGES := kmod-usb2 kmod-ath10k-ct ath10k-firmware-qca988x-ct
IMAGE_SIZE := 15936k
endef
TARGET_DEVICES += devolo_dvl1750e
define Device/devolo_dvl1750i
SOC := qca9558
DEVICE_VENDOR := devolo
DEVICE_MODEL := WiFi pro 1750i
DEVICE_PACKAGES := kmod-ath10k-ct ath10k-firmware-qca988x-ct
IMAGE_SIZE := 15936k
endef
TARGET_DEVICES += devolo_dvl1750i
define Device/devolo_dvl1750x
SOC := qca9558
DEVICE_VENDOR := devolo
DEVICE_MODEL := WiFi pro 1750x
DEVICE_PACKAGES := kmod-ath10k-ct ath10k-firmware-qca988x-ct
IMAGE_SIZE := 15936k
endef
TARGET_DEVICES += devolo_dvl1750x
define Device/devolo_magic-2-wifi
SOC := ar9344
DEVICE_VENDOR := Devolo
DEVICE_MODEL := Magic 2 WiFi
DEVICE_PACKAGES := kmod-ath10k-ct ath10k-firmware-qca988x-ct
IMAGE_SIZE := 15872k
endef
TARGET_DEVICES += devolo_magic-2-wifi
define Device/dlink_dap-13xx
SOC := qca9533
DEVICE_VENDOR := D-Link
DEVICE_PACKAGES += rssileds
IMAGE_SIZE := 7936k
IMAGES += factory.bin
IMAGE/factory.bin := append-kernel | pad-to $$$$(BLOCKSIZE) | \
append-rootfs | pad-rootfs | check-size | mkdapimg2 0xE0000
endef
define Device/dlink_dap-1330-a1
$(Device/dlink_dap-13xx)
DEVICE_MODEL := DAP-1330
DEVICE_VARIANT := A1
DAP_SIGNATURE := HONEYBEE-FIRMWARE-DAP-1330
SUPPORTED_DEVICES += dap-1330-a1
endef
TARGET_DEVICES += dlink_dap-1330-a1
define Device/dlink_dap-1365-a1
$(Device/dlink_dap-13xx)
DEVICE_MODEL := DAP-1365
DEVICE_VARIANT := A1
DAP_SIGNATURE := HONEYBEE-FIRMWARE-DAP-1365
endef
TARGET_DEVICES += dlink_dap-1365-a1
define Device/dlink_dap-2695-a1
SOC := qca9558
DEVICE_PACKAGES := ath10k-firmware-qca988x-ct kmod-ath10k-ct
DEVICE_VENDOR := D-Link
DEVICE_MODEL := DAP-2965
DEVICE_VARIANT := A1
IMAGES := factory.img sysupgrade.bin
IMAGE_SIZE := 15360k
IMAGE/default := append-kernel | pad-offset 65536 160
IMAGE/factory.img := $$(IMAGE/default) | append-rootfs | wrgg-pad-rootfs | \
mkwrggimg | check-size
IMAGE/sysupgrade.bin := $$(IMAGE/default) | mkwrggimg | append-rootfs | \
wrgg-pad-rootfs | append-metadata | check-size
KERNEL := kernel-bin | append-dtb | relocate-kernel | lzma
KERNEL_INITRAMFS := $$(KERNEL) | mkwrggimg
DAP_SIGNATURE := wapac02_dkbs_dap2695
SUPPORTED_DEVICES += dap-2695-a1
endef
TARGET_DEVICES += dlink_dap-2695-a1
define Device/dlink_dch-g020-a1
SOC := qca9531
DEVICE_VENDOR := D-Link
DEVICE_MODEL := DCH-G020
DEVICE_VARIANT := A1
DEVICE_PACKAGES := kmod-gpio-pca953x kmod-i2c-gpio kmod-usb2 kmod-usb-acm
IMAGES += factory.bin
IMAGE_SIZE := 14784k
IMAGE/factory.bin := append-kernel | pad-to $$$$(BLOCKSIZE) | \
append-rootfs | pad-rootfs | check-size | mkdapimg2 0x20000
DAP_SIGNATURE := HONEYBEE-FIRMWARE-DCH-G020
endef
TARGET_DEVICES += dlink_dch-g020-a1
define Device/dlink_dir-505
SOC := ar9330
DEVICE_VENDOR := D-Link
DEVICE_MODEL := DIR-505
IMAGE_SIZE := 7680k
DEVICE_PACKAGES := kmod-usb2
SUPPORTED_DEVICES += dir-505-a1
endef
TARGET_DEVICES += dlink_dir-505
define Device/dlink_dir-825-b1
SOC := ar7161
DEVICE_VENDOR := D-Link
DEVICE_MODEL := DIR-825
DEVICE_VARIANT := B1
IMAGE_SIZE := 6208k
IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | \
append-metadata | check-size
DEVICE_PACKAGES := kmod-usb-ohci kmod-usb2 kmod-usb-ledtrig-usbport \
kmod-leds-reset kmod-owl-loader
SUPPORTED_DEVICES += dir-825-b1
endef
TARGET_DEVICES += dlink_dir-825-b1
define Device/dlink_dir-825-c1
SOC := ar9344
DEVICE_VENDOR := D-Link
DEVICE_MODEL := DIR-825
DEVICE_VARIANT := C1
DEVICE_PACKAGES := kmod-usb2 kmod-usb-ledtrig-usbport kmod-leds-reset \
kmod-owl-loader
SUPPORTED_DEVICES += dir-825-c1
IMAGE_SIZE := 15936k
IMAGES := factory.bin sysupgrade.bin
IMAGE/default := append-kernel | pad-to $$$$(BLOCKSIZE) | append-rootfs | \
pad-rootfs
IMAGE/factory.bin := $$(IMAGE/default) | pad-offset $$$$(IMAGE_SIZE) 26 | \
