mirror of
https://github.com/openwrt/openwrt.git
synced 2024-12-27 09:12:39 +00:00
bb6d11e534
Add aliases with "serialN = &uartN;" of uart0/1 on QCA955x SoCs to qca955x.dtsi, to enable uart1 on Linux Kernel. without this: [ 0.342915] ar933x-uart 18500000.uart: unable to get alias id, err=-19 Additionally, remove "serial0 = &uart;" alias from QCA955x device dts/dtsi files. Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
127 lines
1.9 KiB
Plaintext
127 lines
1.9 KiB
Plaintext
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
|
|
|
#include "qca955x.dtsi"
|
|
|
|
#include <dt-bindings/gpio/gpio.h>
|
|
#include <dt-bindings/input/input.h>
|
|
|
|
/ {
|
|
compatible = "mikrotik,routerboard-wap-g-5hact2hnd", "qca,qca9556";
|
|
model = "MikroTik RouterBOARD wAP G-5HacT2HnD";
|
|
|
|
aliases {
|
|
mdio-gpio1 = &mdio2;
|
|
};
|
|
|
|
keys {
|
|
compatible = "gpio-keys";
|
|
|
|
reset {
|
|
label = "reset";
|
|
linux,code = <KEY_RESTART>;
|
|
gpios = <&gpio 1 GPIO_ACTIVE_LOW>;
|
|
debounce-interval = <60>;
|
|
};
|
|
};
|
|
|
|
mdio2: mdio {
|
|
compatible = "virtual,mdio-gpio";
|
|
|
|
gpios = <&gpio 12 GPIO_ACTIVE_HIGH>, /* MDC */
|
|
<&gpio 11 GPIO_ACTIVE_HIGH>; /* MDIO */
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
|
|
phy0: ethernet-phy@0 {
|
|
reg = <0>;
|
|
device_type = "ethernet-phy";
|
|
|
|
phy-mode = "sgmii";
|
|
|
|
at803x-override-sgmii-link-check;
|
|
};
|
|
};
|
|
};
|
|
|
|
ð1 {
|
|
status = "okay";
|
|
|
|
pll-data = <0x03000101 0x80000101 0x80001313>;
|
|
phy-handle = <&phy0>;
|
|
|
|
qca955x-sgmii-fixup;
|
|
|
|
gmac-config {
|
|
device = <&gmac>;
|
|
};
|
|
};
|
|
|
|
&spi {
|
|
status = "okay";
|
|
|
|
flash@0 {
|
|
compatible = "jedec,spi-nor";
|
|
reg = <0>;
|
|
spi-max-frequency = <40000000>;
|
|
|
|
partitions {
|
|
compatible = "fixed-partitions";
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
|
|
partition@0 {
|
|
label = "RouterBoot";
|
|
reg = <0x0 0x20000>;
|
|
compatible = "mikrotik,routerboot-partitions";
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
|
|
partition@0 {
|
|
label = "bootloader1";
|
|
reg = <0x0 0x0>;
|
|
read-only;
|
|
};
|
|
|
|
hard_config {
|
|
read-only;
|
|
};
|
|
|
|
bios {
|
|
size = <0x1000>;
|
|
read-only;
|
|
};
|
|
|
|
partition@10000 {
|
|
label = "bootloader2";
|
|
reg = <0x10000 0x0>;
|
|
read-only;
|
|
};
|
|
|
|
soft_config {
|
|
};
|
|
};
|
|
|
|
partition@20000 {
|
|
compatible = "mikrotik,minor";
|
|
label = "firmware";
|
|
reg = <0x020000 0xfe0000>;
|
|
};
|
|
};
|
|
};
|
|
};
|
|
|
|
&wmac {
|
|
status = "okay";
|
|
|
|
qca,no-eeprom;
|
|
};
|
|
|
|
&pcie0 {
|
|
status = "okay";
|
|
|
|
wifi@0,0 {
|
|
compatible = "qcom,ath10k";
|
|
reg = <0 0 0 0 0>;
|
|
};
|
|
};
|