mirror of
https://github.com/openwrt/openwrt.git
synced 2024-12-23 07:22:33 +00:00
79440ea756
The ZBT WE1026-5G (http://www.zbtlink.com/products/router/WE1026-5G.html) is the follow-up to the ZBT WE1026 and is based on MT7620. For the previous WE1026, the ZBT WE826 image could be used. However, as the name implies, the -5G comes equipped with a 5GHz wifi radio. As the WE826 only has a 2.4GHz radio, the addition of 5GHz means that a separate image is needed for the WE1026-5G. I suspect that this image will also work on the previous WE1026, but I don't have a device to test with. The WE1026-5G has following specifications: * CPU: MT7620A * 1x 10/100Mbps Ethernet. * 16 MB Flash. * 64 MB RAM. * 1x USB 2.0 port. * 1x mini-PCIe slots. * 1x SIM slots. * 1x 2.4Ghz WIFI. * 1x 5GHz wifi (MT7612) * 1x button. * 3x controllable LEDs. Works: * Wifi. * Switch. * mini-PCIe slot. Only tested with a USB device (a modem). * SIM slot. * Sysupgrade. * Button (reset). Not working: * The 5GHz WIFI LED is completely dead. I suspect the issue is the same as on other devices with Mediatek 5Ghz wifi-cards/chips. The LED is controlled by the driver, and mt76 (currently) does not support this. Not tested: * SD card reader. Notes: * The modem (labeled 3G/4G) and power LEDs are controlled by the hardware. * There is a 32MB version of this device available, but I do not have access to it. I have therefor only added support for the 16MB version, but added all the required infrastructure to make adding support for the 32MB version easy. Installation: The router comes pre-installed with OpenWRT, including a variant of Luci. The initial firmware install can be done through this UI, following normal procedure. I.e., access the UI and update the firmware using the sysupgrade-image. Remember to select that you do not want to keep existing settings. Recovery: If you brick the device, the WE1026-5G supports recovery using HTTP. Keep the reset button pressed for ~5sec when booting to start the web server. Set the address of the network interface on your machine to 192.168.1.2/24, and point your browser to 192.168.1.1 to access the recovery UI. From the recovery UI you can upload a firmware image. Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
125 lines
3.0 KiB
Plaintext
125 lines
3.0 KiB
Plaintext
/*
|
|
* BSD LICENSE
|
|
*
|
|
* Copyright(c) 2017 Kristian Evensen <kristian.evensen@gmail.com>.
|
|
* All rights reserved.
|
|
*
|
|
* Redistribution and use in source and binary forms, with or without
|
|
* modification, are permitted provided that the following conditions
|
|
* are met:
|
|
*
|
|
* * Redistributions of source code must retain the above copyright
|
|
* notice, this list of conditions and the following disclaimer.
|
|
* * Redistributions in binary form must reproduce the above copyright
|
|
* notice, this list of conditions and the following disclaimer in
|
|
* the documentation and/or other materials provided with the
|
|
* distribution.
|
|
* * Neither the name of Broadcom Corporation nor the names of its
|
|
* contributors may be used to endorse or promote products derived
|
|
* from this software without specific prior written permission.
|
|
*
|
|
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
|
|
* "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
|
|
* LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR
|
|
* A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT
|
|
* OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,
|
|
* SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT
|
|
* LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE,
|
|
* DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY
|
|
* THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
|
|
* (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
|
|
* OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
|
|
*/
|
|
|
|
#include "mt7620a.dtsi"
|
|
|
|
#include <dt-bindings/gpio/gpio.h>
|
|
#include <dt-bindings/input/input.h>
|
|
|
|
/ {
|
|
compatible = "zbtlink,we1026-5g", "ralink,mt7620a-soc";
|
|
|
|
chosen {
|
|
bootargs = "console=ttyS0,115200";
|
|
};
|
|
|
|
gpio-leds {
|
|
compatible = "gpio-leds";
|
|
lan {
|
|
label = "we1026-5g:green:lan";
|
|
gpios = <&gpio2 0 GPIO_ACTIVE_LOW>;
|
|
};
|
|
|
|
usb {
|
|
label = "we1026-5g:green:usb";
|
|
gpios = <&gpio2 2 GPIO_ACTIVE_HIGH>;
|
|
};
|
|
|
|
wifi {
|
|
label = "we1026-5g:green:wifi";
|
|
gpios = <&gpio3 0 GPIO_ACTIVE_LOW>;
|
|
};
|
|
};
|
|
|
|
gpio-keys-polled {
|
|
compatible = "gpio-keys-polled";
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
poll-interval = <20>;
|
|
reset {
|
|
label = "reset";
|
|
gpios = <&gpio0 1 GPIO_ACTIVE_LOW>;
|
|
linux,code = <KEY_RESTART>;
|
|
};
|
|
};
|
|
};
|
|
|
|
&gpio2 {
|
|
status = "okay";
|
|
};
|
|
|
|
&gpio3 {
|
|
status = "okay";
|
|
};
|
|
|
|
&sdhci {
|
|
status = "okay";
|
|
};
|
|
|
|
&ehci {
|
|
status = "okay";
|
|
};
|
|
|
|
&ohci {
|
|
status = "okay";
|
|
};
|
|
|
|
ðernet {
|
|
mtd-mac-address = <&factory 0x28>;
|
|
};
|
|
|
|
&wmac {
|
|
ralink,mtd-eeprom = <&factory 0>;
|
|
};
|
|
|
|
&pinctrl {
|
|
state_default: pinctrl0 {
|
|
default {
|
|
ralink,group = "i2c", "uartf", "spi refclk", "ephy", "wled";
|
|
ralink,function = "gpio";
|
|
};
|
|
};
|
|
};
|
|
|
|
&pcie {
|
|
status = "okay";
|
|
pcie-bridge {
|
|
wifi@14c3,7662 {
|
|
compatible = "pci14c3,7662";
|
|
reg = <0x0000 0 0 0 0>;
|
|
mediatek,mtd-eeprom = <&factory 0x8000>;
|
|
ieee80211-freq-limit = <5000000 6000000>;
|
|
};
|
|
};
|
|
};
|