append-string 00DB120AR9344-RT-101214-00 | check-size
IMAGE/sysupgrade.bin := $$(IMAGE/default) | append-metadata | \
check-size
endef
TARGET_DEVICES += dlink_dir-825-c1
define Device/dlink_dir-835-a1
SOC := ar9344
DEVICE_VENDOR := D-Link
DEVICE_MODEL := DIR-835
DEVICE_VARIANT := A1
DEVICE_PACKAGES := kmod-usb2 kmod-leds-reset kmod-owl-loader
SUPPORTED_DEVICES += dir-835-a1
IMAGE_SIZE := 15936k
IMAGES := factory.bin sysupgrade.bin
IMAGE/default := append-kernel | pad-to $$$$(BLOCKSIZE) | append-rootfs | \
pad-rootfs
IMAGE/factory.bin := $$(IMAGE/default) | pad-offset $$$$(IMAGE_SIZE) 26 | \
append-string 00DB120AR9344-RT-101214-00 | check-size
IMAGE/sysupgrade.bin := $$(IMAGE/default) | append-metadata | \
check-size
endef
TARGET_DEVICES += dlink_dir-835-a1
define Device/dlink_dir-842-c
SOC := qca9563
DEVICE_VENDOR := D-Link
DEVICE_MODEL := DIR-842
KERNEL := kernel-bin | append-dtb | relocate-kernel | lzma
KERNEL_INITRAMFS := $$(KERNEL) | seama
IMAGES += factory.bin
SEAMA_MTDBLOCK := 5
SEAMA_SIGNATURE := wrgac65_dlink.2015_dir842
# 64 bytes offset:
# - 28 bytes seama_header
# - 36 bytes of META data (4-bytes aligned)
IMAGE/default := append-kernel | uImage lzma | \
pad-offset $$$$(BLOCKSIZE) 64 | append-rootfs
IMAGE/sysupgrade.bin := $$(IMAGE/default) | seama | pad-rootfs | \
append-metadata | check-size
IMAGE/factory.bin := $$(IMAGE/default) | pad-rootfs -x 64 | seama | \
seama-seal | check-size
IMAGE_SIZE := 15680k
endef
define Device/dlink_dir-842-c1
$(Device/dlink_dir-842-c)
DEVICE_VARIANT := C1
DEVICE_PACKAGES := kmod-ath10k-ct ath10k-firmware-qca9888-ct
endef
TARGET_DEVICES += dlink_dir-842-c1
define Device/dlink_dir-842-c2
$(Device/dlink_dir-842-c)
DEVICE_VARIANT := C2
DEVICE_PACKAGES := kmod-usb2 kmod-ath10k-ct ath10k-firmware-qca9888-ct
endef
TARGET_DEVICES += dlink_dir-842-c2
define Device/dlink_dir-842-c3
$(Device/dlink_dir-842-c)
DEVICE_VARIANT := C3
DEVICE_PACKAGES := kmod-ath10k-ct ath10k-firmware-qca9888-ct
endef
TARGET_DEVICES += dlink_dir-842-c3
define Device/dlink_dir-859-a1
$(Device/seama)
SOC := qca9563
DEVICE_VENDOR := D-Link
DEVICE_MODEL := DIR-859
DEVICE_VARIANT := A1
IMAGE_SIZE := 15872k
DEVICE_PACKAGES := kmod-usb2 kmod-ath10k-ct-smallbuffers ath10k-firmware-qca988x-ct
SEAMA_SIGNATURE := wrgac37_dlink.2013gui_dir859
endef
TARGET_DEVICES += dlink_dir-859-a1
define Device/elecom_wrc-1750ghbk2-i
SOC := qca9563
DEVICE_VENDOR := ELECOM
DEVICE_MODEL := WRC-1750GHBK2-I/C
IMAGE_SIZE := 15808k
KERNEL_INITRAMFS := $$(KERNEL) | pad-to 2 | \
add-elecom-factory-initramfs RN68 WRC-1750GHBK2
DEVICE_PACKAGES := kmod-ath10k-ct ath10k-firmware-qca988x-ct
endef
TARGET_DEVICES += elecom_wrc-1750ghbk2-i
define Device/elecom_wrc-300ghbk2-i
SOC := qca9563
DEVICE_VENDOR := ELECOM
DEVICE_MODEL := WRC-300GHBK2-I
IMAGE_SIZE := 7616k
KERNEL_INITRAMFS := $$(KERNEL) | pad-to 2 | \
add-elecom-factory-initramfs RN51 WRC-300GHBK2-I
endef
TARGET_DEVICES += elecom_wrc-300ghbk2-i
define Device/embeddedwireless_dorin
SOC := ar9331
DEVICE_VENDOR := Embedded Wireless
DEVICE_MODEL := Dorin
DEVICE_PACKAGES := kmod-usb-chipidea2
IMAGE_SIZE := 16000k
endef
TARGET_DEVICES += embeddedwireless_dorin
define Device/engenius_ecb1750
SOC := qca9558
DEVICE_VENDOR := EnGenius
DEVICE_MODEL := ECB1750
DEVICE_PACKAGES := kmod-ath10k-ct ath10k-firmware-qca988x-ct
IMAGE_SIZE := 15680k
IMAGE/factory.bin := append-kernel | pad-to $$$$(BLOCKSIZE) | \
append-rootfs | pad-rootfs | check-size | \
senao-header -r 0x101 -p 0x6d -t 2
IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | \
append-metadata | check-size
endef
TARGET_DEVICES += engenius_ecb1750
define Device/engenius_loader_okli
DEVICE_VENDOR := EnGenius
