mirror of
https://github.com/openwrt/openwrt.git
synced 2024-12-22 23:12:32 +00:00
2090b8af0a
Hardware:
SOC: Qualcomm IPQ4018
RAM: 128 MB Nanya NT5CC64M16GP-DI
FLASH: 16 MB Macronix MX25L12805D
ETH: Qualcomm QCA8075 (4 Gigabit ports, 3xLAN, 1xWAN)
WLAN: Qualcomm IPQ4018 (2.4 & 5 Ghz)
BUTTON: Shared WPS/Reset button
LED: RGB Status/Power LED
SERIAL: Header J8 (UART, Left side of board). Numbered from
top to bottom:
(1) GND, (2) TX, (3) RX, (4) VCC (White triangle
next to it).
3.3v, 115200, 8N1
Tested/Working:
* Ethernet
* WiFi (2.4 and 5GHz)
* Status LED
* Reset Button (See note below)
Implementation notes:
* The shared WPS/Reset button is implemented as a Reset button
* I could not find a original firmware image to reverse engineer, meaning
currently it's not possible to flash OpenWrt through the Web GUI.
Installation (Through Serial console & TFTP):
1. Set your PC to fixed IP 192.168.1.12, Netmask 255.255.255.0, and connect to
one of the LAN ports
2. Rename the initramfs image to 'C0A8010B.img' and enable a TFTP server on
your pc, to serve the image
2. Connect to the router through serial (See connection properties above)
3. Hit a key during startup, to pause startup
4. type `setenv serverip 192.168.1.12`, to set the tftp server address
5. type `tftpboot`, to load the image from the laptop through tftp
6. type `bootm` to run the loaded image from memory
6. (If you want to return to stock firmware later, create an full MTD backup,
e.g. using instructions here https://openwrt.org/docs/guide-user/installation/generic.backup#create_full_mtd_backup)
7. Transfer the 'sysupgrade' OpenWrt firmware image from PC to router, e.g.:
`scp xxx-squashfs-sysupgrade.bin root@192.168.1.1:/tmp/upgrade.bin`
8. Run sysupgrade to permanently install OpenWrt to flash: `sysupgrade -n /tmp/upgrade.bin`
Revert to stock:
To revert to stock, you need the MTD backup from step 6 above:
1. Unpack the MTD backup archive
2. Transfer the 'firmware' partition image to the router (e.g. mtd8_firmware.backup)
3. On the router, do `mtd write mtd8_firmware.backup firmware`
Signed-off-by: Tom Brouwer <tombrouwer@outlook.com>
[removed BOARD_NAME, OpenWRT->OpenWrt, changed LED device name to board name]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
101 lines
3.1 KiB
Makefile
101 lines
3.1 KiB
Makefile
include $(TOPDIR)/rules.mk
|
|
include $(INCLUDE_DIR)/version.mk
|
|
|
|
PKG_NAME:=ipq-wifi
|
|
PKG_RELEASE:=1
|
|
PKG_FLAGS:=nonshared
|
|
|
|
include $(INCLUDE_DIR)/package.mk
|
|
|
|
define Build/Prepare
|
|
mkdir -p $(PKG_BUILD_DIR)
