openwrt/target/linux/ath79/dts/ar7242_tplink_tl-wr2543-v1.dts
Dmitry Tunin 7a873974f7 ath79: add support for indicating the boot state using multiple leds
Use diag.sh version used for apm821xx, ipq40xx and ipq806x, which
supports different leds for the different boot states.

The existing led sequences should be the same as before.

Signed-off-by: Dmitry Tunin <hanipouspilot@gmail.com>
[reword commit message]
Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-08-15 07:42:36 +02:00

185 lines
2.9 KiB
Plaintext

// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
/dts-v1/;
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/input/input.h>
#include "ar7242.dtsi"
/ {
compatible = "tplink,tl-wr2543-v1", "qca,ar7242";
model = "TP-LINK TL-WR2543N/ND";
aliases {
led-boot = &system;
led-failsafe = &system;
led-running = &system;
led-upgrade = &system;
};
chosen {
bootargs = "console=ttyS0,115200n8";
};
extosc: ref {
compatible = "fixed-clock";
#clock-cells = <0>;
clock-frequency = <40000000>;
};
gpio-keys {
compatible = "gpio-keys-polled";
poll-interval = <20>;
reset {
label = "reset";
linux,code = <KEY_RESTART>;
gpios = <&gpio 11 GPIO_ACTIVE_LOW>;
debounce-interval = <60>;
};
wps {
label = "wps";
linux,code = <KEY_WPS_BUTTON>;
gpios = <&gpio 12 GPIO_ACTIVE_LOW>;
debounce-interval = <60>;
};
};
leds {
compatible = "gpio-leds";
system: wps {
label = "tplink:green:wps";
gpios = <&gpio 0 GPIO_ACTIVE_LOW>;
default-state = "off";
};
usb {
label = "tplink:green:usb";
gpios = <&gpio 8 GPIO_ACTIVE_LOW>;
default-state = "off";
trigger-sources = <&hub_port>;
linux,default-trigger = "usbport";
};
};
ath9k-leds {
compatible = "gpio-leds";
wlan2g {
label = "tplink:green:wlan2g";
gpios = <&ath9k 0 GPIO_ACTIVE_LOW>;
default-state = "off";
linux,default-trigger = "phy0tpt";
};
wlan5g {
label = "tplink:green:wlan5g";
gpios = <&ath9k 1 GPIO_ACTIVE_LOW>;
default-state = "off";
linux,default-trigger = "phy0tpt";
};
};
rtl8367 {
compatible = "realtek,rtl8367";
gpio-sda = <&gpio 1 GPIO_ACTIVE_HIGH>;
gpio-sck = <&gpio 6 GPIO_ACTIVE_HIGH>;
realtek,extif0 = <1 0 1 1 1 1 1 1 2>;
mdio-bus {
#address-cells = <1>;
#size-cells = <0>;
status = "okay";
phy0: ethernet-phy@0 {
reg = <0>;
};
};
};
};
&pll {
clocks = <&extosc>;
};
&spi {
status = "okay";
num-cs = <1>;
flash@0 {
compatible = "jedec,spi-nor";
reg = <0>;
spi-max-frequency = <25000000>;
partitions {
compatible = "fixed-partitions";
#address-cells = <1>;
#size-cells = <1>;
uboot: partition@0 {
label = "u-boot";
reg = <0x000000 0x020000>;
read-only;
};
partition@20000 {
label = "firmware";
reg = <0x020000 0x7d0000>;
};
partition@7f0000 {
label = "art";
reg = <0x7f0000 0x010000>;
read-only;
};
};
};
};
&uart {
status = "okay";
};
&usb {
#address-cells = <1>;
#size-cells = <0>;
status = "okay";
hub_port: port@1 {
reg = <1>;
#trigger-source-cells = <0>;
};
};
&usb_phy {
status = "okay";
};
&pcie {
status = "okay";
ath9k: wifi@0,0 {
reg = <0x0000 0 0 0 0>;
#gpio-cells = <2>;
gpio-controller;
qca,no-eeprom;
mtd-mac-address = <&uboot 0x1fc00>;
};
};
&eth0 {
status = "okay";
phy-mode = "rgmii";
mtd-mac-address = <&uboot 0x1fc00>;
phy-handle = <&phy0>;
fixed-link {
speed = <1000>;
full-duplex;
};
};