KERNEL := kernel-bin | append-dtb | lzma | uImage lzma -M 0x4f4b4c49
LOADER_TYPE := bin
COMPILE := loader-$(1).bin loader-$(1).uImage
COMPILE/loader-$(1).bin := loader-okli-compile
COMPILE/loader-$(1).uImage := append-loader-okli $(1) | pad-to 64k | lzma | \
uImage lzma
IMAGES += factory.bin
IMAGE/factory.bin := append-squashfs-fakeroot-be | pad-to $$$$(BLOCKSIZE) | \
append-kernel | pad-to $$$$(BLOCKSIZE) | append-rootfs | pad-rootfs | \
check-size | engenius-tar-gz $$$$(ENGENIUS_IMGNAME)
endef
define Device/engenius_enh202-v1
$(Device/engenius_loader_okli)
SOC := ar7240
DEVICE_MODEL := ENH202
DEVICE_VARIANT := v1
DEVICE_PACKAGES := rssileds
IMAGE_SIZE := 4864k
LOADER_FLASH_OFFS := 0x1b0000
ENGENIUS_IMGNAME := senao-enh202
endef
TARGET_DEVICES += engenius_enh202-v1
define Device/engenius_ens202ext-v1
$(Device/engenius_loader_okli)
SOC := ar9341
DEVICE_MODEL := ENS202EXT
DEVICE_VARIANT := v1
DEVICE_PACKAGES := rssileds
IMAGE_SIZE := 12032k
LOADER_FLASH_OFFS := 0x230000
ENGENIUS_IMGNAME := senao-ens202ext
endef
TARGET_DEVICES += engenius_ens202ext-v1
define Device/engenius_epg5000
SOC := qca9558
DEVICE_VENDOR := EnGenius
DEVICE_MODEL := EPG5000
DEVICE_PACKAGES := ath10k-firmware-qca988x-ct kmod-ath10k-ct kmod-usb2
IMAGE_SIZE := 14656k
IMAGES += factory.dlf
IMAGE/factory.dlf := append-kernel | pad-to $$$$(BLOCKSIZE) | \
append-rootfs | pad-rootfs | check-size | \
senao-header -r 0x101 -p 0x71 -t 2
SUPPORTED_DEVICES += epg5000
endef
TARGET_DEVICES += engenius_epg5000
define Device/engenius_ews511ap
SOC := qca9531
DEVICE_VENDOR := EnGenius
DEVICE_MODEL := EWS511AP
DEVICE_PACKAGES := kmod-ath10k-ct ath10k-firmware-qca9887-ct
IMAGE_SIZE := 16000k
endef
TARGET_DEVICES += engenius_ews511ap
define Device/enterasys_ws-ap3705i
SOC := ar9344
DEVICE_VENDOR := Enterasys
DEVICE_MODEL := WS-AP3705i
IMAGE_SIZE := 30528k
endef
TARGET_DEVICES += enterasys_ws-ap3705i
define Device/etactica_eg200
SOC := ar9331
DEVICE_VENDOR := eTactica
DEVICE_MODEL := EG200
DEVICE_PACKAGES := kmod-usb-chipidea2 kmod-ledtrig-oneshot \
kmod-usb-serial kmod-usb-serial-ftdi kmod-usb-storage kmod-fs-ext4
IMAGE_SIZE := 16000k
SUPPORTED_DEVICES += rme-eg200
endef
TARGET_DEVICES += etactica_eg200
define Device/glinet_6408
$(Device/tplink-8mlzma)
SOC := ar9331
DEVICE_VENDOR := GL.iNet
DEVICE_MODEL := 6408
DEVICE_PACKAGES := kmod-usb2
IMAGE_SIZE := 8000k
TPLINK_HWID := 0x08000001
IMAGES := sysupgrade.bin
SUPPORTED_DEVICES += gl-inet
endef
TARGET_DEVICES += glinet_6408
define Device/glinet_6416
$(Device/tplink-16mlzma)
SOC := ar9331
DEVICE_VENDOR := GL.iNet
DEVICE_MODEL := 6416
DEVICE_PACKAGES := kmod-usb2
IMAGE_SIZE := 16192k
TPLINK_HWID := 0x08000001
IMAGES := sysupgrade.bin
SUPPORTED_DEVICES += gl-inet
endef
TARGET_DEVICES += glinet_6416
define Device/glinet_gl-ar150
SOC := ar9330
DEVICE_VENDOR := GL.iNet
DEVICE_MODEL := GL-AR150
DEVICE_PACKAGES := kmod-usb-chipidea2
IMAGE_SIZE := 16000k
SUPPORTED_DEVICES += gl-ar150
endef
TARGET_DEVICES += glinet_gl-ar150
define Device/glinet_gl-ar300m-common-nor
SOC := qca9531
DEVICE_VENDOR := GL.iNet
DEVICE_PACKAGES := kmod-usb2
IMAGE_SIZE := 16000k
SUPPORTED_DEVICES += gl-ar300m
endef
define Device/glinet_gl-ar300m-lite
$(Device/glinet_gl-ar300m-common-nor)
DEVICE_MODEL := GL-AR300M
DEVICE_VARIANT := Lite
endef
TARGET_DEVICES += glinet_gl-ar300m-lite
define Device/glinet_gl-ar300m16
$(Device/glinet_gl-ar300m-common-nor)
DEVICE_MODEL := GL-AR300M16
endef
TARGET_DEVICES += glinet_gl-ar300m16
define Device/glinet_gl-ar750
SOC := qca9531
DEVICE_VENDOR := GL.iNet
DEVICE_MODEL := GL-AR750
DEVICE_PACKAGES := kmod-usb2 kmod-ath10k-ct ath10k-firmware-qca9887-ct
IMAGE_SIZE := 16000k
SUPPORTED_DEVICES += gl-ar750
endef