|
|
endef
|
|
|
|
define Build/Compile
|
|
endef
|
|
|
|
#
|
|
# This is intended to be used on an interim basis until device-specific
|
|
# board data for new devices is available through the upstream compilation
|
|
#
|
|
# Please send a mail with your device-specific board files upstream.
|
|
# You can find instructions and examples on the linux-wireless wiki:
|
|
# <https://wireless.wiki.kernel.org/en/users/drivers/ath10k/boardfiles>
|
|
#
|
|
|
|
ALLWIFIBOARDS:= \
|
|
aruba_ap-303 \
|
|
avm_fritzrepeater-1200 \
|
|
ezviz_cs-w3-wd1200g-eup \
|
|
linksys_ea8300 \
|
|
qxwlan_e2600ac
|
|
|
|
ALLWIFIPACKAGES:=$(foreach BOARD,$(ALLWIFIBOARDS),ipq-wifi-$(BOARD))
|
|
|
|
define Package/ipq-wifi-default
|
|
SUBMENU:=ath10k Board-Specific Overrides
|
|
SECTION:=firmware
|
|
CATEGORY:=Firmware
|
|
DEPENDS:=@TARGET_ipq40xx
|
|
TITLE:=Custom Board
|
|
endef
|
|
|
|
define ipq-wifi-install-one-to
|
|
$(INSTALL_DIR) $(2)/lib/firmware/ath10k/$(3)/
|
|
$(INSTALL_DATA) $(1) $(2)/lib/firmware/ath10k/$(3)/board-2.bin
|
|
endef
|
|
|
|
# Note: .bin deprecated; supports existing boards
|
|
|
|
define ipq-wifi-install-one
|
|
$(if $(filter $(suffix $(1)),.QCA4019 .qca4019 .bin),\
|
|
$(call ipq-wifi-install-one-to,$(1),$(2),QCA4019/hw1.0),\
|
|
$(if $(filter $(suffix $(1)),.QCA9888 .qca9888),\
|
|
$(call ipq-wifi-install-one-to,$(1),$(2),QCA9888/hw2.0),\
|
|
$(if $(filter $(suffix $(1)),.QCA9984 .qca9984),\
|
|
$(call ipq-wifi-install-one-to,$(1),$(2),QCA9984/hw1.0),\
|
|
$(error Unrecognized board-file suffix '$(suffix $(1))' for '$(1)')\
|
|
)))
|
|
|
|
endef
|
|
# Blank line required at end of above define due to foreach context
|
|
|
|
define generate-ipq-wifi-package
|
|
define Package/ipq-wifi-$(1)
|
|
$(call Package/ipq-wifi-default)
|
|
TITLE:=board-2.bin Overrides for $(2)
|
|
CONFLICTS:=$(PREV_BOARD)
|
|
endef
|
|
|
|
define Package/ipq-wifi-$(1)/description
|
|
The $(2) requires board-specific, reference ("cal") data
|
|
that is not yet present in the upstream wireless firmware distribution.
|
|
|
|
This package supplies board-2.bin file(s) that, in the interim,
|
|
overwrite those supplied by the ath10k-firmware-* packages.
|
|
|
|
This is package is only necessary for the $(2).
|
|
|
|
Do not install it for any other device!
|
|
endef
|
|
|
|
define Package/ipq-wifi-$(1)/install-overlay
|
|
$$$$(foreach IPQ_WIFI_BOARD_FILE,$$$$(wildcard board-$(1).*),\
|
|
$$$$(call ipq-wifi-install-one,$$$$(IPQ_WIFI_BOARD_FILE),$$(1)))
|
|
endef
|
|
|
|
PREV_BOARD+=ipq-wifi-$(1)
|
|
endef
|
|
|
|
# Add board name to ALLWIFIBOARDS
|
|
# Place files in this directory as board-<devicename>.<qca4019|qca9888|qca9984>
|
|
# Add $(eval $(call generate-ipq-wifi-package,<devicename>,<display name>))
|
|
|
|
$(eval $(call generate-ipq-wifi-package,aruba_ap-303,Aruba AP-303))
|
|
$(eval $(call generate-ipq-wifi-package,avm_fritzrepeater-1200,AVM FRITZRepeater 1200))
|
|
$(eval $(call generate-ipq-wifi-package,ezviz_cs-w3-wd1200g-eup,EZVIZ CS-W3-WD1200G EUP))
|
|
$(eval $(call generate-ipq-wifi-package,linksys_ea8300,Linksys EA8300))
|
|
$(eval $(call generate-ipq-wifi-package,qxwlan_e2600ac,Qxwlan E2600AC))
|
|
|
|
$(foreach PACKAGE,$(ALLWIFIPACKAGES),$(eval $(call BuildPackage,$(PACKAGE))))
|