openwrt/target/linux/ramips/dts/mt7621_tplink_archer-x6-v3.dtsi
Arınç ÜNAL 271456abd8 ramips: mt7621-dts: do not claim rgmii2 group as gpio for certain devices
These devices do not use rgmii2 as gpio, therefore remove rgmii2 pin group
from state-default. Remove overwriting the ethernet node for these devices.

Move claiming the rgmii2 group from mt7621_zyxel_nwa-ax.dtsi to
mt7621_zyxel_nwa50ax.dts as it's only the latter using rgmii2 pins as gpio.

Remove duplicate ethernet overwrite from mt7621_tplink_archer-x6-v3.dtsi.

Claim rgmii2 group as gpio on mt7621_bolt_arion.dts as it uses an rgmii2
pin, 26, as gpio.

Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
2022-08-20 22:56:12 +02:00

198 lines
3.1 KiB
Plaintext

// SPDX-License-Identifier: GPL-2.0-only
#include "mt7621.dtsi"
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/input/input.h>
/ {
aliases {
label-mac-device = &gmac0;
led-boot = &led_power;
led-failsafe = &led_power;
led-running = &led_power;
led-upgrade = &led_power;
};
chosen {
bootargs = "console=ttyS0,115200n8";
};
keys {
compatible = "gpio-keys";
wps {
label = "wps";
gpios = <&gpio 28 GPIO_ACTIVE_LOW>;
debounce-interval = <60>;
linux,code = <KEY_WPS_BUTTON>;
};
reset {
label = "reset";
gpios = <&gpio 8 GPIO_ACTIVE_LOW>;
debounce-interval = <60>;
linux,code = <KEY_RESTART>;
};
};
leds {
compatible = "gpio-leds";
led_power: power {
label = "green:power";
gpios = <&gpio 4 GPIO_ACTIVE_LOW>;
};
wan_orange {
label = "orange:wan";
gpios = <&gpio 14 GPIO_ACTIVE_LOW>;
};
lan {
label = "green:lan";
gpios = <&gpio 15 GPIO_ACTIVE_LOW>;
};
wifi5g {
label = "green:wifi5g";
gpios = <&gpio 16 GPIO_ACTIVE_LOW>;
linux,default-trigger = "phy1tpt";
};
wifi2g {
label = "green:wifi2g";
gpios = <&gpio 18 GPIO_ACTIVE_LOW>;
linux,default-trigger = "phy0tpt";
};
wan_green {
label = "green:wan";
gpios = <&gpio 45 GPIO_ACTIVE_LOW>;
};
};
};
&spi0 {
status = "okay";
flash@0 {
compatible = "jedec,spi-nor";
reg = <0>;
spi-max-frequency = <40000000>;
partitions {
compatible = "fixed-partitions";
#address-cells = <1>;
#size-cells = <1>;
partition@0 {
label = "u-boot";
reg = <0x0 0x40000>;
read-only;
};
partition@40000 {
label = "firmware";
compatible = "denx,uimage";
reg = <0x40000 0xf60000>;
};
config: partition@fa0000 {
label = "config";
reg = <0xfa0000 0x50000>;
read-only;
};
radio: partition@ff0000 {
label = "radio";
reg = <0xff0000 0x10000>;
read-only;
};
};
};
};
&state_default {
gpio {
groups = "i2c", "rgmii2", "uart2", "uart3", "jtag", "wdt";
function = "gpio";
};
};
&pcie {
status = "okay";
};
&pcie0 {
wifi@0,0 {
compatible = "mediatek,mt76";
reg = <0x0000 0 0 0 0>;
mediatek,mtd-eeprom = <&radio 0x0>;
nvmem-cells = <&macaddr_config_8>;
nvmem-cell-names = "mac-address";
mac-address-increment = <1>;
ieee80211-freq-limit = <2400000 2500000>;
};
};
&pcie1 {
wifi@0,0 {
compatible = "mediatek,mt76";
reg = <0x0000 0 0 0 0>;
mediatek,mtd-eeprom = <&radio 0x8000>;
nvmem-cells = <&macaddr_config_8>;
nvmem-cell-names = "mac-address";
mac-address-increment = <2>;
ieee80211-freq-limit = <5000000 6000000>;
};
};
&ethernet {
pinctrl-0 = <&mdio_pins>, <&rgmii1_pins>;
};
&gmac0 {
nvmem-cells = <&macaddr_config_8>;
nvmem-cell-names = "mac-address";
};
&switch0 {
ports {
port@0 {
status = "okay";
label = "wan";
};
port@1 {
status = "okay";
label = "lan1";
};
port@2 {
status = "okay";
label = "lan2";
};
port@3 {
status = "okay";
label = "lan3";
};
port@4 {
status = "okay";
label = "lan4";
};
};
};
&config {
compatible = "nvmem-cells";
#address-cells = <1>;
#size-cells = <1>;
macaddr_config_8: macaddr@8 {
reg = <0x8 0x6>;
};
};