TARGET_DEVICES += glinet_gl-ar750
define Device/glinet_gl-mifi
SOC := ar9331
DEVICE_VENDOR := GL.iNET
DEVICE_MODEL := GL-MiFi
DEVICE_PACKAGES := kmod-usb-chipidea2
IMAGE_SIZE := 16000k
SUPPORTED_DEVICES += gl-mifi
endef
TARGET_DEVICES += glinet_gl-mifi
define Device/glinet_gl-x750
SOC := qca9531
DEVICE_VENDOR := GL.iNet
DEVICE_MODEL := GL-X750
DEVICE_PACKAGES := kmod-usb2 kmod-ath10k-ct ath10k-firmware-qca9887-ct
IMAGE_SIZE := 16000k
endef
TARGET_DEVICES += glinet_gl-x750
define Device/iodata_etg3-r
SOC := ar9342
DEVICE_VENDOR := I-O DATA
DEVICE_MODEL := ETG3-R
IMAGE_SIZE := 7680k
DEVICE_PACKAGES := -iwinfo -kmod-ath9k -wpad-basic-wolfssl
endef
TARGET_DEVICES += iodata_etg3-r
define Device/iodata_wn-ac1167dgr
SOC := qca9557
DEVICE_VENDOR := I-O DATA
DEVICE_MODEL := WN-AC1167DGR
IMAGE_SIZE := 14656k
IMAGES += factory.bin
IMAGE/factory.bin := append-kernel | pad-to $$$$(BLOCKSIZE) | \
append-rootfs | pad-rootfs | check-size | \
senao-header -r 0x30a -p 0x61 -t 2
DEVICE_PACKAGES := kmod-usb2 kmod-ath10k-ct ath10k-firmware-qca988x-ct
endef
TARGET_DEVICES += iodata_wn-ac1167dgr
define Device/iodata_wn-ac1600dgr
SOC := qca9557
DEVICE_VENDOR := I-O DATA
DEVICE_MODEL := WN-AC1600DGR
IMAGE_SIZE := 14656k
IMAGES += factory.bin
IMAGE/factory.bin := append-kernel | pad-to $$$$(BLOCKSIZE) | \
append-rootfs | pad-rootfs | check-size | \
senao-header -r 0x30a -p 0x60 -t 2 -v 200
DEVICE_PACKAGES := kmod-usb2 kmod-ath10k-ct ath10k-firmware-qca988x-ct
endef
TARGET_DEVICES += iodata_wn-ac1600dgr
define Device/iodata_wn-ac1600dgr2
SOC := qca9557
DEVICE_VENDOR := I-O DATA
DEVICE_MODEL := WN-AC1600DGR2/DGR3
IMAGE_SIZE := 14656k
IMAGES += dgr2-dgr3-factory.bin
IMAGE/dgr2-dgr3-factory.bin := append-kernel | pad-to $$$$(BLOCKSIZE) | \
append-rootfs | pad-rootfs | check-size | \
senao-header -r 0x30a -p 0x60 -t 2 -v 200
DEVICE_PACKAGES := kmod-usb2 kmod-ath10k-ct ath10k-firmware-qca988x-ct
endef
TARGET_DEVICES += iodata_wn-ac1600dgr2
define Device/iodata_wn-ag300dgr
SOC := ar1022
DEVICE_VENDOR := I-O DATA
DEVICE_MODEL := WN-AG300DGR
IMAGE_SIZE := 15424k
IMAGES += factory.bin
IMAGE/factory.bin := append-kernel | pad-to $$$$(BLOCKSIZE) | \
append-rootfs | pad-rootfs | check-size | \
senao-header -r 0x30a -p 0x47 -t 2
DEVICE_PACKAGES := kmod-usb2
endef
TARGET_DEVICES += iodata_wn-ag300dgr
define Device/jjplus_ja76pf2
SOC := ar7161
DEVICE_VENDOR := jjPlus
DEVICE_MODEL := JA76PF2
DEVICE_PACKAGES += -kmod-ath9k -swconfig -wpad-basic-wolfssl -uboot-envtools fconfig
IMAGES := kernel.bin rootfs.bin
IMAGE/kernel.bin := append-kernel
IMAGE/rootfs.bin := append-rootfs | pad-rootfs
KERNEL := kernel-bin | append-dtb | lzma | pad-to $$(BLOCKSIZE)
KERNEL_INITRAMFS := kernel-bin | append-dtb
IMAGE_SIZE := 16000k
SUPPORTED_DEVICES += ja76pf2
endef
TARGET_DEVICES += jjplus_ja76pf2
define Device/librerouter_librerouter-v1
SOC := qca9558
DEVICE_VENDOR := Librerouter
DEVICE_MODEL := LibreRouter
DEVICE_VARIANT := v1
IMAGE_SIZE := 7936k
DEVICE_PACKAGES := kmod-usb2
endef
TARGET_DEVICES += librerouter_librerouter-v1
define Device/meraki_mr16
SOC := ar7161
DEVICE_VENDOR := Meraki
DEVICE_MODEL := MR16
IMAGE_SIZE := 15616k
DEVICE_PACKAGES := kmod-owl-loader
SUPPORTED_DEVICES += mr16
DEVICE_COMPAT_VERSION := 2.0
DEVICE_COMPAT_MESSAGE := Partitions differ from ar71xx version of MR16. Image format is incompatible. \
To use sysupgrade, you must change /lib/update/common.sh::get_image to prepend 128K zeroes to this image, \
and change the bootcmd in u-boot to "bootm 0xbf0a0000". After that, you can use "sysupgrade -F". \
For more details, see the OpenWrt Wiki: https://openwrt.org/toh/meraki/mr16, \
or the commit message of the MR16 ath79 port on git.openwrt.org.
