mirror of
https://github.com/openwrt/openwrt.git
synced 2024-12-27 17:18:59 +00:00
93610492b6
Netgear WAX214 is a 802.11 ax dual-band AP
with PoE. (similar to Engenius EWS357APV3)
Specifications:
• CPU: Qualcomm IPQ6010 Quad core Cortex-A53
• RAM: 512MB of DDR3
• Storage: 128MB NAND (Macronix MX30UF1G18AC)
• Ethernet: 1x 1G RJ45 port (QCA8072) PoE
• WIFI:
2.4GHz: Qualcomm QCN5022 2x2 802.11b/g/n/ax 574 Mbps PHY rate
5GHz: Qualcomm QCN5052 2x2 802.11a/b/g/n/ac/ax 1201 PHY rate
• LEDs:
4 x GPIO-controlled LEDs
- 1 Power LED (orange)
- 1 LAN LED (blue)
- 1 WIFI 5g LED (blue)
- 1 WIFI 2g LED (blue)
black_small_square Buttons: 1x soft reset
black_small_square Power: 12V DC jack or PoE (802.3af )
An populated serial header is onboard, format is
1.25mm 4p (DF13A-4P-1.25H)
RX/TX is working, bootwait is active, secure boot is not
enabled.
The root password of the stock firmware is unknown,
but failsafe mode can be entered to reset the password.
Installation Instructions:
- obtain serial access
- stop auto boot (press "4", Entr boot command line
interface)
- setenv active_fw 0 (to boot from the primary rootfs,
or set to 1 to boot from the secondary rootfs
partition)
- saveenv
- tftpboot the initramfs image
- bootm
- copy
openwrt-qualcommax-ipq60xx-netgear_wax214-squashfs-factory.ubi
to the device
- write the image to the NAND:
- cat /proc/mtd and look for rootfs partition (should
be mtd11,
or mtd12 if you choose active_fw 1)
- ubiformat /dev/mtd11 -f -y
openwrt-qualcommax-ipq60xx-netgear_wax214-squashfs-factory.ubi
- reboot
Note: the firmware is senao-based. But I was unable to build
a valid senao-header into the image.
Maybe they changed the header format and senaoFW isn't
working any more.
Signed-off-by: Dirk Buchwalder <buchwalder@posteo.de>
28 lines
546 B
Plaintext
28 lines
546 B
Plaintext
[ -e /etc/config/ubootenv ] && exit 0
|
|
|
|
touch /etc/config/ubootenv
|
|
|
|
. /lib/uboot-envtools.sh
|
|
. /lib/functions.sh
|
|
|
|
board=$(board_name)
|
|
|
|
case "$board" in
|
|
8devices,mango-dvk|\
|
|
8devices,mango-dvk-sfp)
|
|
idx="$(find_mtd_index 0:APPSBLENV)"
|
|
[ -n "$idx" ] && \
|
|
ubootenv_add_uci_config "/dev/mtd$idx" "0x0" "0x10000" "0x10000"
|
|
;;
|
|
netgear,wax214)
|
|
idx="$(find_mtd_index 0:appsblenv)"
|
|
[ -n "$idx" ] && \
|
|
ubootenv_add_uci_config "/dev/mtd$idx" "0x0" "0x40000" "0x20000" "2"
|
|
;;
|
|
esac
|
|
|
|
config_load ubootenv
|
|
config_foreach ubootenv_add_app_config
|
|
|
|
exit 0
|