mirror of
https://github.com/openwrt/openwrt.git
synced 2024-12-20 22:23:27 +00:00
67ce9aedd6
This patch adds support for the Check Point L-50 from 600/1100 series routers. Specification: -CPU: Marvell Kirkwood 88F6281 1200MHz -RAM: 512MB -Flash: NAND 512MB -WiFi: mPCIe card based on Atheros AR9287 b/g/n -WAN: 1 Gigabit Port (Marvell 88E1116R PHY) -LAN: 9 Gigabit Ports (2x Marvell 88E6171(5+4)) -USB: 2x USB2.0 -Express card slot -SD card slot -Serial console: RJ-45 115200 8n1 -Unsupported DSL Known issues: -DSL not supported -Expresscard not tested Installation: Step one -> backup: make backup u-boot and env for revert stock posibility make backup dsl_mac_addr, dmz_mac_addr, eth1addr, ethaddr and all lanX_mac_addr Step two -> Use kwboot tool to upload openwrt u-boot to RAM: run kwboot: "kwboot -B 115200 /dev/ttyUSB0 -b u-boot.kwb -p -t" end start u-boot Step three -> Restore macs (e.g. below): setenv eth1addr 00:1C:XX:XX:XX:6C setenv ethaddr 00:1C:XX:XX:XX:6B setenv lan1_mac_addr 00:1C:XX:XX:XX:6C setenv lan2_mac_addr 00:1C:XX:XX:XX:6D setenv lan3_mac_addr 00:1C:XX:XX:XX:6E setenv lan4_mac_addr 00:1C:XX:XX:XX:6F setenv lan5_mac_addr 00:1C:XX:XX:XX:70 setenv lan6_mac_addr 00:1C:XX:XX:XX:71 setenv lan7_mac_addr 00:1C:XX:XX:XX:72 setenv lan8_mac_addr 00:1C:XX:XX:XX:73 setenv dmz_mac_addr 00:1C:XX:XX:XX:74 setenv dsl_mac_addr 00:1C:XX:XX:XX:75 Step four -> flash u-boot: mw 0x0800000 0xffff 0x100000 nand erase 0x0 100000 tftp 0x0800000 openwrt-kirkwood-l50-u-boot.kwb nand write 0x0800000 0x0 0x100000 saveenv Step five -> run initramfs image: tftpboot 0x02000000 openwrt.bin; bootm 0x02000000; Step six -> install sysupgrade OpenWrt image: copy to /tmp/ sysupgrade image run sysupgrade Back to stock: Restore original u-boot end env. Install factory image via stock u-boot. Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
37 lines
618 B
Bash
37 lines
618 B
Bash
#!/bin/sh
|
|
#
|
|
# Copyright (C) 2012-2014 OpenWrt.org
|
|
#
|
|
|
|
[ -e /etc/config/ubootenv ] && exit 0
|
|
|
|
touch /etc/config/ubootenv
|
|
|
|
. /lib/uboot-envtools.sh
|
|
. /lib/functions.sh
|
|
|
|
board=$(board_name)
|
|
|
|
case "$board" in
|
|
checkpoint,l-50|\
|
|
cloudengines,pogoe02|\
|
|
cloudengines,pogoplugv4|\
|
|
iom,ix2-200|\
|
|
linksys,viper|\
|
|
raidsonic,ib-nas62x0|\
|
|
seagate,dockstar|\
|
|
zyxel,nsa310b|\
|
|
zyxel,nsa310s|\
|
|
zyxel,nsa325)
|
|
ubootenv_add_uci_config "/dev/mtd1" "0x0" "0x20000" "0x20000"
|
|
;;
|
|
linksys,audi)
|
|
ubootenv_add_uci_config "/dev/mtd1" "0x0" "0x4000" "0x4000"
|
|
;;
|
|
esac
|
|
|
|
config_load ubootenv
|
|
config_foreach ubootenv_add_app_config ubootenv
|
|
|
|
exit 0
|