endef
TARGET_DEVICES += meraki_mr16
define Device/nec_wg1200cr
SOC := qca9563
DEVICE_VENDOR := NEC
DEVICE_MODEL := Aterm WG1200CR
IMAGE_SIZE := 7616k
SEAMA_MTDBLOCK := 6
SEAMA_SIGNATURE := wrgac72_necpf.2016gui_wg1200cr
IMAGES += factory.bin
IMAGE/default := append-kernel | pad-offset $$$$(BLOCKSIZE) 64 | append-rootfs
IMAGE/sysupgrade.bin := $$(IMAGE/default) | seama | pad-rootfs | \
append-metadata | check-size
IMAGE/factory.bin := $$(IMAGE/default) | pad-rootfs -x 64 | seama | \
seama-seal | nec-enc 9gsiy9nzep452pad | check-size
DEVICE_PACKAGES := kmod-ath10k-ct ath10k-firmware-qca9888-ct
endef
TARGET_DEVICES += nec_wg1200cr
define Device/nec_wg800hp
SOC := qca9563
DEVICE_VENDOR := NEC
DEVICE_MODEL := Aterm WG800HP
IMAGE_SIZE := 7104k
IMAGES += factory.bin
IMAGE/factory.bin := append-kernel | pad-to $$$$(BLOCKSIZE) | \
append-rootfs | pad-rootfs | check-size | \
xor-image -p 6A57190601121E4C004C1E1201061957 -x | nec-fw LASER_ATERM
DEVICE_PACKAGES := kmod-ath10k-ct-smallbuffers ath10k-firmware-qca9887-ct-full-htt
endef
TARGET_DEVICES += nec_wg800hp
define Device/netgear_ex6400_ex7300
$(Device/netgear_generic)
SOC := qca9558
NETGEAR_KERNEL_MAGIC := 0x27051956
NETGEAR_BOARD_ID := EX7300series
NETGEAR_HW_ID := 29765104+16+0+128
IMAGE_SIZE := 15552k
IMAGE/default := append-kernel | pad-offset $$$$(BLOCKSIZE) 64 | \
netgear-rootfs | pad-rootfs
IMAGE/sysupgrade.bin := $$(IMAGE/default) | append-metadata | \
check-size
IMAGE/factory.img := $$(IMAGE/default) | netgear-dni | \
check-size
DEVICE_PACKAGES := kmod-ath10k-ct ath10k-firmware-qca99x0-ct
endef
define Device/netgear_ex6400
$(Device/netgear_ex6400_ex7300)
DEVICE_MODEL := EX6400
endef
TARGET_DEVICES += netgear_ex6400
define Device/netgear_ex7300
$(Device/netgear_ex6400_ex7300)
DEVICE_MODEL := EX7300
endef
TARGET_DEVICES += netgear_ex7300
define Device/netgear_wndr3x00
$(Device/netgear_generic)
SOC := ar7161
DEVICE_PACKAGES := kmod-usb-ohci kmod-usb2 kmod-usb-ledtrig-usbport \
kmod-leds-reset kmod-owl-loader
endef
define Device/netgear_wndr3700
$(Device/netgear_wndr3x00)
DEVICE_MODEL := WNDR3700
DEVICE_VARIANT := v1
NETGEAR_KERNEL_MAGIC := 0x33373030
NETGEAR_BOARD_ID := WNDR3700
IMAGE_SIZE := 7680k
IMAGES += factory-NA.img
IMAGE/factory-NA.img := $$(IMAGE/default) | netgear-dni NA | \
check-size
SUPPORTED_DEVICES += wndr3700
endef
TARGET_DEVICES += netgear_wndr3700
define Device/netgear_wndr3700-v2
$(Device/netgear_wndr3x00)
DEVICE_MODEL := WNDR3700
DEVICE_VARIANT := v2
NETGEAR_KERNEL_MAGIC := 0x33373031
NETGEAR_BOARD_ID := WNDR3700v2
NETGEAR_HW_ID := 29763654+16+64
IMAGE_SIZE := 15872k
SUPPORTED_DEVICES += wndr3700 netgear,wndr3700v2
endef
TARGET_DEVICES += netgear_wndr3700-v2
define Device/netgear_wndr3800
$(Device/netgear_wndr3x00)
DEVICE_MODEL := WNDR3800
NETGEAR_KERNEL_MAGIC := 0x33373031
NETGEAR_BOARD_ID := WNDR3800
NETGEAR_HW_ID := 29763654+16+128
IMAGE_SIZE := 15872k
SUPPORTED_DEVICES += wndr3700
endef
TARGET_DEVICES += netgear_wndr3800
define Device/netgear_wndr3800ch
$(Device/netgear_wndr3x00)
DEVICE_MODEL := WNDR3800CH
NETGEAR_KERNEL_MAGIC := 0x33373031
NETGEAR_BOARD_ID := WNDR3800CH
NETGEAR_HW_ID := 29763654+16+128
IMAGE_SIZE := 15872k
SUPPORTED_DEVICES += wndr3700
endef
TARGET_DEVICES += netgear_wndr3800ch
define Device/netgear_wndrmac-v1
$(Device/netgear_wndr3x00)
DEVICE_MODEL := WNDRMAC
DEVICE_VARIANT := v1
NETGEAR_KERNEL_MAGIC := 0x33373031
NETGEAR_BOARD_ID := WNDRMAC
NETGEAR_HW_ID := 29763654+16+64
IMAGE_SIZE := 15872k
SUPPORTED_DEVICES += wndr3700
endef
TARGET_DEVICES += netgear_wndrmac-v1
define Device/netgear_wndrmac-v2
$(Device/netgear_wndr3x00)
DEVICE_MODEL := WNDRMAC
DEVICE_VARIANT := v2
NETGEAR_KERNEL_MAGIC := 0x33373031
NETGEAR_BOARD_ID := WNDRMACv2
NETGEAR_HW_ID := 29763654+16+128
IMAGE_SIZE := 15872k
SUPPORTED_DEVICES += wndr3700
endef
TARGET_DEVICES += netgear_wndrmac-v2
define Device/netgear_wnr2200_common
$(Device/netgear_generic)
SOC := ar7241
DEVICE_MODEL := WNR2200
DEVICE_PACKAGES := kmod-usb2 kmod-usb-ledtrig-usbport
NETGEAR_KERNEL_MAGIC := 0x32323030
NETGEAR_BOARD_ID := wnr2200
endef
define Device/netgear_wnr2200-8m
$(Device/netgear_wnr2200_common)
DEVICE_VARIANT := 8M
NETGEAR_HW_ID := 29763600+08+64
IMAGE_SIZE := 7808k
IMAGES += factory-NA.img
IMAGE/factory-NA.img := $$(IMAGE/default) | netgear-dni NA | \
check-size
SUPPORTED_DEVICES += wnr2200
endef
TARGET_DEVICES += netgear_wnr2200-8m
define Device/netgear_wnr2200-16m
$(Device/netgear_wnr2200_common)
DEVICE_VARIANT := 16M
DEVICE_ALT0_VENDOR := NETGEAR
DEVICE_ALT0_MODEL := WNR2200
DEVICE_ALT0_VARIANT := CN/RU
NETGEAR_HW_ID :=
IMAGE_SIZE := 16000k
endef
TARGET_DEVICES += netgear_wnr2200-16m
define Device/ocedo_koala
SOC := qca9558
DEVICE_VENDOR := Ocedo
DEVICE_MODEL := Koala
DEVICE_PACKAGES := kmod-ath10k-ct ath10k-firmware-qca988x-ct
SUPPORTED_DEVICES += koala
IMAGE_SIZE := 7424k
IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | \
append-metadata | check-size
endef
TARGET_DEVICES += ocedo_koala
define Device/ocedo_raccoon
SOC := ar9344
DEVICE_VENDOR := Ocedo
DEVICE_MODEL := Raccoon
IMAGE_SIZE := 7424k
IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | \
append-metadata | check-size
endef
TARGET_DEVICES += ocedo_raccoon
define Device/ocedo_ursus
SOC := qca9558
DEVICE_VENDOR := Ocedo
DEVICE_MODEL := Ursus
DEVICE_PACKAGES := kmod-ath10k-ct ath10k-firmware-qca988x-ct
IMAGE_SIZE := 7424k
IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | \
append-metadata | check-size
endef
TARGET_DEVICES += ocedo_ursus
define Device/openmesh_om5p-ac-v2
SOC := qca9558
DEVICE_VENDOR := OpenMesh
DEVICE_MODEL := OM5P-AC
DEVICE_VARIANT := v2
DEVICE_PACKAGES := kmod-ath10k-ct ath10k-firmware-qca988x-ct om-watchdog
IMAGE_SIZE := 7808k
SUPPORTED_DEVICES += om5p-acv2
endef
TARGET_DEVICES += openmesh_om5p-ac-v2
define Device/pcs_cap324
SOC := ar9344
DEVICE_VENDOR := PowerCloud Systems
DEVICE_MODEL := CAP324
IMAGE_SIZE := 16000k
SUPPORTED_DEVICES += cap324
endef
TARGET_DEVICES += pcs_cap324
define Device/pcs_cr3000
SOC := ar9341
DEVICE_VENDOR := PowerCloud Systems
DEVICE_MODEL := CR3000
IMAGE_SIZE := 7808k
SUPPORTED_DEVICES += cr3000
endef
TARGET_DEVICES += pcs_cr3000
define Device/pcs_cr5000
SOC := ar9344
DEVICE_VENDOR := PowerCloud Systems
DEVICE_MODEL := CR5000
DEVICE_PACKAGES := kmod-usb2
IMAGE_SIZE := 7808k
SUPPORTED_DEVICES += cr5000
endef
TARGET_DEVICES += pcs_cr5000
define Device/phicomm_k2t
SOC := qca9563
DEVICE_VENDOR := Phicomm
DEVICE_MODEL := K2T
IMAGE_SIZE := 15744k
IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | \
append-metadata | check-size
DEVICE_PACKAGES := kmod-leds-reset kmod-ath10k-ct-smallbuffers ath10k-firmware-qca9888-ct
endef
TARGET_DEVICES += phicomm_k2t
define Device/pisen_ts-d084
$(Device/tplink-8mlzma)
SOC := ar9331
DEVICE_VENDOR := PISEN
DEVICE_MODEL := TS-D084
DEVICE_PACKAGES := kmod-usb2 kmod-usb-chipidea2
TPLINK_HWID := 0x07030101
endef
TARGET_DEVICES += pisen_ts-d084
define Device/pisen_wmb001n
SOC := ar9341
DEVICE_VENDOR := PISEN
DEVICE_MODEL := WMB001N
IMAGE_SIZE := 14080k
DEVICE_PACKAGES := kmod-i2c-gpio kmod-usb2
LOADER_TYPE := bin
LOADER_FLASH_OFFS := 0x20000
COMPILE := loader-$(1).bin loader-$(1).uImage
COMPILE/loader-$(1).bin := loader-okli-compile
COMPILE/loader-$(1).uImage := append-loader-okli $(1) | pad-to 64k | lzma | \
uImage lzma
KERNEL := kernel-bin | append-dtb | lzma | uImage lzma -M 0x4f4b4c49
IMAGES += factory.bin
IMAGE/factory.bin := $$(IMAGE/sysupgrade.bin) | pisen_wmb001n-factory $(1)
endef
TARGET_DEVICES += pisen_wmb001n
define Device/pisen_wmm003n
$(Device/tplink-8mlzma)
SOC := ar9331
DEVICE_VENDOR := PISEN
DEVICE_MODEL := Cloud Easy Power (WMM003N)
DEVICE_PACKAGES := kmod-usb2 kmod-usb-chipidea2
TPLINK_HWID := 0x07030101
endef
TARGET_DEVICES += pisen_wmm003n
define Device/qihoo_c301
$(Device/seama)
SOC := ar9344
DEVICE_VENDOR := Qihoo
DEVICE_MODEL := C301
DEVICE_PACKAGES := kmod-usb2 kmod-ath10k-ct ath10k-firmware-qca988x-ct \
uboot-envtools
IMAGE_SIZE := 15744k
SEAMA_SIGNATURE := wrgac26_qihoo360_360rg
SUPPORTED_DEVICES += qihoo-c301
endef
TARGET_DEVICES += qihoo_c301
define Device/rosinson_wr818
SOC := qca9563
DEVICE_VENDOR := Rosinson
DEVICE_MODEL := WR818
IMAGE_SIZE := 15872k
DEVICE_PACKAGES := kmod-usb2 kmod-usb-ledtrig-usbport
endef
TARGET_DEVICES += rosinson_wr818
define Device/siemens_ws-ap3610
SOC := ar7161
DEVICE_VENDOR := Siemens
DEVICE_MODEL := WS-AP3610
IMAGE_SIZE := 14336k
BLOCKSIZE := 256k
LOADER_TYPE := bin
LOADER_FLASH_OFFS := 0x82000
COMPILE := loader-$(1).bin
COMPILE/loader-$(1).bin := loader-okli-compile
KERNEL := kernel-bin | append-dtb | lzma | uImage lzma -M 0x4f4b4c49 | loader-okli $(1) 8128 | uImage none
KERNEL_INITRAMFS := kernel-bin | append-dtb | uImage none
endef
TARGET_DEVICES += siemens_ws-ap3610
define Device/sitecom_wlr-7100
SOC := ar1022
DEVICE_VENDOR := Sitecom
DEVICE_MODEL := WLR-7100
DEVICE_VARIANT := v1 002
DEVICE_PACKAGES := ath10k-firmware-qca988x-ct kmod-ath10k-ct-smallbuffers kmod-usb2
IMAGES += factory.dlf
IMAGE/factory.dlf := append-kernel | pad-to $$$$(BLOCKSIZE) | \
append-rootfs | pad-rootfs | check-size | \
senao-header -r 0x222 -p 0x53 -t 2
IMAGE_SIZE := 7488k
endef
TARGET_DEVICES += sitecom_wlr-7100
define Device/sitecom_wlr-8100
SOC := qca9558
DEVICE_VENDOR := Sitecom
DEVICE_MODEL := WLR-8100
DEVICE_ALT0_VENDOR := Sitecom
DEVICE_ALT0_MODEL := X8 AC1750
DEVICE_PACKAGES := ath10k-firmware-qca988x-ct kmod-ath10k-ct kmod-usb2 kmod-usb3
SUPPORTED_DEVICES += wlr8100
IMAGES += factory.dlf
IMAGE/factory.dlf := append-kernel | pad-to $$$$(BLOCKSIZE) | \
append-rootfs | pad-rootfs | check-size | \
senao-header -r 0x222 -p 0x56 -t 2
IMAGE_SIZE := 15424k
endef
TARGET_DEVICES += sitecom_wlr-8100
define Device/telco_t1
SOC := qca9531
DEVICE_VENDOR := Telco
DEVICE_MODEL := T1
DEVICE_PACKAGES := kmod-usb2 kmod-usb-net-qmi-wwan \
kmod-usb-serial-option uqmi -swconfig -uboot-envtools
IMAGE_SIZE := 16192k
SUPPORTED_DEVICES += telco_electronics,tel-t1
endef
TARGET_DEVICES += telco_t1
define Device/teltonika_rut955
SOC := ar9344
DEVICE_VENDOR := Teltonika
DEVICE_MODEL := RUT955
DEVICE_PACKAGES := kmod-usb2 kmod-usb-acm kmod-usb-net-qmi-wwan \
kmod-usb-serial-option kmod-hwmon-mcp3021 uqmi -uboot-envtools
IMAGE_SIZE := 15552k
TPLINK_HWID := 0x35000001
TPLINK_HWREV := 0x1
TPLINK_HEADER_VERSION := 1
KERNEL := kernel-bin | append-dtb | lzma | tplink-v1-header
KERNEL_INITRAMFS := kernel-bin | append-dtb | lzma | uImage lzma
IMAGES += factory.bin
IMAGE/factory.bin := append-kernel | pad-to $$$$(BLOCKSIZE) | append-rootfs |\
pad-rootfs | teltonika-fw-fake-checksum | append-string master |\
append-md5sum-bin | check-size
IMAGE/sysupgrade.bin := append-kernel | pad-to $$$$(BLOCKSIZE) |\
append-rootfs | pad-rootfs | append-metadata |\
check-size
endef
TARGET_DEVICES += teltonika_rut955
define Device/teltonika_rut955-h7v3c0
$(Device/teltonika_rut955)
DEVICE_VARIANT := H7V3C0
endef
TARGET_DEVICES += teltonika_rut955-h7v3c0
define Device/trendnet_tew-823dru
SOC := qca9558
DEVICE_VENDOR := Trendnet
DEVICE_MODEL := TEW-823DRU
DEVICE_VARIANT := v1.0R
DEVICE_PACKAGES := kmod-usb2 kmod-ath10k-ct ath10k-firmware-qca988x-ct
SUPPORTED_DEVICES += tew-823dru
IMAGE_SIZE := 15296k
IMAGES := factory.bin sysupgrade.bin
IMAGE/default := append-kernel | pad-to $$$$(BLOCKSIZE) | append-rootfs | \
pad-rootfs
IMAGE/factory.bin := $$(IMAGE/default) | pad-offset $$$$(IMAGE_SIZE) 26 | \
append-string 00AP135AR9558-RT-131129-00 | check-size
IMAGE/sysupgrade.bin := $$(IMAGE/default) | append-metadata | \
check-size
endef
TARGET_DEVICES += trendnet_tew-823dru
define Device/wd_mynet-n750
$(Device/seama)
SOC := ar9344
DEVICE_VENDOR := Western Digital
DEVICE_MODEL := My Net N750
IMAGE_SIZE := 15872k
DEVICE_PACKAGES := kmod-usb2
SEAMA_SIGNATURE := wrgnd13_wd_av
SUPPORTED_DEVICES += mynet-n750
endef
TARGET_DEVICES += wd_mynet-n750
define Device/wd_mynet-wifi-rangeextender
SOC := ar9344
DEVICE_VENDOR := Western Digital
DEVICE_MODEL := My Net Wi-Fi Range Extender
DEVICE_PACKAGES := rssileds nvram -swconfig
IMAGE_SIZE := 7808k
ADDPATTERN_ID := mynet-rext
ADDPATTERN_VERSION := 1.00.01
IMAGE/sysupgrade.bin := append-rootfs | pad-rootfs | cybertan-trx | \
addpattern | append-metadata
SUPPORTED_DEVICES += mynet-rext
endef
TARGET_DEVICES += wd_mynet-wifi-rangeextender
define Device/winchannel_wb2000
SOC := ar9344
DEVICE_VENDOR := Winchannel
DEVICE_MODEL := WB2000
IMAGE_SIZE := 15872k
DEVICE_PACKAGES := kmod-i2c-gpio kmod-rtc-ds1307 kmod-usb2 \
kmod-usb-ledtrig-usbport
endef
TARGET_DEVICES += winchannel_wb2000
define Device/xiaomi_mi-router-4q
SOC := qca9561
DEVICE_VENDOR := Xiaomi
DEVICE_MODEL := Mi Router 4Q
IMAGE_SIZE := 14336k
endef
TARGET_DEVICES += xiaomi_mi-router-4q
define Device/yuncore_a770
SOC := qca9531
DEVICE_VENDOR := YunCore
DEVICE_MODEL := A770
DEVICE_PACKAGES := kmod-ath10k-ct ath10k-firmware-qca9887-ct
IMAGE_SIZE := 16000k
IMAGES += tftp.bin
IMAGE/tftp.bin := $$(IMAGE/sysupgrade.bin) | yuncore-tftp-header-16m
endef
TARGET_DEVICES += yuncore_a770
define Device/yuncore_a782
SOC := qca9563
DEVICE_VENDOR := YunCore
DEVICE_MODEL := A782
DEVICE_PACKAGES := kmod-ath10k-ct ath10k-firmware-qca9888-ct
IMAGE_SIZE := 16000k
IMAGES += tftp.bin
IMAGE/tftp.bin := $$(IMAGE/sysupgrade.bin) | yuncore-tftp-header-16m
endef
TARGET_DEVICES += yuncore_a782
define Device/yuncore_xd4200
SOC := qca9563
DEVICE_VENDOR := YunCore
DEVICE_MODEL := XD4200
DEVICE_PACKAGES := kmod-ath10k-ct ath10k-firmware-qca9888-ct
IMAGE_SIZE := 16000k
IMAGES += tftp.bin
IMAGE/tftp.bin := $$(IMAGE/sysupgrade.bin) | yuncore-tftp-header-16m
endef
TARGET_DEVICES += yuncore_xd4200
define Device/zbtlink_zbt-wd323
SOC := ar9344
DEVICE_VENDOR := ZBT
DEVICE_MODEL := WD323
IMAGE_SIZE := 16000k
DEVICE_PACKAGES := kmod-usb2 kmod-i2c-gpio kmod-rtc-pcf8563 \
kmod-usb-serial kmod-usb-serial-cp210x uqmi
endef
TARGET_DEVICES += zbtlink_zbt-wd323
define Device/zyxel_nbg6616
SOC := qca9557
DEVICE_VENDOR := ZyXEL
DEVICE_MODEL := NBG6616
DEVICE_PACKAGES := kmod-usb2 kmod-usb-ledtrig-usbport kmod-rtc-pcf8563 \
kmod-ath10k-ct ath10k-firmware-qca988x-ct
IMAGE_SIZE := 15232k
RAS_BOARD := NBG6616
RAS_ROOTFS_SIZE := 14464k
RAS_VERSION := "OpenWrt Linux-$(LINUX_VERSION)"
IMAGES += factory.bin
IMAGE/factory.bin := append-kernel | pad-to $$$$(BLOCKSIZE) | \
append-rootfs | pad-rootfs | pad-to 64k | check-size | zyxel-ras-image
SUPPORTED_DEVICES += nbg6616
endef
TARGET_DEVICES += zyxel_nbg6616
Reference in New Issue View Git Blame Copy Permalink